-
Product
RF & Microwave PXI Switch Modules
-
These switching systems are used for design validation, reliability and production test including 5G, SD radios, S parameter testing for RF cables, antennas, radar and semiconductor verification.
-
Product
Barcode Verifiers
SCANALYST 3
-
Automatic Identification Systems
SCANALYST 3 is a flexible modular platform designed to provide all of the verification functions required for a wide variety of barcode verification applications. All versions have the wide field of view that allows you to inspect both small and large barcodes. This makes it the most versatile barcode verification system available.
-
Product
Verification And Validation Services
-
Verification and validation services using innovative verification and validation techniques throughout the entire quality process for independent evaluation of performance and quality of product designed.
-
Product
x1 PCI Express Extender
SKU-006-01
-
The x1 PCI Express Extender was designed to support the development, debugging and verification of PCI Express boards. The Extender provides a complete PCI Express debugging platform that allows easy access to the logic signals, it has overcurrent protection and hot-swap operation capability.
-
Product
PXI Resistor Module 2-Channel 1.5R to 2.04k
40-293-022
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Multifunction Calibrator 15 ppm Basic Accuracy
MC142
-
Multifunction calibrator MC142 is a precision voltage, current and power calibration source serving as a measurement standard in calibration laboratories and production lines; where verification of electrical measurement equipment & sensors is required. It can be used for calibration and adjustment of meters measuring voltage, current, power, resistance, capacitance and frequency. Internal harmonic and non-harmonic signals make it possible to test electrical performance of meters using signals with various crest factors. Frequency modes enable selection of frequency, amplitude and duty cycle of the output signal. These are suitable for basic calibration of digital and analog oscilloscopes along with transient recorders. The calibrator is equipped to measure temperature with TC and RTD temperature sensors. Its built-in multimeter can be used independently or simultaneously with the calibrator output. Testing of transducers of various types, regulators and sensors can be performed, without the necessity to use any other measuring instrument.
-
Product
Compact, Easy To Use Tester.
Eye-BERT 40G
-
The Eye-BERT 40G packs 40Gbps of test capability and a color touch screen into a compact, easy to use tester. The Eye-BERT 40G offers high performance stand alone bit error rate testing at a fraction of the cost of competing testers. Its small size and stand alone operation allow for convenient field testing of QSFP transceivers as well as link verification and performance testing all in a single unit. The automated QSFP test feature also allows the user to quickly verify transceiver performance and automatically generate a report complete with unit serial number.
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 255 Ohm
40-294-013
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Automated Production Testing
-
Automated production testing is critical in today’s competitive manufacturing environment. Companies can no longer rely on variable costs, non-uniformity, and potential health hazards that come with a laborer-based manufacturing line. This is no less true for sound and vibration tests, ranging from in-process burn-in tests to product validation and verification tests.
-
Product
Calibration Services
-
WTG's calibration package is more than just verification of performance specs. It is a complete package of services including inspection and maintenance. Our services uphold the value of the instrument and extend its lifetime.
-
Product
Pendulum Shock Testing Machine
UDAR-1
-
Pendulum shock testing machine “UDAR-1” is intended for calibration and verification of measuring transducers (both analog and digital) by means of shock impact as well as for shock testing of various specimen.
-
Product
Universal Test System
LS6601A
-
LS6601A Universal Test System is based on LXI bus, primarily used for functional electronic product or system verification, test parameters. Because the system design is based on LXI bus structure, so its addition to general characteristics of versatility, scalability, but the architecture of the system more flexible, the test system is not limited to one or more cabinets, but may be needed test network and multiple LS6601A and can be easily grouped into one or more of the ground test system, depending on the test mechanism, form a powerful set of test, control, simulation, simulation, data management as one; distributed in different places .
-
Product
Generate MC/DC Test
VectorCAST/MCDC™
-
Modified Condition / Decision Coverage (MC/DC) provides two levels of verification for conditional expressions. The first level, named MC/DC Branches, tracks each subcondition in an expression to verify that is has been tested with both True and False values. The second level, named Equivalence Pairs, verifies if each subcondition can affect the value of the condition. This is done by generating a truth table for the expression, and then finding a pair of rows in the table that will generate a different result when all values except the tested value remain constant.
-
Product
EXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5172B
Vector Signal Generator
Achieve faster throughput and greater uptime with cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading ACPR, EVM, and output powerReduce the time you spend on signal creation with Signal Studio software; purchase only the waveforms you need with 5- and 50-pack licensingMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
Test & Control Suite
TestMaster
-
TestMaster is a reliable tool for test systems, test beds, or production facilities in industrial enviroments and a flexible tool in the hands of the engineer, scientist, or plant operator. Like an advanced operating system, its individual modules provide straightforward solutions to diverse measuring and testing tasks. test management, test verification, sequence control, hardware abstraction, process data management proceess data distribution and visualization.
-
Product
PCI Express 5.0 Protocol Exerciser/Analyzer
Summit Z58
Analyzer
The Summit Z58 is a PCIe 5.0 protocol traffic generation test tool used for critical test and verification intended to assist engineers in developing and improving the reliability of their systems. The Summit Z58 can emulate PCI Express 5.0 root complexes or device endpoints, allowing new designs to be tested against corner case issues.
-
Product
VME/VME64x Load Board
-
VECTOR Electronics and Technology, Inc.
The 6U VME and VME64x load board functions to test a system’s cooling capability by applying a variable load to the power supply for verification, then generating necessary heat to confirm the chassis’ cooling. This enables locating hot spots in the chassis so the airflow can be properly directed.
-
Product
PXI Resistor Module 4-Channel 1R to 127R
40-293-012
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Potentiometer Card 3-Channel, 24-Bit, 0 To 16M Ohm
50-296A-121-3/24
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
LIGHT RANGER MUTT
TT9103
-
*Portable and water resistant trailer light tester and trailer brakes tester that allows the user to perform all testing functions without the use of the vehicle*Tests 7-spade, 6-round and 4/5-flat pin type trailer harnesses*Short circuit protection*Turn signal simulation and power verification LED*Water resistant*Trickle charger and trailer plug adapter includedInternal battery compartment (battery not included)
-
Product
100 amu CIS Analyzer
CIS200
-
Stanford Research Systems, Inc.
With better than 1 ppm detection limit, direct sampling at mTorr pressure, and a user-friendly Windows software package, the CIS systems will satisfy your most demanding applications. On-line process monitoring and control, verification of process gas purity at the point of use, high-vacuum residual gas analysis, and process equipment leak checking are some of the areas where these systems will prove indispensable
-
Product
Embedded Development Kit
TySOM
-
The TySOM Embedded Development Kit is for the embedded designer who needs a high-performance RTL simulator/debugger for their embedded applications such as IoT, Factory Automation, UAV and Automotive. The kit includes Riviera-PRO Advanced Verification Platform and a Xilinx Zynq development board that contains single Zynq chip (FPGA + Dual ARM Cortex-A9), memories (DDR3, uSD), communication interfaces (miniPCIe, Ethernet, USB, Pmod, JTAG) and multimedia interfaces (HDMI, audio, CMOS camera).
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 255 Ohm
50-293-013
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Inline Barcode Verifiers
DataMan 475V Series
-
Cognex barcode verification technology ensures the readability and compliance of 1D and 2D barcodes to industry standardization guidelines. Today most companies spot check codes one at a time using an offline, operator-based verifier which can be slow and cumbersome.
-
Product
3D Verification Station
-
Omron’s 3D verification systems provide high-quality imagery to ensure the best results in post-solder inspection.
-
Product
Bench & Characterization Boards
-
Engineer, Design, Fabricate & Assemble Custom Boards for:*Device Characterization and Verification*Bench Testing*Failure Analysis*General Laboratory Use
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
Product
Dual Channel Bit Synchronizer for Rates up to 45 Mbps
LS-45-DB
-
The Lumistar LS-45-DB Dual Channel Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digitaldesign assures a high performance, consistent product, with excellent reliability and long-term stability. Dual channel design can feed each channel of the LS-55-DD dual decom. The LS-45-DB also has a post D combiner that allows for optimal ratiocombining of the two input signals A unique Built-in-Test feature allows performance verification for the Bit Synchronizer to ensure the highest level of operation. Auto-test BIT is performed for a short duration on the application of power and tests more than 90% of the Bit Synchronizer components. This test verifies that power is properly applied, verifies that there are no internal bit errors, and performs other tests to ensure that the bit synchronizer is fully operational with status indication of results. Command-test BIT performs the same functions and can be initiated by the user at any time through the Lumistar software when used on Lumistar PC products. The user has the ability to generate internal pseudo-random patterns and calculate internal bit error rates with or without the injection of forced errors.Various status indicators are also available through the software. The Bit Synchronizer also contains a BER reader as well as frame sync pattern indicator.
-
Product
Multifunction I/O Device
Multifunction I/O
The Multifunction I/O Device features I/O with varying channels, sample rates, output rates, and other features to meet many common measurement requirements. You can use the device for industry applications such as laboratory automation, research, and design verification. The included DAQExpress companion software provides basic measurement and analysis, while the included NI-DAQmx driver provides the ability to create customized automated measurement and control applications. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Barcode Verification Systems
REA ScanCheck 3
-
The REA ScanCheck 3 is an universal, battery-operated, high-performance barcode verification device which operates in accordance with current standards. The verifications document compliance with quality goals in production and monitoring of barcodes on data storage devices and products of all kinds. The measurement principle is based on a laser scanner optimized for verifications. This makes contact-free measurement, largely independent of handling influences, possible. For mobile use on site, the device operates self-sufficiently, independent of the power network with standard, rechargeable batteries. The operating system and application software support multiple languages.
