PCB Inspection
The check and evaulation of Printed Circuit Boards.
See Also: Visual Inspection, Bed of Nails, Flying Probes, AOI, Burn-In, Automated Optical Inspection
-
Product
PCB Test Fixture Kits And Customized Fixtures
-
Mirotech manufactures portable benchtop PCB test fixture kits and provides customized test fixture solutions for the electronics industry. Our innovative, streamlined designs are compact in size and feature a linear collapsing system, interchangeable and reusable plate design, top and bottom probing, and are affordably priced. All fixtures are built using high quality hardware and materials and manufactured using the DATRON M8Cube, known for its precision and accuracy. Each of our custom designs are unique to our customer’s particular project requirements. Fixture kits come pre-assembled, and include blank plates ready for you to drill your test pattern.
-
Product
Smart Inspection Station
SiS
-
Smart Inspection Systems LLC was born in 2010 in response to orthopedic manufacturers’ demands for faster inspection than their sister industries. Our signature product, the Smart Inspection Station™ (SiS™), is an automated turnkey inspection solution that yields comprehensive visual reports with complete geometric form and dimensional pass/fail in just minutes. The SiS™ is custom-configured per the client’s needs, yet versatile enough for simultaneous commissioning on multiple product lines. The product of years of refinement, the SiS™ gives comprehensive visual reports with complete geometric form and dimensional pass/fail in just minutes. Your SiS™ can be custom-configured according to your needs, but is still versatile enough for simultaneous use on multiple product lines. And best of all, every SiS™ purchase comes with ongoing support from L3I’s expert staff.
-
Product
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount
510113122
Receiver Module
Coax, Module, Receiver, CASS, 64 Position, Center PCB Mount.
-
Product
GENERAL INSPECTION MACHINE AFTER SOLDER MASK
-
DVI is a technology of automated optical inspection, which can inspect deep to the difference from semi-transparent layers or semi-reflective layers.
-
Product
Soldering Inspection Video Microscope
MS-1000
-
The MS-1000 is a highly portable microscope for exclusive use with BGA, CSP, and QFP. It is highly efficient in inspecting portions which cannot be inspected by the X-ray inspection method.Specifically, it is efficient for inspecting the following conditions: fillets of soldered balls, melted condition of soldered parts, cracks, defective soldering, etc.
-
Product
Bond Inspection
-
Increasingly thin wires, finer pitches, as well as more applications of thick wire for higher capacities are among the current trends in wire bonding. At the same time, the requirements for robust and defect-free bonds are increasing, for example in assistance systems in the automotive sector and in RF modules in the 5G mobile communications network. This makes reliable inspections extremely important.
-
Product
X5 Pipeline X-Ray Inspection
-
Designed to be integrated into the production line and available with product pipes in 2.5 and 3 ", the X5 pipeline is perfect for a wide range of pumped products such as poultry, meat, slurries and sauces. The system is capable of offering good detection levels on a wide range of contaminants including all metal, bone, glass, dense plastics.
-
Product
9-Pin D-Type, Female, Straight PCB Mount
40-963-009-SF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Explosion Proof UV Inspection Light
-
he Labino MB Hercules Ex is an extremely durable product specifically developed for use in areas where the risk of an explosion is high. Offshore Oil Rigs, Refineries, Aerospace, and Defense often require explosion proof products to ensure safety for their inspection teams. The Midbeam Hercules Ex has successfully completed extremely tough tests, including tests for thermal conditioning, Impact Tests, Drop Tests and IP tests that led to the ATEX certification (Certificate: ITS17ATEX402144X). This unique product is suitable for use in extreme weather conditions varying from 104° Fahrenheit (+ 40° Celsius) to minus 4° Fahrenheit (- 20° Celsius).
-
Product
160-Pin DIN41612 Connector, Straight PCB Mount, Female
40-963-160-SF
DIN41612 Female Connector
Accessory allows a user to create their own PCB based termination solution. This connector is not suitable for directly mounting onto a Pickering switching or cabling product.
-
Product
High-speed In-Line 3D CT Inspection System
X-eye 6300
-
Automatically inspects the defects of products in customer's line with high-speed 3D CT tomography.Able to inspect every defects of Double-sided PCBA & BGA mounted components precisely by solving overlapped X-ray image issue.Inspection speed of 3 sec/1FOV from loading to automatic Good/NG judgement.
-
Product
9-Pin D-Type, Male, Straight PCB Mount
40-963-009-SM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Incremental Length Gauges For Measuring Stations And Multipoint Inspection Equipment
CERTO series
-
*Interferential scanning principle*Very high system accuracy of down to ±0.03 µm*Well-matched ball-bearing guide for very high quality*Defined thermal behavior*Large measuring ranges of up to 60 mm*Interface: 11 µAPP
-
Product
LED Inspection
-
Indicates which LEDs are not working. Checks if all diodes are placed in the correct places. Independently configures a test program for each new LED panel. Fast and effective – 1000 LED panel test takes up to 3 seconds.
-
Product
Defect Inspection Systems
-
Candela® defect inspection systems detect and classify a wide range of critical defects on compound semiconductor substrates (GaN, GaAs, InP, sapphire, SiC, etc.) and hard disk drives, with high sensitivity at production throughputs.
-
Product
78-Pin D-Type Male Right-Angle PCB
40-963-078-RM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Pinhole Detection Inspection Kit
Elcometer 270
-
The Elcometer 270 Pinhole Detectors Inspection Kit utilises the wet sponge technique and has been designed to set a new standard for wet sponge detectors - a high quality, low voltage detector with similar accessories to a high voltage spark tester.
-
Product
PCB Connectors
CMD Series
-
Smiths Interconnect's versatile, high density CMD connector solution for board to board and wire to board with built in coding and keying as well as ESA qualification
-
Product
Non-Destructive Inspection Equipment
-
Non-destructive inspection means that various materials such as metal are "without damaging the object, knowing the presence or absence of scratches on the surface or inside and the degree of scratches, and passing the object against standards such as standards.
-
Product
PCB Test Fixtures
-
ATE, ICT, semiautomatic & manual electronic test fixtures, PCB test fixtures, cable test fixture, wiring harness test fixtures, dedicated test fixtures, functional test fixtures, electronic test fixture programming. PADS Schematic capture, circuit board layout, PCB design prototype, solder paste stencils, X-Y coordinate data, B.O.M. maintenance, and manufacturing documentation, Gerber data.
-
Product
A Compact X-ray Inspection System, The MedaScope™ Desktop
-
A compact X-ray machine weighing only 55 pounds, the MedaScope Desktop is easy to carry and can be set up rapidly. Glenbrook’s MedaScope Desktop is a portable, compact manual system for real-time, magnified x-ray screening of packaged devices including medical devices, electronics, and cables.
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
37-Pin D-Type Female Right Angled PCB HV
40-963-037-RF-HV
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Solder Joint Inspection System
-
DMC developed the software to inspect the solder joints of automotive power door lock switches.
-
Product
200-Pin LFH Connector, PCB Mount, Straight Male
40-963-200-SM
LFH PCB-Mount Connector
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Auto Macro Wafer Defect Inspection
EagleView
-
EagleView automated macro defect semiconductor wafer inspection system provides industry leading throughput, defect detection accuracy, and wafer classification for semiconductor manufacturing. EagleView systems have inspected over 100 million semiconductor wafers worldwide. The EagleView macro defect inspection tool resolves many of the problems and pitfalls of manual and micro wafer inspection by automating and standardizing semiconductor wafer inspection processes while creating complete images of every wafer in the cassette. Unlike manual micro defect wafer inspection, EagleView’s automated wafer inspection is always consistent, tireless, reliable, and fast. EagleView helps find macro defects while there’s still time to take corrective action.
-
Product
Inspection + Cleaning for High Volume Manufacturing Environments
AVIT-2020
-
AVIT-2020 is a fully automated system that removes human subjectivity from the entire inspect-clean cycle. With integrated cleaning and fast, robotic mechanics, operators simply press the process button, allowing them to complete a week’s worth of inspections in just a couple of hours with almost zero active operation.
-
Product
Non-Destructive Test Resonant Inspection Station
RAM-TEST-FIXTURE
-
The NDT Test Station, Model RAM-TEST-FIXTURE Resonant Inspection System is an ideal choice for testing when repeatable manual inspections are required. The innovative Test Station allows precise control of part positioning with an adjustable table ranging up to 6.25 inches (158.75 mm) in height.
-
Product
Solder Past Inspection
-
From the innovative Z-Check 3D through to the entry level Z-Check 100 the entire range has been designed to provide accurate pad specific measurement of solder paste deposits, adhesives and component placement. Amongst its other features the Z check software comes with the convenience of a full SPC package as standard.
-
Product
Industrial Inspection Cameras
-
Industrial Inspection Cameras are our top-of-the-line inspection cameras. They feature glass lenses, superior optics, crystal-clear displays, and compatibility with the thinnest probes on the market. All Industrial Inspection Cameras were recently upgraded to capture VGA (640 x 480 pixel) resolution video clips and remove glare and reflections from them. All cameras in this sub-category are made in Taiwan, making them compliant with the Trade Agreements Act (TAA) of 1979a necessity for many buyers with the U.S. military and federal agencies.
