-
Product
Cable Fault Locating Equipment
-
Commonly used to test underground coaxial and twisted pair cabling, along with transmission lines and other industrial electrical cables.
-
Product
Visual Fault Locator
FFL-310-U
-
FFL-310-U Visual Fault Locator is equipped with a 650 nm high power visible laser diode,can be operated in -CW (continuous) or … MOD (1Hz modulation) mode. There is one LED indicator：with RED or GREEN light; the RED one shows the operating mode of the laser diode output signal, and the GREEN one indicates low battery level. FFL-310-U is designed in a card-size dimensions.
-
Product
Cable Test Van
BAUR Transcable 4000/S 110-1
-
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.
-
Product
Tool, Locator, TriPaddle, ITA
910104107
-
Used with Crimp Tool p/n # 910101103 to crimp TriPaddle contacts to 20-28 AWG wire.
-
Product
Tool, Locator, TriPaddle, Receiver
910104127
-
Used with crimp tool part # 910 101 103 to crimp TriPaddle receiver contacts to 20-28 AWG wire. This locator contains an integrated wire stop for consistent contact crimping.
-
-
-
Product
Touch Screen 1550nm Single Mode Mini OTDR
TR1500S
-
Shenzhen Sharingtek Communication Co., LTD
The TR1500S mini OTDR is compact and easy to carry. It adopts a 3.5 inches high-definition touch screen, supports multi-touch and smooth operation, integrates OTDR, event map, optical power meter, light source, visual fault locator and flashlight in one unit, to meet various test needs in different occasions. The OTDR function adopts 1550nm wavelength and is built in high-efficiency wavelength isolator. It can perform optical live test on 1490 and 1577nm optical links, which supports up to about ±10dB optical live test. Its maximum measurement range is 80km.The TR1500S is used to measure optical fiber’s length, loss, connection quality and other parameters. It can easily test the breaking point, bend and loss point of the optical fiber links. It is suitable for maintenance personnel to have optical line maintenance and emergency repair testing.
-
Product
Network Cable Testers
-
Companies expect their Ethernet twisted pair cabling to work flawlessly, but corners cut during design, installation and testing result in network downtime which translates to wasted resources and lost revenue. This can be avoided by cable installers that can install copper cabling systems and locate faults quickly.
-
-
Product
Touch Screen Mini OTDR, 1310/1550nm
TR1200 Series
-
Shenzhen Sharingtek Communication Co., LTD
1. 4.3-inch multi-touch capacitive screen support zoom function screenshot2. Intelligent multi-function 12-in-one functional module: automatic OTDR expert OTDR event map optical power meter visible fault locator adjustable light source optical loss test RJ45 sequence test RJ45 length test RJ45 digital tracker flashlight end face detection (optional)3. Automatic OTDR no complicated settings one-key test4. Expert OTDR professional measurement mode simultaneous display of curve list and MAP view5. Event blind zone 2.5m attenuation blind zone 8m measuring range up to 100KM6. Support optical test with optical signal less than -5dBM high isolation bilateral filter technology7. Support automatic saving SOR file format 8G storage capacity 200000 records can be stored8. Support Type-C charging interface 4000mAh polymer battery battery life is more than 12 hours
-
Product
Tool, Locator, QuadraPaddle, ITA
910104140
-
Used with Crimp Tool p/n # 910101103 to crimp QuadraPaddle contacts to 22-28 AWG wire.
-
Product
Tool, Locator, TriPaddle, Receiver
910104146
-
Tool, Locator, TriPaddle, Receiver (only for contact p/n #'s 610110128 Rev C+ and 610110177)
-
Product
PXI/PXIe Fault Insertion Switch, 74-Chan 2A, N/C Through Relays, Fault Buses on M & U
42-190C-012
-
The 40-190C-012 (PXI) and 42-190C-012 (PXIe) are fault insertion switches with 74 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
-
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 8 Channel
40-201-008
-
This high bandwidth differential PXI fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
Dual Bus 36-Channel 2A PCI Fault Insertion Switch
50-190-202
-
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Cable Fault Locator
TX2003
-
6 km (19,000ft) 0.5mtr dead Zone Selectable Cable Impedance Warble Tone Generator Rapid Fault Location Large 128x64 LCD with Backlight Scratch Resistant Display Environmental Protection IP54 CE Approved 3yrs Manufacturers Warranty 60 Hours Battery Life
-
Product
Dual Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-002
-
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
Portable GIS Partial Discharge Detector
JHPD-10
-
Xiamen Jiahua Electrical Technology Co.,Ltd
JHPD-10 quickly and accurately detects various kinds of partial discharge signals that occur with insulation defects in GIS. Attached on the surface of GIS the detector collects the inside discharge signal of impure gas, suspension potential and solid insulation material. The diagnostic software analyzes the fault character and locates the fault to avoid electricity accident. The device is for daily patrol inspection with high efficiency and easy operation features. Designed with two UHF signal channels, one detects the partial discharge signal; another excludes the disturbance signal like corona discharge in the air and mobile phone communication.
-
Product
PXI Single Bus 74-Ch 2A Fault Insertion Switch
40-190B-001
-
The Single Bus, 74 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
-
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
PXI Dual Bus 32-Chan 2A Fault Insert Switch
40-190B-202
-
The Dual Bus, 32 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Tool, Locator, Micro Coax, Receiver
910101135
-
Included with Crimp tool kit p/n 910101132 and kit p/n 910101131.
-
Product
PXI Single Bus 64-Ch 2A Fault Insertion Switch
40-190B-101
-
The Single Bus, 64 Channel PXI Fault Insertion switch is part of our family of 2 Amp fault insertion solutions, The range includes modules with 74, 64 or 32 channels and single or dual fault buses. This version has normally closed through relays, so in the default state, there is a path between input and output for all signal channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
Product
Battery Fault Insertion Unit
-
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
-
Product
PXI 22-Channel 2A Fault Insert Switches
40-202-001
-
This is the 22 Channel version of the 40-202 Fault Insertion Switch. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test.
-
Product
PXI Fault Insertion Switch, 6-Channel, Two Fault Buses, 30 A, Hardware Interlock
40-191B-012-HI
-
The 40-191B-012-HI is a PXI fault insertion switch with hardware interlock using solid state switching elements and is capable of carrying 40A on single channel or 30A on all channels at the same time and provides a robust solution to high current fault insertion.
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
-
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
