LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
NI-9421, 24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module
NI-9421 / 779002-01
Digital Module
24 V, 8-Channel (Sinking Input), 100 µs C Series Digital Module - The NI‑9421 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels and has an LED indicating the state of that channel. The NI‑9421 offers isolation between the input channels and earth ground.
-
Product
Radiometer
X1-1-RCH-116-4
-
The X1-1 radiometer from Gigahertz-Optik features an RCH-116-4 detector and is ideal for measurement of the irradiance of high power LEDs in the UV-A and blue light range. The device can accurately measure irradiance levels of up to 40,000 mW/cm². One of the outstanding features of the RCH-116-4 detector is its proven concept of a passive radiation absorber coupled to a UV sensor. This provides stability even in high temperature and intense UV radiation environments. In addition to the passive radiation absorber, the device also has a cosine-corrected field of view. The sensor’s housing also serves as a handle. The battery-powered X1-1 optometer supports a usable dynamic range from less than 1 mW/cm² to 40,000 mW/cm² thanks to its high-end signal amplifier. It can be used to perform precise measurements of up to 5 standard LED wavelengths for which the detector was calibrated for active irradiance. In addition to the CW measurement function, the device also has a dose measurement function. The radiometer can be used with other detectors from the RCH series. e.g. for gas discharge lamps. Remote control of the device is possible via its user software and a software development kit is offered for integration of the device in the user’s own software.
-
Product
Logger version chlorophyll and turbidity sensor with wiper
INFINITY-CLW ACLW2-USB
-
Infinity-CLW is an autonomously deployable data logger for long-term chlorophyll and turbidity measurements. The light sources (LEDs) of chlorophyll and turbidity sensors are highly stable, Minimizing the change over time. The instrument has a mechanical wiper that periodically sweeps to inhibit biological growth on the optical window. The turbidity sensor has a good correlation with SS (Suspended Solid) over the range. Infinity-CLW provides Highly accurate and long-term stable chlorophyll and turbidity data in oceans, rivers and freshwater.
-
Product
Torque Tester
DI-4B-25
-
For daily inspection of small impact tools. Since the display uses an LED, the numbers can be read clearly even in dark places
-
Product
Handheld Water Quality Meters
LAQUA DO210
-
Measures dissolved oxygen (DO) concentration in ppm (mg/L) and % saturation0.01 mg/L or 0.1% DO resolutionCompensates salinity, temperature, and atmospheric pressure Allows up to 2 calibration points using galvanic DO electrode°C & °F temperature readingsAuto log data; built-in memory can store up to 500 dataAuto stable, auto hold, and real-time measurement modesAuto shut-off (programmable: up to 30 minutes)Built-in electrode holder allows 2 electrodes to be attached Monochrome LCD with white LED backlight: 50 x 50 mmCasing is IP67 waterproof/dustproof, shock & scratch resistant, non-slipPowered by 2 x AA batteriesPackaged with galvanic electrode in carrying case3 years meter warranty
-
Product
Calibrating Equipment
-
Stability DC : < 0.01 %FS / 3 min, AC : < 0.02 %FS / 3 minRipple : < 0.2 %Power Supply : 230 VAC, 50 (60) HzPower Consumption : < 250 VAOperating Temperature : 5ºC to 35ºCRelative Humidity : ≤ 80 %Distortion : < 0.5 %Display : 51/2 Digit LED Digital DisplayStep adjustment of Output Signal : 100 %FS / N, 10 %FS / N,%FS / N, 0.1 %FS / N (N = 4, 5, 6, 10 and 15)Dimensions : 190mm (H) x 480mm (W) x 545mm (D)Total Weight : 22.5 kgs (approx.)
-
Product
6.5" 640 X 480, VGA/DVI Interface, Ultra Slim Touch Open Frame Monitor
IDS-3106
-
6.5" 640 x 480 VGA panel with LED backlight for 20% power saving and environmental protection, 0~50° C wide operating temperature support, 4-wires resistive touchscreen solution.
-
Product
LED Backlight Drivers For Automotive
-
Renesas' automotive LED backlight drivers offer dimming solutions for a wide variety of ambient lighting conditions in automotive applications.
-
Product
Non-Contact H.V. Detector
278 HP
-
Standard Electric Works Co., Ltd
Protection class : IP65. 3 LED indicators in a circle for easier viewing in any directions (360° LED indication). 8 voltage settings : 240V, 2kV, 6kV, 11kV, 22kV, 33kV, 132kV, 275kV. Bright LED visual indication. Frequency range: 40~70Hz. Longer hood makes LED indicators more visible. Audible indication. Easy-to-prove method. Self-test function. Power source : 1.5V "C" type battery × 3. High impact nylon casing. Non-contact detection by proximity. Compatible with most hot sticks. Lightweight, robust & compact. Suitable for indoor and outdoor use. Easy access to batteries. Special ranges are available upon request. The maximum detection range can be 500kV.
-
Product
Mainframe or -E Expansion Chassis - Control up to 16 Modules with up to 8 Relays per Module
LXA/128-MF
Chassis
These Chassis control up to 16 modules with up to 8 relays per module. A large variety of different switch modules are available to build almost any configuration. Modules are available to build matrix or mux configurations or discrete relay modules. Input detection modules, output driver modules and proto board modules allow custom systems for almost any application. LEDs on the front panel show switch and power status. A thumbwheel manual control is optional.
-
Product
Contacting Tip Fiber-Optic Probes
Fiber-optic Probe
Our Fiber-optic Probes with Contacting Tips are designed to achieve a more refined intensity measurement. The intensity response of a Sensor is influenced by several factors, including brightness and size of the LED under test, the aperture of the Fiber-optic Probe that is being used to test the LED, and the distance between the LED and the Fiber-optic Probe tip.
-
Product
8-Ch Power Relay Output Module With LED
ADAM-5069
Relay Output Module
High Power Relay Output : 250Vac@5A, 30Vdc@5A8-channel Relay Output8 form A channels8 LED indicatorsJumper setting for output status when reset
-
Product
Battery Charger-Analyzer for small battery systems (up to 10A-Hr)
24-400xg
-
The 24-400XG is an instrument designed to charge, trickle charge and analyze (discharge) Nickel-Cadmium, Sealed Lead-Acid and other types of rechargeable batteries.With its multiple modes of operation of Constant Current Charge (dual and single rate), Constant Current & Float Charge, Constant Current & Peak Stop Charge, Automatic Discharge (analysis), Resistance Discharge (analysis) and Full Discharge (deep cycle), the 24-400XG can satisfy the requirements of most small (0 to 10 A-hr) rechargeable battery systems.The instrument features safety interlocks to protect the operator, the charger and the battery in the event of reversed polarity connection, short circuit, open circuit (no load) and Overvoltage conditions.Two large LED digital meters permit the simultaneous monitoring of voltage and current, while eight indicator lights inform of the status of the operation.
-
Product
12-690V Voltage Tester With LED/LCD Display
7339
-
Peaceful Thriving Enterprise Co Ltd
Measurement by LED Display1. Double-pole Test2. High Voltage Indication3. Phase Rotation Test4. Polarity Indication5. Continuity Test6. Illumination
-
Product
7“ WSVGA,1000nit LCD
IDK-2107W
-
7" LCD supports 1024 x 600 pixels, Brightness of 1000 cd/m2 with LED backlight, Wide operating temperature (-20 ~ 70 °C) Projected Capacitive touch solution.
-
Product
Network Analyzer, Tester, LED
72-9450
-
This cable tester allows for quick and easy troubleshooting of RJ45 and USB cables. Checks for continuity, faulty wiring, open, shorts, straight through or cross pinning of cables.
-
Product
Power Over Ethernet (PoE)
-
Power over Ethernet (PoE) is a revolutionary technology that enables delivery of power over standard Ethernet infrastructure to facilitate quick and easy installation of WLAN access points, network cameras, IP telephones and other IP-based devices. The proliferation of Ethernet-connected devices such as Pan-Tilt-Zoom (PTZ) security cameras, 802.11ac and 802.11ax access points, LED luminaires and Internet of Things (IoT) appliances has created an unprecedented demand for more power. PoE is the key to efficiently, cost-effectively and reliably power network devices.
-
Product
SparkFun LED Driver Breakout
LP55231
-
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED controller. Remarkably simple, the breakout is equipped primarily with just the LP55231 LED controller IC, plus three RGB LEDs. It also features pads and jumpers for replacing the onboard LEDs with external ones, and configuring the I2C bus, which allows you to daisy-chain up to four LP55231s. This breakout drives the LEDs using Pulse Width Modulation (PWM), so it is well-suited for variable intensity and color-mixing applications!
-
Product
Absolute Optical Encoder
A2
-
Product DescriptionRestriction of Hazardous SubstancesThe A2 absolute encoder is a non-contacting optical rotary position sensor which reports the shaft angle within a 360 deg. range. As opposed to incremental encoders, the A2 reports the absolute position rather than the change in position. When powered up, it does not require a home cycle, even if the shaft was rotated while the power was off. In multi-turn mode, it tracks the position in a 32-bit counter as long as the power supply is maintained. Internally, an infrared LED flashes through a circular bar code onto a linear array sensor. The microcontroller decodes the image into a unique position. All user programmable parameters such as resolution, origin, direction and mode are permanently stored in an internal EEPROM
-
Product
Voltage Testers
-
Non-Contact Voltage (NCV) tester quickly checks for the presence of voltage in AC powered systems. It can be safely used up to 1000 V AC. When AC voltage is detected, the testo 745 gives indication by flashing of its RED LED tip and buzzing of its internal audible buzzer. You can easily determine the hot and neutral legs of an outlet without time consuming and risky removal of the outlet from the outlet box.
-
Product
Low Cost Emulator
EB-ST62
-
# Supports Most of the ST62 Microcontrollers# Real-Time Emulation up to Device Frequency# 3.3V and 5V Operating Voltages# Real-Time Trace Buffer# Source-Level Debugger for C and Assembler# Unlimited Number of Breakpoints# Stack Overflow Debug Breakpoints# 8K Bytes Emulation ROM# 192 Bytes Emulation RAM# 128 Bytes Emulation EEPROM# On-Board Switches and LEDs
-
-
Product
Pocket Colorimeter Illuminance Meter
HPC-3
-
Shenzhen Chuangxin Instruments Co., Ltd.
● Adopting micro-spectrometer technology which is more accurate than traditional photo-detectors .● Measure chromaticity coordinate temperature, chromaticity coordinate, rending index, color difference, etc● Data hold, save and open-function. Several groups of data can be saved. ● Accuracy of chromaticity coordinates :±0.003(x ,y)● 128*64 LED of graphic interface displaying spectrum wave, chromaticity diagram● USB interface for PC communication● Quality Li-Battery for recycled-utilization● Range of wavelength：380nm－780nm；● wavelength accuracy：±0.5nm Repeatability：±0.2nm ● Accuracy of chromaticity coordinate:±0.0025, Resolution：0.0001；● Correlated color temperature：1500-25000K, Accuracy：±3%，Resolution：1K； ● Accuracy of total color difference：within±0.2 (under standard illuminate A）；● Range of Illumination measurement：1.0lx-100klx;● Accuracy of Illumination measurement：Class 1
-
Product
Specialty Testers
-
Test Voltage from 120V to 600V AC/DCNon-Contact Voltage Sensor from 90V to 1000VTest Continuity & PolarityCase serves as prod holder for one-hand operationSelf-storing prodsSolenoid Sensing indicated by LEDs & VibrationErgonomic Soft PVC housing for comfort gripLED Spotlight Illuminates Work AreaBattery not Included (AAA x 1)
-
Product
Battery Capacity Analyzer
Model BCA6/12M
-
- Instant Measurement of energy stored in a storage battery- Tests 6V or 12V Lead Acid Batteries from 2Ah to 100Ah Capacity- Suitable for any SLA, GEL or Car Flooded Batteries- Displays DC Voltage and Balance available Ah capacity of the battery- Shows the Internal Resistance of the battery- Powered by the Battery under test- Micro-processor based digital control of entire testing process- Specially designed 4-terminal probing Battery Clamp of 100A capacity- Test simulates 20-Hr discharge test (C/20) with a few seconds- Bright, back-lit LED Display for test process display- On-screen User Guidance for testing on the built-in LCD Screen- Easy to use, portable and robust housing in a custom extrusion
-
Product
Probe Series
GEMINI Series
-
Micro LED (µLED) is a disruptive optical technology breakthrough in the display industry. Micro LED displays offer tremendous potential for consumer/ display/ automotive applications because they are brighter, faster, and longer life compared with other emissive devices.
-
Product
PXIe-4137, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit
783761-02
Source Measure Unit
PXIe, ±200 V, ±1 A DC, ±3 A Pulsed, Up to 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4137 is a high-precision, system source measure unit (SMU). It features 4-quadrant operation and sources up to 40 W of DC power and can pulse up to 500 W. Analog-to-digital converter technology helps you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module also can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. The PXIe-4137 is ideal for a broad range of applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers
-
Product
19" SXGA Industrial Display Kit
IDK-1119
-
19" LCD supports 1280 x 1024 pixels and wide operating temperature (0 ~ 50° C) Brightness of 350 cd/m2 with LED backlight. 5-wire resistive touch solution, High contrast ratio of 1000:1, High uniformity of 80%.
-
Product
Video Signal Generator
MSPG-7800S
-
Analog was a main item in display device industries at the past time, but from now on, the digital is getting developed with multi-function and large-sized resolution like 4Kx2K. Preparing for this change, this signal generator is an essential equipment of LCD, LED, PDP, D-TV, TV, CRT display device industries, which was made for generator analog signal, digital signal, TV signal and D-TV signal, HDCP, code simultaneousl and sufficiently examining a large-sized display device.
-
Product
Vapor Concentration Monitor
IR-300 Series
-
Metal-Organic Chemical Vapor Deposition (MOCVD) is widely used in the manufacture of LEDs, optical devices and other components. Liquid and solid precursors are delivered to the reaction chamber by controlling the temperature, pressure and the carrier gas flow rate (bubbling method). Process results can be affected by changes especially in temperature and liquid level. The in-line IR-300 Series measures and reports the precursor concentration in real time.
