-
Product
Variable Gain Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support a broad family of Variable Gain Amplifiers (VGAs) for RF, microwave, and millimeter wave applications. Our VGAs cover frequencies from 50 MHz to 40 GHz and are used in a variety of Network, Commercial and Aerospace and Defense applications. These products are available in industry standard plastic packaging and are designed for both 50 Ohm and 75 Ohm applications.
-
Product
PHIL 4-Quadrant Power Amplifier
PAV5000
-
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
Product
Tone Amplifier And Tone Generator Set
AM5/TG5xs
-
The New Tone & Amp Set are state of the Art Testers offering touch button technology, visual qTrace (quick trace) as well as audio tracer tone technology providing accurate wire location, high output volume and sensitivity, tone tracker functionality, Visual/Audible indication of Digital Traffic, filtered amplification with multiple volume levels and two normal tones and four tonetracker tones with constant and variable interrupt rates, short detection and indication, capacitive output connection, Quick change battery and low battery indication in New custom designed High impact resistance enclosures, fully sealed to IP67.
-
Product
Low Noise Amplifier (DC Powered)
-
RF Lambda’s DC low noise amplifiers (LNA) are broadband and offer low noise figure high IP3. Hermetically sealed options are available upon request.
-
Product
Driver Amplifiers (< 3 W)
-
Qorvo's driver amplifiers are designed to provide good linear or efficiency performance for gain stages prior to the final power amplifier in a transmitter chain. These products support frequencies up to 46 GHz, using process technologies such as InGaP HBT, power pHEMT, E/D pHEMT and GaN.
-
Product
Amplifier Systems Broadband
-
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
Product
Mini Pneumatic, Contact, Receiver, Push-in Fitting, for 4 mm OD Tubing
610131111
Pneumatic Contact (Receiver)
Primary mating contact 610132111.Please note: This contact cannot be used to fully populate any compatible VPC module. The larger head size prevents directly adjacent placement.
-
-
Product
Motion Based Waves
-
Accurate Motion Based wave measurements are critical in applications such as offshore wind farm development, navigation, cable laying, breakwater building, and bridge construction.Waves also result in continuous loads on marine structures, including docks, moorings, and offshore platforms.Motion Based Waves are challenging to measure. Variables to consider when collecting wave data include the depth of the measuring device, proximity to shore, wave types, and available infrastructure from which to measure.Several methods for measuring motion based waves are available, and careful selection of the best approach is needed to get the optimal result.
-
Product
Millimeter-Wave Amplifiers
-
When your application requires operating at Ka-band and above, trust Mercury Systems’ millimeter wave amplifiers to perform. With standard designs up to 65GHz and custom products available, Mercury is ready to support your high frequency requirement.
-
Product
Low Phase Noise Amplifiers
-
Pasternack's low phase noise amplifiers cover select frequency bands ranging from 1.5 to 18 GHz with residual phase noise levels as low as -180 dBc/Hz @ 10 KHz offset. Additional performance specs include small signal gain ranging from 9 to 14 dB, with typical noise figure of 5.5 dB. Psat levels for these amplifiers range from +16 to +25 dBm with Output IP3 levels as high as +34 dBm. All models feature single DC voltage supplies and input/output RF ports are internally matched for 50 ohms with DC blocking capacitors. These compact module assemblies require no external components and are available in rugged Kovar metal drop-in packages that are gold-over-nickel-plated and support field replaceable SMA connectors. All models are EAR99 and guaranteed to meet MIL-STD-883 test conditions for hermeticity and temperature cycle.
-
Product
Panel-mounted Power Amplifier
PAC2000B
-
PA series amplifiers are specially designed for power network real time simulation applications,which requires large power output,high accuracy even at high current output for all kinds of load.
-
Product
Amplifiers - Solid State
-
PMI offers a full line of RF and Microwave Amplifiers that range from 250 kHz up to 50.0 GHz. Many options are available. If you do not see exactly what you require on this website, please contact sales@pmi-rf.com because we offer amplifiers designed and built to your specifications at catalog prices.
-
Product
Low frequency Amplifiers
-
Low-frequency amplifiers Current sources Systems with multiple amplifiers Customized systems
-
Product
RF High Power Amplifier Modules
-
Analog Devices MMIC-based GaN and GaAs power amplifiers cover the low hundred MHz frequency range up through and including components in the Ka-band (29 GHz to 31 GHz). Our portfolio also includes GaN-based power amplifier modules with output power exceeding 8 kW. Designed for excellent linearity at high output power, our power amplifiers maintain good heat dissipation and high reliability at elevated temperatures for the wide variety of test, radar, and aerospace and defense applications that they are used in.
-
Product
RF Bidirectional Amplifiers
-
Miniature, high-efficiency and linear bidirectional amplifier modules (transmit and receive). 1.0 to 2.5 GHz, automatic or manual T/R switching, high-efficiency or high-linearity models. Custom designs available through RF PA design services.
-
Product
Standard 1.08 (31.00) - 4.00 (114.00) Long Travel Bead Probe
BPLT-25F-4
Bead Target Probe
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,460Overall Length (mm): 37.08Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, Alternate Spring 400 mil / 10,16 mm, High Spring: 400 mil / 10,16 mm, Ultra High Spring: 350 mil / 8,89 mm
-
Product
DP Range Broadband Power Amplifiers 10 kHz - 250 MHz
DP Series
-
Class A solid stateBroadband (instantaneous single band): 10 kHz 250 MHzTypical output power : 1000 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB>600 W and H<-20 dBcAir cooling: self contained fansCan operate in full mismatch conditions without damageReliable, efficient and robust19" Cabinet on wheels3 years standard warranty
-
Product
RF Amplifiers Bias Controllers
-
RF amplifier bias controllers generate a regulated drain voltage and actively adjusts the gate voltage of an external amplifier to achieve constant bias current. It can be used to bias any enhancement and depletion type amplifier operating in Class-A regime with drain voltages (VDRAIN) as specified. These devices achieve excellent bias stability over supply, temperature and process variations, and eliminates the required calibration procedures used to prevent RF performance degradation due to such variations.
-
Product
Amplifier Module
LNAM-FBX
-
Ultra-low-noise voltage amplifier module (LNAM) with ac coupled FET input allowing measurements between 1 Hz and 20 MHz. High gain precision and low distortion are achieved by using internal negative feedback and >1000 V/µs output stages.
-
Product
Low-Noise Amplifier
CARM-02
-
HYPRES is proud to announce an Analog-RF Amplifier product. Using state-of-the-art low-noise amplifier and compact cryogenic cooler, the Cryogenic Analog RF Module (CARM-02) provides amplification with extremely low noise.
-
Product
Lock-in Amplifier
HF2LI
-
The Zurich Instruments HF2LI (high-frequency, 2 inputs) is a digital lock-in amplifier covering the frequency range between DC and 50 MHz. It features 2 physical input channels so that it can replace 2 devices in many measurement setups. The 128-bit digital signal processing delivers superior precision thus boosting both the noise performance and the dynamic reserve. With these unprecedented capabilities, the HF2LI brings lock-in amplification to a new level and enables new applications in a frequency range that was previously tied to analog instrumentation. The computer is connected by a high-speed USB interface, which allows data acquisition at high rates. The HF2LI is delivered with a fully featured graphical user interface and a choice of programming interfaces that greatly add to the usability of the instrument.
-
Product
Mixer Amplifiers
-
Tailored for various establishments such as restaurants, schools, churches, clubs, and more. This versatile unit offers a compact and highly efficient solution to seamlessly blend up to three audio sources.
-
Product
Millimeter Wave Antenna Testing
-
If you are involved in antenna or system level design using mmWave or THz frequencies, then you understand the importance of dependable testing equipment. It may be that you are designing passive phase array or that you are designing a mmWave radar sensor system, but when it comes to validation of your design, simulation can only bring you so far. Phased array antennas have to be measured over the air (OTA) to ensure the radiation pattern of your design efficiently conducts energy in the right direction which is where the MilliBox comes in.
-
Product
Broadband Amplifiers
-
Blonder Tongue Laboratories, Inc.
Blonder Tongue offers a variety of RF amplifiers for broadband CATV or OTA (over-the-air) applications. Be it a 1GHz power doubling two-way indoor distribution amplifier or a mast-mounted preamplifier, or anything in between, we have you covered.
-
Product
Gain Block Amplifiers
-
Qorvo designs and manufactures a wide selection of general-purpose, internally matched MMIC amplifiers that are targeted for many applications in network infrastructure and defense / aerospace. These components showcase the wide range of performance capabilities using Qorvo's processes. Our general-purpose gain blocks are internally matched and offer various gain and linearity levels in a variety of package types, giving customers many options for system design.
-
Product
Voltage and Current Amplifier
CMS 356
-
The CMS 356 is a voltage and current amplifier for analog low-level signals provided by a CMC test set or by any other signal source, such as a digital real-time power system network simulator. When used in combination with a CMC test set, the amplifier extends the capabilities of the test set to provide additional output channels and higher amplitudes.
-
-
Product
Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier
USBPGF-S1
-
Single Channel USB Programmable Anti-Alias Low-Pass Filter and Instrumentation Amplifier for Signal Conditioning in Data Acquisition Systems. Differential or single ended input. 10Vmax Signal Input and Output with input protection up to 40V. Software-programmable instrumentation amplifier gains of 1 to 1000.
-
Product
Rail-to-Rail Op Amplifiers
-
Analog Devices high speed (> 50 MHz) rail-to-rail op amps enable you to operate at lower supply voltages, swing closer to the rails, and provide wider dynamic range. Featuring a portfolio with a wide variety of op amps, including both rail-to-rail input/output as well as just rail-to-rail output, ADI provides the widest portfolio of leading edge products available on the market. Whether it is wide bandwidth, high slew rate or low distortion, or rail to rail, no one sets more performance standards for next generation designs than Analog Devices.
