Product

High-Voltage Dividers & Capacitors

-

Measurements International Ltd.

Measurements International Ltd.

300 V to 300 kV, Outputs of 120 Vac, Primary Standard HV Measurements, Loss Measurement Systems, IEEE-488 Interface, Division Accuracy < 20 ppm, Calibration Period 3 to 5 Years.

Product

MPOD Crate

-

W-IE-NE-R, Plein & Baus GmbH

W-IE-NE-R, Plein & Baus GmbH

WIENER presents with Mpod a new, universal multi-channel low voltage (LV) and high voltage (HV) computer controlled power supply system. Offering highest channel density the MPOD mainframe can house up to 10 plug-in modules which results in 80 up to nearly 500 individually controlled channels per mainframe. Built in a modular way MPOD consists of the mainframe / bin, a front side plug-in controller with Ethernet and USB ports, a fan tray and a power supply which is located in the back.

Product

High Voltage Safe Measurement Systems

-

CSM Products, Inc.

CSM Products, Inc.

For measurement on high-voltage components with certified safety – in test drives, field tests, and on test benches: CSM’s high-voltage measurement systems are specifically designed for the safe and accurate acquisition of temperatures and analog sensor signals in HV environments, especially in electric and hybrid vehicles.

Product

Single, Double Power Cord Tester

LX-30A+

-

Shenzhen Lian Xin Technology Co., Ltd.

LX-30A+ - Shenzhen Lian Xin Technology Co., Ltd.

Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .．·used to test single – ends ,double –ends ,three-ends power supply cords.．·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,．·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,

Product

Digital HV Measuring Instruments

Teraohm

-

Metrel d.d.

Teraohm - Metrel d.d.

Advanced, digital HV measuring instrument with maximum test voltage up to 5000v DC and resistance measuring range up to 5 T.

Product

Ultrasonic Hardness Tester

-

Sinowon Innovation Metrology Manufacture Ltd.

Sinowon Innovation Metrology Manufacture Ltd.

◆ Perfect Accuracy——±3% HV, ±1.5HR, ±3%HB.◆ Microscopic Indentation—— Only high-power microscope can observe the indentation.◆ Quick Measurement——Result in 2 seconds.◆ Large LCD Display——Directly display measurement result, times count, maximum, minimal, average and deviation.◆ Friendly Operation——Operate well after short training.◆ Promised Warranty——2-Year warranty for main unit (Excludes Probe).◆ Mass Storage——Save 1000 groups measurement data.◆ Simple Calibration——Save 20 groups calibration data for invoking, improve calibration efficiency.

Product

HV Breakout Modules

-

CSM Products, Inc.

CSM Products, Inc.

The HV Breakout Modules (BM) are specifically designed for safely measuring directly from HV voltage power cables. Currents and voltages are measured directly and the raw data is acquired at up to 2 MHz per channel. With the Vector eMobilityAnalyzer software, which is optimally paired to the CSM HV Breakout Modules, real time power analysis is also possible.

Product

High Voltage Surge Testers

HVST

-

Test Electronics

HVST - Test Electronics

The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.

Product

High Voltage Personal Tester

HV/PT2

-

SURE Engineering cc

HV/PT2 - SURE Engineering cc

HV/PT2 is a compact, affordable, high quality proximity HV tester that is manufactured in South Africa. Your own personal HV tester is now available for you to wear at all times. A five position sensitivity switch enables the user to approach the HV source on the highest sensitivity at a safe distance.

Product

NIM Power Supplies And Bins

-

ORTEC

ORTEC

ORTEC offers two types of power supplies for use with NIM instrumentation: power supplies that provide operating voltages for a detector (more properly called detector bias supplies or “HV” supplies) and power supplies that provide the necessary operating voltages for NIM Modular electronic instruments in the form of a NIM “Bin” with associated power supply.

Product

Ultrasonic Portable Hardness Tester

UCI-3000

-

Qualitest International Inc.

UCI-3000 - Qualitest International Inc.

Advanced Ultrasonic Hardness Tester UCI 3000 applies ultrasonic contact impedance method to do comparative hardness measurement for testing pieces, with the high accuracy, efficiency, portability and easy operation. UCI 3000 is a high-precision portable device for quick measuring hardness of small fogging, cast material, weld inspection, heat affected zone, Ion-nitride stamping dies and molds, forms, presses, thin walled parts, bearings, tooth flanks, etc. It is used for measuring the hardness within the ranges of main hardness scales – HB, HRC as well as HV.

Product

KYK-13 Interface

IP-Crypto

-

Dynamic Engineering

IP-Crypto - Dynamic Engineering

The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.

Product

Horn Antenna

-

Techimp HQ S.r.L

Techimp HQ S.r.L

Horn antenna is a partial discharge sensor designed to receive electromagnetic (EM) emissions from a PD occurring in electric assets like GIS and GIL or MV and HV power transformers. It is a broadband antenna with a flat response which makes Horn antenna suitable in a number of different applications. It has been optimized to operate in a frequency range suitable for PD activity monitoring and it was designed to provide maximum sensitivity and high gain.

Product

Circuit Breaker Analyzers & Timers

CAT Advanced Series

-

IBEKO Power AB

CAT Advanced Series - IBEKO Power AB

DV Power circuit breaker analyzer and timer utilizes the latest technological enhancements for safe and fast testing of circuit breakers. The sophisticated design ensures efficient and reliable operations in high-voltage substations and industrial environments.The CAT Advanced series are stand-alone or PC-controlled digital instruments for a circuit breaker testing. The timing channels record closing and an opening of the arcing, resistor, and auxiliary contacts. Also, the main contact channels can measure the resistance value of the pre-insertion resistors (if present in the circuit breaker).With CAT Advanced series instruments, it is possible to record graphs of open and close coil currents. Furthermore, it records displacements of the HV and MV circuit breaker moving parts. Test results can be saved via USB, PC or be printed via 112 mm (4.4 inches) thermal printer (optional accessory) in tabular and graphical form.A circuit breaker test consists of different operational modes and CAT Advanced series supports:Open (O)Close (C)Reclose (O-0,3s-C)Trip free (CO)O-0,3s-COOpen-Close (O-C)Close-Open (C-O)Open-Close-Open (O-C-O)First trip (O)Multiple operations, such as Open-Close and Open-Close-Open, can be initiated by using a predefined delay time or by sensing a breaker’s contact position.The auxiliary inputs are used to monitor dry and wet auxiliary contacts. The six coil control analog channels measure and record coil currents simultaneously (OPEN and CLOSE), up to 35 A AC/DC.The additional six voltage analog channels have four selectable voltage ranges available (±1 V, ±5 V, ±60 V and ±300 V AC/DC).A built-in micro-ohmmeter generates up to 500A true DC ripple-free current with an automatically regulated test ramp that provides performing static and dynamic contact resistance measurement.Three transducer channels provide a measuring displacement of the circuit breaker moving parts, contact wipe, over-travel, rebound, damping time and average velocity. Also, a user can connect either an analog or a digital transducer to these universal channels.

Product

DC HV tester/ hipot

-

Wuhan Fanke Transformer Manufacture Co., LTD

Wuhan Fanke Transformer Manufacture Co., LTD

1) DC HV tester/ hipot tester/portable-type2) Suitable for DC HV. test or leaking current test

Product

High Voltage Switching System

964i

-

Vitrek Corporation

964i - Vitrek Corporation

The manual method is extremely problematic. Slow, error prone, labor intensive, operator hazardous – don’t even think about recording the test results. The 964i on the other hand, is purpose built to fully automate all of you HV switching needs. You chose the 964i, partnered it with a Vitrek 95X Series Industrial Strength Hipot Tester and QuickTest Pro test automation software. The company wins the Malcolm Baldridge National Quality Award, you get a promotion and that corner office you’ve always wanted. Choose carefully.