Modulation
the varying of amplitude, frequency, or phase.
See Also: Optical Modulation, Modulation Analysis, Modulation Analyzers, Modulation Meters, MER
-
Product
Quad RF Driver
-
The Quad RF Driver contains four independent RF channels, each with an RF synthesizer, variable attenuator, and 1W power amplifier. The RF signal can originate from either the internal synthesizer or an external source via SMA input. All channels have independent frequency, phase, and gain settings and can be operated in one of two modes. The “Wideband” mode operates from 35MHz to 2GHz with a 3.472KHz resolution; over this range the frequency roll-off is approximately 0.5dB/100MHz. “Int-N Phase Adjust” mode allows the user to set and maintain a fixed phase relationship between all four channels. This mode is designed to operate between 300 and 460MHz with a 2MHz resolution. Two additional inputs are provided for an external frequency reference and digital modulation.
-
Product
Analog RF Slot Downconverter: 2000-2400 MHz Input
Model 8111-005
-
The Bandit® Model 8111 provides a series of high-performance, stand-alone analog RF slot downconverter modules. Packaged in a small, shielded enclosure with connectors for easy integration into RF systems, the modules offer programmable gain, high dynamic range and a low noise figure.
-
Product
PXI 4-Slot BRIC Matrix, 264x4 1-Pole (6 sub-cards)
40-562B-021-264X4
Matrix Switch Module
The 40-562B-021-264X4 is a high density BRIC4 matrix module with a size of 264x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
LXI High Density 160x16 2A Matrix
60-554-005
Matrix Switch Module
A high-density single pole matrix module capable of switching up to 300VDC/250VAC, 2A (60W max). The use of high-quality electro-mechanical relays offers high switching confidence for signal routing in large ATE systems.
-
Product
Ethernet Communications
-
Campbell Scientific offers complete Ethernet connectivity solutions for our data acquisition needs. Data loggers are available with integrated Ethernet, as well as stand-alone Ethernet modules.
-
Product
Xeon E5 Processor AMC, 40 GbE, PinoutPlus™
AMC751
-
The AMC751 is a Processor AMC (PrAMC) in a double module, full-size AdvancedMC (AMC) form factor based on the Intel® Xeon E5-2648L v4 which has 14 Cores @ 1.8 GHz. The module follows the AMC.2 and AMC.3 specifications.
-
Product
Ethernet/InfiniBand Switch
VPX6-6802
-
Curtiss-Wright Defense Solutions
The VPX6-6802 is a combined Data Plane and Control Plane high-performance switch for small, mid-size and large 6U VPX systems. As part of the Curtiss-Wright Fabric40™ family of high-speed VPX modules, the VPX6-6802 6U OpenVPX Ethernet & InfiniBand Switch provides centralized switching functionality for HPEC systems and supports both Ethernet and InfiniBand protocols on the Data Plane.
-
Product
Rectifier/Modular PSUs
-
The rectifier families are housed in either 19" racks or provided as compact modules. The rack mounting rectifiers are aimed at telecoms applications. This range of robust rectifiers start at 250W and have a life time of more than 8 years and an MTBF of over 50 years. For even greater security these hot swap modules can be configured to provide a redundant DC output. Up to 2 additional AC inputs with automatic switchover are provided on a number of these telecoms rectifiers.
-
Product
Datalogger
iLOGPlus
-
Infinite Industrial Informatics Lt
iLOGPlus RTU/Data Loggers are internet enabled devices, specially suited for remote data acquisition, distributed telemetry and remote control. The units act as master devices and send alerts and data files on their own via FTP, email and SMS. All types carry a built-in TCP/IP webserver with live webpages that can be accessed by any Internet browser application. They accept and serve TCP and SMS commands for interactive operation in a SCADA system.Analog inputs and digital I/O are expandable by means of I/O expansion modules, plugging on a serial I/O expansion bus.
-
Product
PXI 13 x DPDT Power Relays
40-130-102
Relay
Pickering Interfaces 40-130 DPDT Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. It is available in a choice of 8 and 13 relay versions and has voltage handling up to 220VDC/125VAC and current handling to 2A . Connections are made via a front panel mounted 50 or 78 pin D-Type connector.
-
Product
NI TB-2645B Terminal Block for NI 2532B as 1-Wire Dual 16x16 Matrix or 2-Wire 16×16 Matrix Topology Without Column Protection Resistors
782385-11
Terminal Block
The TB-2645B provides the necessary routing to configure the PXI-2532B or PXIe-2532B PXI Matrix Switch Module as a 2-wire 16x16 or 1-wire dual 16x16 matrix. You can directly connect the TB-2645B to the front panel I/O connectors of the PXI-2532B or PXIe-2532B. This terminal block includes ribbon cable headers to connect signals to the PXI Matrix Switch Module. The TB-2645B also provides optional isolation resistors to protect the reed relays from capacitive loads.
-
Product
PXI Expandable 16x16 RF Matrix 50Ohm Lemo 00
45-720A-541
Matrix Switch Module
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
10-Ch Pneumatics CAN without RCV module
YAV90PNF
CAN Interface
This pneumatic subsystem is the same as YAV90PNE, but without the VPC receiver module integrated, making it a good option to be used inside the fixture. Since the control is CAN, user can easily place electrovalves inside the fixture without the need to use a bunch of wires.
-
Product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
RF Signal Generator
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Multi Protocol 4000 Modules
-
The M4K module can be one of many protocols that is used on a variety of platforms for the 4000 Multi Protocol Board.
-
Product
LXI Dual 75x4 2-Pole HV Matrix
60-311-002
Matrix Switch Module
The 60-311 is a 2-pole Matrix Module available with one, two or three separate 75x4 matrices housed in the same case. It is capable of cold switching 750VDC continuous with a carry current of 2A plus higher pulse conditions e.g. typically 1000VDC for 1s with low duty cycle or 6A for 200us with <1% Duty Cycle.
-
Product
PXI 2 Slot BRIC 45x16 1-Pole (3 sub-cards)
40-561A-221-45X16
Matrix Switch Module
The 40-561A-221-45X16 is part of a range of high-density PXI BRIC matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
Product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 4-Banks
41-670-001-AABBCC
Simulator
The 41/43-670-001 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Product
Modular Cards
SET 14XX
-
The carrier boards from the SET Modular Card 1415 / 1416 / 1417 series offer slots for 8 functional/measuring modules from the SET “SMARTbrick” series.
-
Product
Signal, Module, ITA, TriPaddle, 90 Series, 64 Position, with Right Angle Contacts
510108112
ITA Module
Primary mating module 510104134. (May mate with other Receiver modules, as well.)
-
Product
SparkFun Transceiver Breakout
NRF24L01+
-
This module uses the newest 2.4GHz transceiver from Nordic Semiconductor, the nRF24L01+. This transceiver IC operates in the 2.4GHz band and has many new features! Take all the coolness of the nRF2401A and add some extra pipelines, buffers, and an auto-retransmit feature - very nice!
-
Product
PXIe-6355, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module
783632-01
Multifunction I/O
PXIe, 80 AI (16-Bit, 1.25 MS/s), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6355 offers analog I/O, digital I/O, and four 32‑bit counter/timers for PWM, encoder, frequency, event counting, and more. The device delivers high-performance functionality leveraging the high-throughput PCI Express bus and multicore-optimized driver and application software. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6355 is well-suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-033-HI
Programmable Resistor Module
The 40-230-033-HI (PXI) and 42-230-033-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 3.5Ω and 52.4kΩ with 1Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
cDAQ-9181, 1‑Slot, Ethernet CompactDAQ Chassis
781496-01
Chassis
1‑Slot, Ethernet CompactDAQ Chassis - The cDAQ‑9181 is a CompactDAQ Ethernet chassis designed for small, distributed sensor measurement systems. The chassis controls the timing, synchronization, and data transfer between C Series I/O modules and an external host. You can use this chassis with a combination of C Series I/O modules to create a mix of analog I/O, digital I/O, and counter/timer measurements. The chassis also has four 32‑bit general‑purpose counters/timers. You can access these counters through an installed, hardware‑timed digital C Series module for applications that involve quadrature encoders, PWM, event counting, pulse train generation, and period or frequency measurement.
-
Product
200 Pin D Cables - 200 Pin to Alternative Connector for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 200-pin D connector.
-
Product
Inputs Temperature Data Logger – Pt100
HD32.7
-
The instrument HD32.7 is a robust 8 inputs data logger for Pt100 sensor temperature probes. The probes can be Pt100 with SICRAM module, direct 4-wire Pt100 or direct 2-wire Pt1000.
-
Product
Flow Battery Test Stations
-
Greenlight's turn-key flow battery test systems include load/power supply modules, automated control of flow, pressure and temperature of electrolyte fluids, cell voltage monitoring, 3-level safety system and computer with Emerald dynamic automation software. All Greenlight flow battery test systems come with a our standard 1 year warranty. Our customer service team is available to travel to your facility for commissioning and training.Greenlight''s Automation Division also offers flow battery assembly equipment.
-
Product
External Input Module
EIM-01
-
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
Product
Camera Module Socket
-
Designed for application to all SMD type products, compact camera module clamshell socket provides a connector clip embodying precision in contact, a total interface solution.
-
Product
Interface Board, 16:1 USB
40-965-909
Interface
Converter card for 40-737-001 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 16 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 16 USB1 or USB2 signals.
