Interconnects
Links between systems, networks,nodes, equipment, devices, components and circuits.
See Also: Mass Interconnect, Connectors, Cable Assemblies, Interfaces
-
Product
CorLogic PLC
-
Created to meet the demands of Industry 4.0, this IIoT-ready PLC is the perfect equipment to interconnect your machinery, systems, and cloud smartly, deploying performance and connectivity in a very cost-effective device.With large processing capabilities, smart I/O, and support for a wide variety of communication protocols.
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMCSK-04-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/cd
M8091BSCB
-
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
Product
Pulse generator
9355-1
-
Solar Model 9355-1 Pulse Generator is designed to provide impulse excitation by means of an injection probe placed around interconnecting cables or power wires. The unit uses a charged transmission line (50 ohms) to generate a pulse with less than 2 nanoseconds rise and fall time, and duration of approximately 30 nS, calibrated in a 50 ohm fixture to deliver up to 5 amperes at a rate of 30 p.p.s. for one minute as required by MIL-STD-461D/E, test method CS115.
-
Product
Low Noise Pre-Amplifiers
-
Low Noise Pre-Amplifier and companion external low noise amplifier (LNA) are used to amplify low level microwave signals. The Pre-Amplifier contains an AC/DC power supply, internal low noise amplifier, and a bias tee to source a DC bias voltage on the RF input connector.To overcome cable loss between the test antenna and the Pre-Amplifier assembly, a remote low noise amplifier (LNA) is mounted directly onto the 10 GHz antenna. A bias tee inside the Pre-Amplifier chassis powers the remote LNA through the coax cable interconnecting the pre-amplifier and the 10 GHz test antenna.
-
Product
Test Services
-
D-Coax offers RF/Microwave test services for your researchprojects, as well as, production quantities tests. We have available resources and expertise in the high frequency interconnects testing that will benefit your research and products. We will work with you to make your requested tests the most accurate and reliable and we'll complete them in a timely fashion. The following parameters can be characterized or tested to specifications with our test services: Time Domain: Impedance, Impedance profile, rise time, propagation delay, skew and more. Frequency Domain: S21 - Insertion loss, S11- Return loss, S12 - Reverse Insertion loss (port 2 insertion loss), S22 - Reverse Return loss (port 2 return loss) and more.
-
Product
Local-Area Networks
-
Schweitzer Engineering Laboratories, Inc.
LAN products support the interconnection of devices in one location to exchange data
-
Product
18-Port PCI Express
PEX 8733
-
The ExpressLane™ PEX 8733 is a 32-lane, 18-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8733 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
Functional Test
xUTS
-
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
Product
Interconnect Adapters
-
Interconnect Adapters funnel wiring from modules to a VXI card. The adapter has removable side, top and bottom plates. Connector cover plates and cable clamps are ordered separately.VPC VXI adapters have been re-engineered to eliminate the need for punching holes in certain manufacturers cards. This design uses a clip that clamps down on the card's existing ejector tabs which firmly fastens the adapter to the card.
-
Product
Time Domain Reflectometers
HL1100 Series
-
HYPERLABS HL1100 Series TDR instruments provide high-performance test and measurement capabilities for use in the field or in the lab. These instruments are used for applications such as fault detection in cables and interconnects, impedance characterization, time of flight analysis, water level measurement, and more.
-
Product
Digital and Analog Test Sets
-
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
Product
OpenVPX Cable Solutions
OPENVPX-CABLE
-
Compliant to VITA 46 and 65, the cabling assemblies are ideal for development. They can be used for I/O to bulkhead connectors and slot-to-slot connections. Front-plug versions allow testing across the backplane or full interconnect path.
-
Product
Signal Integrity TDR and VNA Software
80SICON IConnect
-
IConnect software is the efficient, easy-to-use, and cost-effective solution for measurement-based performance evaluation of gigabit interconnect links and devices, including signal integrity analysis, impedance, S-parameter and eye diagram tests, and fault isolation.
-
Product
Modular Multilevel Converter (MMC) Test Bench
-
Research into innovative HVDC interconnections and FACTS applications requires a flexible hardware architecture that allows testing of new topologies and switch configurations.
-
Product
Signal Path Analyzers
HL2200 Series
-
HYPERLABS HL2200 Series Signal Path Analyzers™ provide high-performance test and measurement capabilities for a fraction of the cost of traditional benchtop systems. These differential, multi-channel instruments are ideal for interconnect characterization, debugging cable assemblies, coupon testing, controlled impedance analysis, and other applications requiring a fast rise time.
-
Product
Switch & Router Modules
-
Curtiss-Wright Defense Solutions
Our highly engineered networking cards provide systems integrators with a fast and powerful way to interconnect chassis, cards, and CPUs through switched Gigabit, 10 Gigabit, and 40 Gigabit Ethernet. Operating at wire-speed, Ethernet switching and routing can be used to architect the infrastructure for unified (Ethernet only) or hybrid (Ethernet control and other switched data-plane fabric) networks for transferring IP-based control and data packets within advanced military systems.
-
Product
Passive Oscilloscope Probes
5900 SERIES
-
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
Product
Modular Contacts
-
Bourns Modular Contacts are off-the-shelf interconnect devices that can be used in cellular telephones, PDAs, laptop computers, portable medical and test equipment, anywhere a rechargeable battery pack is required.
-
Product
Signal Conditioners
-
Omega's modular signal conditioners provide a low-cost, high-performance method of inter-connecting real-world analog signals with data acquisition, monitoring, or control systems.
-
Product
DC Coupled Differential Switching System
BS1553F(X)
-
Universal Switching Corporation
The BS1553F(X) is a modular passive DC coupled differential switching system. It is designed as an automated "patch panel" for interconnecting numerous MIL-STD-1553 devices, cables and hardware, or for routing other differential signals such as '422 clock/data or kelvin ATE measurements. The I/O capacity is scalable from a small 8x8, up to 64x64 in one 5RU unit.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
-
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
High Power Rack And Panel Connectors
LSH Series
-
The LSH rack and panel connectors include leading-edge Hypertac® hyperboloid technology. The Polyphenylene sulfide (PPS) insulators interconnect technology ensures LSH connectors are easy mating. The LSH Series delivers customers a high life cycle.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 110 dB, 10 dB steps
8496A
-
The Keysight 8496A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 110 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 6 or 10 Positions Blocks, UUT 456 x 320 mm
MG-07-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 456 x 320 mm (wxd)• Outer dimensions: 620 x 589 x 100 x 184 mm (wxdxh1xh2)• Equipped with dedicated cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
-
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
6-Port PCI Express
PEX 8624
-
The ExpressLane™ PEX 8624 device offers 24 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 6 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The 24-lane switch enables users to add scalable, high bandwidth, non-blocking interconnection to a wide variety of applications including workstations, communications, storage, and embedded systems as well as intelligent I/O modules and add-in cards.
-
Product
WAVEPULSER-40IX + WAVEPULSER-SI-STUDIO-NRZ + Adaptors and Calibration Kit
WAVEPULSER-40iX-BUNDLE
-
High-speed Interconnect Analyzer, 4-port, S-par @40 GHz, <1 mm Res., 4 phase matched cables, bundle.
-
Product
CompactPCI Chassis
-
CompactPCI is a standard in computer bus technology for industrial computing that utilizes a Eurocard type connector combined with PCI signaling and protocols. cPCI boards come in 3U and 6U variants and are typically interconnected through a passive backplane. The connector pin assignments are standardized by PICMG , allowing for eight boards in a PCI segment with multiple bus segments being allowed with the use of active bridges.
