Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
Serial RS-232 Expansion Connector Accessory for USBHub3c
-
Used for connecting a serial RS-232 interface to the control the USBHub3c through the expansion interface connector. Screw terminals are provided for the RS-232 interface. While this board provides for wiring connections, a host machine external to the USBHub3c is required for this control interface.
-
Product
PCI/PCIe-Based Serial Communications Cards
PCI-C588/PCI-C584/PCIe-C588
-
- IRQ & IO address automatically assigned by BIOS- Supports up to 2 cards per system, jumper-less, easy to configure- Isolated RS-422/RS-485 interface (C422/C485, C518/C514)- PCI Rev 2.1 Plug-and-play- PCI Express® x1 compliant (PCIe-C588)
-
Product
PCIe-8431, PCI Express, 16-Port, RS485/RS422 Serial Interface Device
780592-02
Serial Interface
The PCIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
GPIB Serial Interfaces
-
ICS's GPIB Serial Interfaces provide a mix of RS-232 and RS-422/RS-485 asynchronous signals to drive serial devices. Interfaces are available for transparent data transfer and with smart firmware that adds an IEEE-488.2 Interface to plain serial devices or with embedded PC boards. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
3U CompactPCI Serial 4-slot SSR w/ RTM w/ Ethernet
1CPCIS-304-R210
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot right, with rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, with connectors for Rear Transition Modules (RTMs) in slots 1 to 3, Ethernet full mesh.
-
Product
3U CompactPCI Serial 4-slot SSL w/o RTM w/ Ethernet
1CPCIS-304-L200
-
3U CompactPCI Serial Backplane with 4 CompactPCI S.0 slots, system slot left, without rear IO : 1x CompactPCI S.0 CPU slot, 3x CompactPCI S.0 peripheral slots, without connectors for Rear Transition Modules (RTMs), Ethernet full mesh
-
Product
Conduction Cooled XMC Interface Board with PCI Express Host Interface, Supporting up to 4 PX Modules, 2 RTx 5 Channel Modules, 1 Discrete & 1 Serial Module
EXC-8000ccXMC
-
The EXC-8000ccXMC is part of Excalibur’s 8000 family of multiprotocol boards. This conduction cooled XMC interface board has a PCI Express host interface and supports up to 4 Px modules, 2 RTx 5 channel modules, 1 Discrete and 1 Serial module. Due to the constraints of the XMC specification the modules are integrated onto the board itself rather than as physically separate modules.The EXC-8000ccXMC supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from modules that support DMA, with much less CPU overhead than when not using DMA.
-
Product
Ethernet To Modbus RTU Interfaces
-
ICS's Ethernet to Modbus Interfaces provide Modbus TCP/IP to Modbus RTU serial conversion and Raw Socket (Telnet) to control Modbus RTU Slave Devices. Available in small Minibox™ and OEM board formats. OEM board has Ethernet, GPIB and USB interface ports. All Interfaces include the VXI-11 protocol for use with: LINUX, UNIX, SunOS, Apple OS X, HP-UX, IBM-AIX and Windows 2K or later Windows systems.
-
Product
Functional Testing and Test Engineering
-
Customer-supplied or developed in-house• Ruggedization of existing (lab-built) fixtures• Co-develop hardware/software• Deployment, implementation, and training• Engineering evaluation tools• Design verification• Medical device evaluation• Manufacturing test systems• Verification test systems• Go/No-go tests• Serialization, recordkeeping, and datalogging• Troubleshooting failed units with other test platforms
-
Product
Engine Control
StepGenerator4
-
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
Product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
Single Board Computer
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
Product
Digital I/O Adapter Module For FlexRIO
Digital I/O Adapter
Digital I/O Adapter Modules for FlexRIO offer up to 54 channels of configurable digital I/O that can interface with single‐ended, differential, and serial signals at a variety of voltage levels. When combined with a large, user‐programmable FPGA, you can use these modules to solve a variety of challenges, from high‐speed communication with a device under test to emulating custom protocols in real time.
-
Product
Rugged PC Compatible
SYS-405D
-
The SYS-405D is a rugged, industrial system capable of operating at extended temperatures without requiring a fan or heat-pipe. The SYS-405D is based on the dual-core Intel® Atom™ E3827 processor and protected by a rugged enclosure.The SYS-405D includes dual Ethernet, dual MiniPCIe, USB 3.0, serial ports with RS-232/422/485 and two independent displays via DisplayPort, and/or Analog VGA
-
Product
Modular I/O via Ethernet
2601 Series
-
100/10 Mbps Ethernet gateway to 2600 series I/O modulesFour RS-232/422/485 ports for remote serial devicesIntegral support for interlock and emergency stop circuitsNetwork watchdog shuts off I/O upon client faultHigh-performance network stack: up to 1000 transactions/secondUltra-fast, one second boot-up timeOptically isolated serial communication to I/O modulesWatchdog TimerCE CompliantCompatible with Linux and Windows
-
Product
6U VPX FPGA Cards
-
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters.
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
Fault Insertion Unit
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
Bit Error Rate Testers
-
The Tektronix BERTScope® and PatternPro® families provide a range of signal conditioning and BER test solutions from 1.5 Gb/s to 40 Gb/s on 1-4 channels and deliver the test and measurement industry’s broadest serial communications test portfolio of Bit Error Rate Tester products.
-
Product
1-Channel 3.6 GHz or 2-Channel 1.8 GHz 12-bit A/D with DDC - 3U VPX
Model 52741
-
- Ideal radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- One-channel mode with 3.6 GHz, 12-bit A/D- Two-channel mode with 1.8 GHz, 12-bit A/D- Programmable one- or two-channel DDC (Digital Downconverter)- 4 GB of DDR3 SDRAM- µSync clock/sync for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration ManagerSynchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
Product
Low Profile PCI Express 1-Port
7106e
-
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
Serial Link Analyzer
HOTLink
-
The HSLA is a low-cost data recorder and diagnostics tool for 8B/10B encoded HOTLink systems. Each HSLA is preconfigured for a specific link speed (between 160Mbps to 1.0625 Gbps), and a connector type - copper (BNC, FCN, or SMA) or optical. The HL2View software makes data capture and analysis quick and easy.
-
Product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
170MHz 4-Channel DDS Signal Generator
409B
-
The 409B generates four independent, phase synchronous sine wave output signals and is programmable in 0.1 Hz steps from 0.1 Hz to 171 MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. Internal memory can store a sequence of settings. The -AC option is available to enable users to step through settings using an external trigger. It is accurate to 1.5 ppm using the on board TCXO timebase or you can use an external timebase, There is also a /R option that provides a way to lock to and track an external 10MHz frequency input. A line powered AC adapter and SOF8_409 windows software on a CD are included.
-
Product
Multi-Axis Stage Controller
MS-2000-WK
-
Applied Scientific Instrumentation
*100 MHz Microcontroller for faster command processing and servo control.*Closed-loop DC servo control of up to four motorized axes.*Firmware upgradeable via serial connection.*0-10V DAC for single piezo axis control.*Remembers last position on power down/up.*LCD display shows axes coordinates and status.*"Zero" and "Home" buttons for simple stand-alone operations.*USB or RS232 serial control with baud rates to 115200 Baud.*Compact ergonomic tabletop control unit 6"D x 9"W x 3"H (16 x 23 x 9 cm).
-
Product
Low Profile PCI Express 2-Port
7202ec
-
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
PXIe-5831, 44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver
786853-01
Vector Signal Transceiver
44 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5831 supports validation and production test into mmWave frequency bands. The PXIe-5831 incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe‑5831 combines fast measurement speed and the small form factor of a production test box with the flexibility and high performance of R&D-grade box instruments, making it an ideal solution in both the lab and the production floor. The PXIe-5831 meets the stringent challenges of 5G New Radio, but it is also able to test a variety of cellular and wireless standards such as Wi-Fi 6. In addition, you can easily expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
Product
C/D-PHY CSI-2/DSI Analyzer
Envision X84
Analyzer
is the first combination C-PHY/D-PHY analyzer in single platform. The Envision X84 supports C-PHY/D-PHY and Cameral Serial Interface (CSI-2) and Display Serial Interface (DSI/DSI-2) on a single hardware platform. Envision X84 supports C-PHY version 1.1 and D-PHY 2.1 as well as CSI-2 version 2.1 and DSI version 1.3 and DSI-2 version 1.1. The Envision X84 offers Silicon ad device designers, integrators and validation engineers a complete, robust yet flexible tool to ensure the correct and efficient operation of Camera and Display over C-PHY and D-PHY implementations.
-
Product
PXIe-6593, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument
785976-01
Serial Interface
PXIe, 16 Gbps, 8-Channel PXI High-Speed Serial Instrument - The PXIe‑6593 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex Ultrascale FPGA to implement various high-speed serial protocols, and it is … programmable in LabVIEW FPGA for maximum application-specific customization and reuse. The PXIe‑6593 takes advantage of FPGA multigigabit transceivers for up to eight TX and RX lanes.
-
Product
10RJ11-DB25M Serial Cable for 4-Port Serial Board to a DB-25 Male Connector
182846-01
Serial Cable
Serial conversion cable for 4-port serial board to a DB-25 male connector.
-
Product
SparkFun FTDI Basic Breakout
Beefy 3
-
This is SparkFun Beefy 3 FTDI Basic Breakout for the FTDI FT231X USB to serial IC. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards. It can also be used for general serial applications. Built upon the same foundation as our 3.3V SparkFun FTDI Basic Breakout, the Beefy 3 is equipped with an AP2112K voltage regulator making this FTDI basic breakout board capable of handling a current load of up to 600 mA! With the addition of a more "Beefy" voltage regulator your will now be able to power a 3.3V project directly from the FTDI. The pinout of this board matches the FTDI cable to work with official Arduino and cloned 3.3V Arduino boards.
-
Product
PXI FPGA Board
PXIe-8316-DSP
-
The PXIe-8316-DSP FPGA board is a user programmable hardware platform with an 8-lane Gen3 PXI Express (PXIe) interface. It includes four QSFP ports (16 lanes) to support High Speed Serial (HSS) connections.
