Solid State Relays
-
Product
Low Thermal EMF Relays
Series 100
-
The Pickering Series 100 is a complete range of Single-in- Line (SIL) reed relays primarily intended for direct drive from 4000B CMOS or similar low current sources. They feature a very low level of thermal EMF.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
1.75 (44.45) 24" Solid Panel
P-0124
-
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. , A multi-step painting process is used to paint the panel - the finish is textured unless otherwise specified.
-
Product
PXI Single Microwave SPDT Relay 18GHz 50 SMA - External Termination
40-781-121
Relay
This single microwave SPDT relay module is part of the 40-781 range that consists of one or two changeover switches capable of switching frequencies to 18GHz in 50 Ohm. Versions are available with either internal or external terminations and connections are made via front panel mounted high quality SMA RF coaxial connectors.
-
Product
19.25 (488.95) 24" Solid Panel
P-1924
-
Special grade .125” sheet aluminum (5052-H32 EPS). Each side, edge and corner is carefully de-burred and chamfered to provide a flawless finish, resulting in a superior quality panel. Finish is textured unless otherwise specified.
-
Product
Microcomputer Three-phase Relay Test Set
-
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations.
-
Product
Micro SIL Reed Relays
Series 108
-
SIL relays - 0.15 inch wide packages. Requires a board area of 0.15 x 0.8 inches (3.8mm x 20.3mm). 10 Watts Form A or 3 Watts Form C switches in Mu-metal package
-
Product
Relaying Protection Tester
GDJB-III
-
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
1. DC voltage relay test2. DC current relay test3. AC voltage relay test4. AC current relay test5. High current injection6 Time counter in relay test
-
Product
4 Relay Channels, Latching
RY2
-
The RY2 module features 4 individual single-pole, user SPDT Form C (changeover/break-before-make type) relays (channels). Each channel has a common input terminal (C), a normally closed output terminal (N/C), and a normally open (N/O) output terminal. The channel either energizes or de-energizes the relays (close or open) so that the signal provided on (C) may be switched/directed to either the (N/C) or (N/O) terminals.
-
Product
8-CH Relay Outputs & 8-CH Isolated DI Card
LPCIe-7250
Relay
LPCIe-7250 provides 8-CH SPDT (Form C) relay outputs and 8-CH isolated digital inputs. The status of each relay output is represented by an onboard LED. When the relay is in SET condition, its corresponding LED will turn ON, and on the contrary, it is OFF. All digital input channels are non-polarity, optically isolated, and may be set to use RC filter or not. The devices are suitable for collecting digital inputs in noisy environments.
-
Product
Digital Total Dissolved Solids Pen (TDS)
CD600
-
The Milwaukee CD600 Total Dissolved Solids (TDS) Pen is designed for hydroponics, aquariums, horticulture, water conditioning and many other applications. The CD600 helps you make sure that your plants are receiving the right amount of nutrient or helps you keep your filters up-to-date and clean for water filtration. Keep TDS in your target range to help your achieve better results.
-
Product
19" Solid Fixed Storage Shelf, 24"D
SS-1924
-
Sturdy 19" shelf formed of one piece of 16 ga. CRS bolts to panel mounting rails. Supports heavy chassis or power supplies or provides storage for tools, test leads, chart paper, etc.
-
Product
PXI 6U Power Relay Module
-
The SPDT Power Relay Module consists of 48 single pole changeover relays controlled by a PXI/CompactPCI interface. It is suitable for applications were conventional reed-relay based switching modules do not have sufficient voltage rating or current carrying capacity. All 48 contacts are electrically isolated from each other and are capable of switching resistive and inductive loads up to 2000VA at 240V AC. The module is built on a single width 6U PXI module and the interface is via a standard PXI/CompactPCI backplane. Connection to the switching contacts is via three 50-pin D-type male connectors mounted on the front panel. These are machined contact types with 7.5A current carrying capacity.
-
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Dynatrol® Level Switch for Low Density Bulk Solids
CL-10GS
-
Dynatrol® GS Level Sensor Detector is designed for application to high, intermediate, or low point level detection of bulk solids. The GS Level Detector successfully handles lightweight media applications that are difficult to measure or detect like fine low density powders, flock, fluff or fumed silica, etc.The CL-10GS is typically used with bulk solids in the density range of 5-10 lbs/ft3.
-
Product
16 Channel, 1 Form A 15A Relay Switch
DP-cPCI-4545
-
The DP-cPCI-4545 is a 16 channel relay switch module. It is constructed using 1 Form ‘A’ relays. It provides 500V DC isolation between channels.
-
Product
Single Phase Relay Tester
PTE-50-CE Pro
-
This electronic, independent source can be adjusted in amplitude, frequency, and phase angle. It comes installed as standard with the ‘Pro’ versions of the PTE sets, but it can also be purchased separately and mounted by the user inside the unit’s lid in a few minutes.
-
Product
PCI General Purpose Relay Card, 16xSPDT, 2A
50-131A-001
General Purpose Relay Module
The 50-131A-001 16xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
Transmitter System for Low Signal Power Relay Stations
AM3000 Series
-
Japan Communication Equipment Co., Ltd.
This system is a minimal low signal power transmitter for the relay of ISDB-T Digital Terrestrial Broadcasting. As the need arises, it's possible to have the compensation function built-in for integrate-type basic equipment.
-
Product
Relay Software
-
Megger’s advanced relay testing software is designed to make the complex task of relay testing simpler. Intuitive colour screen graphics with a vast library of digital and electromechanical relay routines from relay manufactures across the world.
-
Product
ASI/SD-SDI Input+output With Relay Bypass For PCIe
DTA-2145
-
General-purpose DVB-ASI input and output, also SD-SDI capable. A relay automatically connects input port to output port upon software- or hardware failures, enabling highly-available system configurations without requiring a failover switch.
-
Product
Universal relay test set and commissioning tool
CMC 356
-
The CMC 356 is the universal solution for testing all generations and types of protection relays. Its powerful six current sources (three-phase mode: up to 64 A / 860 VA per channel) with a great dynamic range, make the unit capable of testing even high-burden electromechanical relays with very high power demands.
-
Product
PXI/PXIe Solid State Attenuator, Hex, 6GHz, 50Ω, SMA
43-182B-006
Attenuator
The 41-182B-006 (PXI) and 43-182B-006 (PXIe) are programmable RF attenuator modules with 6 channels in 2 slots capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuator uses solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 50 GHz, 50 Ω, SMA-2.4, Failsafe
42-780B-553
Relay
The 40-780B-553 (PXI) and 42-780B-553 (PXIe) are triple failsafe SPDT 50 GHz unterminated microwave relay modules. The 40/42-780B range is available with one, two, three or four SPDT switches capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via front panel mounted high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions are also available which can support up to three SPDT relays in a single slot.
-
Product
Mechanical Power Relays (2A Or More)
-
Panasonic Industrial Devices Sales Company of America
Panasonic's Mechanical Relays with greater than 2A nominal switching capacity and comes in polarized and non-polarized types. Panasonic has a wide range of switching capacities up to 120A AC and 300A DC, with various contact arrangements and sizes. Panasonic also has Power Relays with low coil holding capability for lower power consumption.
-
Product
Relay I/O Modules
XTA Series
-
These modules are intended for use with BusWorks XT Series discrete I/O or other digital output modules for the purpose of driving high energy loads.
-
Product
Safety Relay Modules & Sensors
-
Using safety relay modules, you can reliably implement safety functions in machines and systems. They monitor signals from emergency stop buttons, light grids, and safety door switches, and initiate a safe state where necessary.
-
Product
PCI General Purpose Relay Card, 26xSPDT, 2A
50-131A-002
General Purpose Relay Module
The 50-131A-002 26xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
High Voltage Dry Reed Relays For up to 15 kV
SERIES 62 & 63
-
ungsten switches with power rating of 50 Watts maximum? Three switch types:5kV stand-off, 3.5kV switching10kV stand-off, 7.5kV switching15kV stand-off, 12.5kV switching? Series 62 has push-on connectors on top face for EHT and solder pins and nylon studs on the underside for PCB mounting
