Wave Solder
-
Product
68-Pin VHDCI Connector, Slimline - Male, Solder
C068VMR-6SB-6A
-
This slimline version of the VHDCI connector is designed to allow users to directly terminate a cable with soldered connections to the 68 Way VHDCI connector. It is difficult to terminate cable to the 68 pin VHDCI because of the high density and fine pitch. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
Soldering Station
SM-898D
-
*Using micro-processor PID program control technology, precise dual digital display hot air gun and the stability of the actual temperature of the soldering iron, fast automatic temperature compensation feature further enhanced temperatures.*The amount of wind, air flow, temperature soldering iron are adjustable.*The air gun holder is a magnetron (or light control), holding the handle when the system will automatically enter the working mode; handle is placed on the shelf when the system enters standby mode automatically.(One more than the 898D Auto Sleep off function)*System with automatic cold wind function, can prolong the life of the heating element.*This product uses "brushless fan" as a source of air, reduce noise, improve work efficiency
-
Product
Mini Coax, Contact, ITA, RG316 & 178, Solder Sleeve
610103158
Coax Contact (ITA)
Contact, ITA, Mini Coaxial, RG316 & 178, 50 MAU, Solder Sleeve
-
Product
25-Pin D-Type Female Solder Bucket
92-960-025-F
-
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Millimeter Wave Control Devices
-
Ducommun millimeter wave products include various control devices for system integration. The CAE, CPS, CPD and CPM series control devices are discrete or MMIC based PIN diode attenuators and switches. The CAF, CAL, CAR and CPL series control devices are waveguide based mechanical tunable attenuators and phase shifters. These devices are offered to cover the frequency range from 18 GHz to 110 GHz.
-
Product
Traveling Wave Fault Locator
XC-2100E
-
XC 2100E, a Fault Location System based on principle of travelling wave detection is the solution to above problem. It can detect not only permanent fault, but also transient fault within one tower span accuracy (with best accuracy of ±50 meters). It is a kind of Line Monitor for continuous monitoring of transmission lines and gets triggered whenever travelling waves are generated on line due to switching, lightening or fault.
-
Product
68-Pin Micro-D Male Solder Bucket
40-962A-068-SB-M
-
This connector is designed to allow users to directly terminate with soldered connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
37-Pin D-Type Male Solder Bucket
92-960-037-M
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Wave and Tide Sensor
-
Aanderaa Wave and Tide Sensors are compact fully integrated sensor for measuring the wave and tide conditions designed to be mounted on the Aanderaa multiparameter SeaGuard Platform or via cable connected to SmartGuard datalogger.
-
Product
Dual Projection 3D In-Line Solder Inspection System
KY8030-2
-
The new KY8030-2 delivers 2x fasterinspection without compromising performanceand accuracy.Using patented dual projection, the systemeliminates the critical Shadow problem thatall 3D SPI systems can be vulnerable to.Easy UI and SPC Plus are included in the systempackage in order to help users achieve faster& easier printer process optimization
-
Product
Replacement Solder Tip Leadset for Use with D410/D610
Dx10-SI-HiTEMP
-
The 90 cm HiTemp cables and Solder-In lead can be used for controlled situations where the differential amplifier module needs to be removed from the extreme temperature environment. Ideally suited for testing scenarios where the temperature can fluctuate from -40 °C to +105 °C.
-
Product
Millimeter Wave Products
-
Reliable Millimeter-Wave High-Power Products for Airborne, Maritime and Ground Mobile Deployment
-
Product
01 With Soldering Eyelets | 10 Positions | M6
01-1xxx-00/30xxx-10-M
-
Multi wafer compact selector with 36° detent angle, 3 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
2-26.5 GHz Traveling Wave Amplifier
1GG7-8045
Amplifier
The 1GG7-8045 is a broadband GaAs MMIC Traveling Wave Amplifier designed for high output power and moderate gain over the full 2 to 26.5 GHz frequency range. Seven MESFET cascode stages provide a flat gain response, making the 1GG7-8045 an ideal wideband power block. Ebeam lithography is used to produce gate lengths of ~0.3 mm. The 1GG7-8045 incorporates advanced MBE technology, TiPtAu gate metallization, silicon nitride passivation, and polyimide for scratch protection.
-
Product
Lo-PRO®file Collet Socket with Solder Tail Pins
Series 513
-
LO-PROfile Collet Sockets with Solder Tail Pins. Features: LO-PRO file Collet Sockets are available with solder tail or wire wrap pins. Consult Data Sheet No. 12012 for wire wrap pins. Choose from several size and plating options
-
Product
50-Pin D-Type Male Solder without Backshell
92-960-050-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections. 50-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module.
-
Product
Pulsed And CW ESR/EPR: Quasi-continuous Powerful Millimeter (mm-wave) And Sub-millimeter (sub-mm Wave) Orotron Generator
-
Insight Product Company offers Quasi-continuous powerful millimeter (mm-wave) and sub-millimeter (sub-mm wave) Orotron Generators which can be used for both continuous wave (CW) and pulsed electron spin resonance (ESR) and electon paramagnetic resonance (EPR) experiments.
-
Product
HD Arbitrary Waveform Generator,8 Ch,350 MHz,16 bit,128Mpts/Ch,6 Vpp output,AFG/AWG, Wave Sequencing
T3AWG3358
Arbitrary Waveform Generator
HD Arbitrary Waveform Generator,8 Ch,350 MHz,16 bit,128Mpts/Ch,6 Vpp output,AFG/AWG, Wave Sequencing.
-
Product
Travelling Wave Fault Location Test Kit
PH Series
-
PH series travelling waveform fault locating relay/equipment test set is a new device to meet the needs of testing and verification for travelling wave fault location equipment and protection relay with TWFL function.
-
Product
Connector, 104-Pin D-Type Female, Solder Bucket, 5A, 4-40 UNC Screwlocks
C104DFR-2SB-1A
D-Sub Female Connector
This 104-pin female D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied with rear cable entry backshell. This connector is suitable for use with Pickering modules that use the 104-pin D-type connector.
-
Product
Socket with Bifurcated Contact Solder Tail Pins
Series 0511
-
Strip-Line Sockets with Bifurcated Contact Solder Tail Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in solder tail or wire wrap pins. Consult Data Sheet No. 12009 for wire wrap pins. Optional spacer available for mounting on .300 [7.62], .600
-
Product
Millimeter Wave Continuously Variable Waveguide Attenuators
-
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
Product
200-480 degree Soldering Station
SM-936B
-
* Temperature range 200C-600C (392F-896F).* Ceramic heating element and sensor insures rapid heat-uptemperature.* Celsius or Farenheit temperature setting.* Temmperature adjusted by simply turning the dial.* Wide selection of tips available.
-
Product
Motion Reference Units And Wave Sensors
MRU And WS
-
The Motion Reference Unit (MRU) product line was first released in 2004 when Inertial Labs MEMS-based sensor solutions began to compete in performance with traditional FOG units. Easy integration of the MRU product line for the end user means competitive performance at no extra cost.
-
Product
Open-Frame Collet Socket with Solder Tail Pins
Series 518
-
Open Frame Collet Sockets with Solder Tail Pins. Features: Open frame allows for more efficient utilization of board space and better cooling. Choose from several pin styles. Compatible with automatic insertion equipment. Side-to-side and end-to-end stackable.
-
Product
01 With Soldering Eyelets | 12 Positions | M6
01-1xxx-00/30xx-12-M
-
Multi wafer compact selector with 30° detent angle, 3 mm shaft diameter, 25'000 switching cycles and with up to 6 Ncm switching torque
-
Product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5022
Amplifier
The HMMC-5022 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5022 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-22 GHz frequency range.
-
Product
Soldering Test
-
The soldering tests are conducted to determine if materials can withstand soldering effects, such as resistance to soldering heat, as well as the solderability of components during the manufacturing process.
-
Product
Arbitrary/Function Generator,2 Ch,150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing
T3AWG2152
Function Generator
Arbitrary/Function Generator,2 Ch,150 MHz,16 bit,128Mpts/Ch,6 Vpp output, Wave Sequencing.
-
Product
Solder Paste Printers
-
Shenzhen Leadsmt Technology Co.,Ltd
Is mainly used to print the solder paste to the circuit board, is one of the essential equipment in electronic manufacturing.
