RF Generators
Produce radio frequency (RF) signal for device evaluation and fault detection.
See Also: Generators, Waveform Generators, Frequency Generators
-
product
RF Helmholtz Coil
The Beehive Electronics 135A RF Helmholtz coil generates a well-controlled, uniform magnetic field. It can be used to calibrate magnetic field probes, such as the Beehive 100 series, or for testing the susceptibility of other devices to magnetic fields. The Helmholtz coil comes supplied with a fixture that makes it easy to calibrate Beehive 100 series probes.
-
product
PXI-5652, 6.6 GHz RF Analog Signal Generator
779670-02
6.6 GHz PXI RF Analog Signal Generator—The PXI‑5652 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5652 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
product
Signal Architect Simulator Software
GNSS
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
product
6.8 GHz Wideband Synthesizer with Integrated VCO
ADF4356
The ADF4356 allows implementation of fractional-N or integer-N phase-locked loop (PLL) frequency synthesizers when used with an external loop filter and an external reference frequency. A series of frequency dividers at another frequency output permits operation from 53.125 MHz to 6800 MHz. The ADF4356 has an integrated VCO with a fundamental output frequency ranging from 3400 MHz to 6800 MHz. In addition, the VCO frequency is connected to divide by 1, 2, 4, 8, 16, 32, or 64 circuits that allow the user to generate RF output frequencies as low as 53.125 MHz. For applications that require isolation, the RF output stage can be muted. The mute function is both pin- and software-controllable.
-
product
Analog Mixed Signal Testers
- PC-performance independent: multiple SPEA CPUs provide test program timing, while pc replacement does not require the test program requalification- Pattern-based programming: -30% test time vs competitors- 64-line synchrobus and 16-line high-speed synchrobus for real-time instrument synchronization: no embedded delay when running pattern-based testing- 99% parallel test efficiency- Multi-site test capabilities for up to 256 devices in parallel- High-density, floating instruments, for true parallel analog test- Universal slot architecture, up to 1,408 channels- RF generators up to 3 GHz
-
product
RF Signal Generators
The G6 VSG from Transcom Instruments is a Vector Signal Generator that operates from 10 MHz to 6 GHz. It can simulate GSM, EDGE, CDMA, TD-SCDMA, WCDMA, CDMA2000, TD-LTE, FDD-LTE, NB-IoT, and LoRa base station signals for production and calibration of UE, chips. The signal generator has a dynamic range (power range) from -100 to 10 dBm and an in-built automatic gain control function. It is available in a module that measures 180 x 50 x 290 mm and is ideal for educational practices, wireless monitoring, mobile communication, aerospace and national defense industry in terms of research, manufacturing, testing and measurement, and electronic countermeasure.
-
product
Digital Wideband Transceiver Analysis
S94610B
Digital Wideband Transceiver Analysis is an add-on software to Device Measurement eXpert (DMX) that adds cross-domain stimulus response measurements for digital/RF mixed-signal device characterization. Included Waveform Creator helps define digital IQ test stimulus waveforms that are used in the RF signal generators for receiver tests or downloaded to the digital-to-analog converters for transmitter tests. The DUT control is customizable to accommodate various data converters and transceiver types by defining device operation settings, transmit/receive switching, reading and writing digital IQ waveform from and to DUTs. Acquired RF or digital data is processed in the VNA’s applications for faster, accurate measurements and analysis.
-
product
Eddy Current Probes and Drivers
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
product
Reference Antennas
Type NRD
Reference antennas are precision dipole antennas that offer a fixed 2.15 dB of gain over an isotropic antenna along the major lobe axis at specified frequencies (2.15 dBi). They are intended to be used for antenna field pattern and gain measurements, or general RF sensing in the laboratory.
-
product
RF Signal Generator
RF Lambda’s RF signal generators are wideband DDS driven signal sources in a variety of frequency ranges. They offer extremely fine frequency step size and low phase noise as well as output level control. They are easy to configure with the included GUI and USB interface. They are AC powered for convenience.
-
product
PXIe-5745, 12-Bit, 6.4 GS/s, 2-Channel PXI FlexRIO Signal Generator
785598-02
The PXIe-5745 enables direct RF generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s for generation up to 1.5 GHz or in a single-channel wideband upconversion mode at 6.4 GS/s. The PXIe-5745 is ideal for applications that require high channel density IF signal generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for generating predefined waveforms, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA for dynamically creating waveforms, signal modulation/demodulation, and other custom real-time signal processing.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
784777-02
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
12GHz Dual Channel Signal Generator
LS1292B
The LS1292B is a 12GHz Dual Channel RF Analog Signal Generator, offers industry leading performance, in an easy to use benchtop box. It features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The design offers excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
PXIe-2540, 350 MHz, 8x9 PXI RF Matrix Switch Module
780587-40
PXIe, 350 MHz, 8x9 PXI RF Matrix Switch Module—The PXIe‑2540 is an RF signal switching matrix. With its non-blocking design, you can simultaneously connect any row or column within the switching matrix and maximize the flexibility of your test system. Isolation relays on the module disconnect unused parts of the switching matrix to maintain RF performance and high isolation. The density and bandwidth of the PXIe‑2540 is ideal for routing signals between digitizers, function generators, and other RF generators and analyzers.
-
product
PXIe-5654, 250 kHz to 20 GHz, PXI RF Analog Signal Generator
783127-01
PXIe, 250 kHz to 20 GHz, PXI RF Analog Signal Generator - The PXIe-5654 features a combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe-5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications. Some PXIe-5654 options include a PXIe-5696 Amplitude Extender Module. The PXIe-5696 supports a frequency range of 250 kHz to 20 GHz and an extended amplitude range up to 27 dBm.
-
product
RF Tracking Generators
Using a Spectrum Analyzer (SA) in combination with a Tracking Generator (TG) enables swept scalar frequency response measurements of active and passive networks.
-
product
6GHz Four Channel Signal Generator 19" 1U Rack Module
LS6084R
The LS6084R, 6GHz four channel RF Analog Signal Generator, offers industry leading performance, in a 1U, 19” space efficient, rack-mounted box. The LS6084R features four phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6084R was designed to offer excellent performance and abilities combined with an affordable price tag, needed from the R&D benches to the production lines.
-
product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
product
75Ω High Isolation LXI RF Multiplexer
Pickering's LXI high isolation RF multiplexers are suitable for switching 75Ω signals up to 1GHz - ideal for constructing complex microwave switching systems for many applications. These matrices are supported by a comprehensive range of cable and connector accessories and come with a standard 3 year warranty.
-
product
PXI-2796, 40 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module
782356-01
40 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module—The PXI‑2796 offers a high-density, unterminated multiplexer with dual 6x1 multiplexer banks in the same module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
product
RF Adapter Module For FlexRIO
RF Adapter Modules for FlexRIO feature frequency coverage from 200 MHz to 4.4 GHz, with up to 200 MHz instantaneous bandwidth. When paired with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, you can program the FPGA using LabVIEW to implement custom signal processing, including modulation and demodulation, channel emulation, spectral analysis, and even closed-loop control. These modules are all based on a direct conversion architecture and feature an onboard local-oscillator which can be shared with adjacent modules for synchronization. RF adapter modules also provide digital I/O capability for interfacing with external hardware.
-
product
75 Ohm Mini SMB Cable Assembly
40-977-751-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXI-2596, 26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module
778572-96
26.5 GHz, 50 Ω, Dual 6x1 (SP6T) PXI RF Multiplexer Switch Module—The PXI‑2596 is an RF signal multiplexer switch with dual 6x1 multiplexer banks in the same module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules. You can use the PXI‑2596 onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
75 Ohm Mini SMB to 1.0/2.3 Adaptor Assembly
40-978-731-0.1m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXI Quad SPDT RF Switch 6GHz 50 SMA Terminated
40-880-002
A range of 50Ω SPDT RF switching with automatic termination of unused signals. Available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules.
-
product
75 Ohm F-Type to F-Type Cable Assembly
40-977-781-0.5m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
PXIe-5654, 10 GHz or 20 GHz RF Signal Generator
783126-01
The PXIe‑5654 features an ideal combination of exceptional phase noise and frequency tuning time. These features address applications such as blocker test/receiver desensitization, high-performance intermodulation distortion measurements, and various electronic warfare applications. The PXIe‑5654 is designed to meet the challenging requirements of RFIC characterization, satellite test, and radar applications.
-
product
NI-5781 , 40 MHz Bandwidth, RF Adapter Module for FlexRIO
781267-01
The NI‑5781 is an analog dual-input, dual-output FlexRIO adapter module optimized for interfacing with baseband to RF upconverters and downconverters. When you pair the NI‑5781 with a PXI FPGA Module for FlexRIO, the resulting NI‑5781R is an FPGA-enabled reconfigurable I/O (RIO) baseband transceiver that you can use to implement custom RF modulation and demodulation, channel emulation, bit error rate testing, or spectral monitoring and jamming. Additionally, you can use the low latency and high throughput of FPGA‑based processing for ultra‑high‑speed control and inline processing applications.
-
product
75 Ohm SMZ/Type 43 Cable Assembly
40-977-711-2m
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
product
NI-5791, 200 MHz to 4.4 GHz RF Adapter Module For FlexRIO
782510-01
The NI‑5791 provides continuous frequency coverage from 200 MHz to 4.4 GHz. It features a single-stage, direct conversion architecture that provides high bandwidth in the small form factor of a FlexRIO adapter module. The onboard synthesizer, which is the local oscillator (LO), sets the center frequency for acquisition and generation, and you can export it to other modules for multiple input, multiple output (MIMO) synchronization. You can also import the LO from an external connector, enabling synchronization of up to eight NI‑5791 modules. For higher frequencies or a greater number of devices, you can use an external LO distribution amplifier.
