Solar Cell Substrate
thin crystalline material sliced from ingot.
-
Product
Solar Radiation Sensors & Transmitters
A70 Series
-
The Comptus A70 Series solar radiation sensors with transmitters are available in two models. The A70-A PAR Sensor measures photosynthetically active radiation (PAR) in the 400 to 700 nm range. The A70-I Insolation Sensor measures solar radiation in the 280 to 2800 nm range. The signals from the sensors are scaled by the signal conditioner to provide the desired output.
-
Product
5-in-1 Intelligent Cell Meter
#01444
-
Number of Cells: NiMH/NiCd: 4-7 cells; LiPo/Li-ion/LiFePO4: 1-7 cells
-
Product
Load Cell Amplifier Signal Conditioner with DB9 Connectors
MODEL LCA-9PC
-
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Pressure Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S Pressure Transducers manufactures a wide range of absolute and true gauge pressure transducers.*UNITECH’S Pressure Transducer is mainly a strain gauge based sensors ranging form Vacuum to 1200 Kg/cm2. *The stainless steel construction permits the transducers to operate in rugged, industrial environments. *We also undertake custom-built pressure transducer for specificrequirement and for OEM users.
-
Product
LC/MS/MS Method Package For Cell Culture Profiling Ver. 2
-
This Method Package enables the analysis of 125 compounds in under 20 minutes per sample. Performing analysis separately for each compound group such as amino acids and vitamins makes profiling of cell culture components very laborious, but with this method package a large number of culture medium components and secreted metabolites can be analyzed simultaneously.Compared to the previous version, several metabolites derived from amino acids, nucleic acids and the TCA cycle have been added, allowing even more comprehensive profiling information to be gathered.
-
Product
Load Cell Transmitter
MODEL SST-LV
-
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
High Precision Compression Type Load Cell
IR
-
A high-precision compression-type load cell is a sensor that accurately measures compressive (pushing) forces, designed for applications requiring very tight accuracy and reliability. It works by converting a downward force into an electrical signal, often using strain gauges to measure deformation, and is used in demanding fields like calibration, manufacturing, and medical equipment.
-
Product
Module Solar Simulators
QuickSun® 800-Series
-
800-Series simulators are always tested, certified and results reported exactly as specified in the applicable solar simulator standards and this is being proved by a globally recognized inspection body, SGS Fimko Ltd.
-
Product
Spectroelectrochemical Cell
SEC-C
-
Spectroelectrochemistry (SEC) is aimed at the investigation of electrochemical reaction mechanism and the interface structure between electrolyte solution and electrode. Remarkable progress in this field and related technology enables SEC to be applied in wide areas.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ6mm
CTF-6DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
Solar Simulator
-
Jiangsu Keyland Laser Technology Co., Ltd.
Features:- Beyond Class AAA performance- Stable continuous working- 8000 data collecting points- Durable flash lamp- Voice prompt- Measuring data export- Customizable for special panels
-
Product
Load Cells and Sensors
-
AMETEK Sensors, Test & Calibration
Our high quality load cells and sensors are used for materials testing and force measurement all over the world.The full bridge load cells and sensors provide high precision measurements that ensure adherence to the international standards.
-
Product
Load Cells, Weighing and Force Sensors
-
We are pleased to offer Load Cells from both Zemic and Vishay. We are the exclusive UK distributor for Zemic load cells.
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
Product
Fuel Cell Test Accessories
-
Scribner extends its groundbreaking line of tabletop fuel cell testing equipment with the 885 Fuel Cell Potentiostat.
-
-
Product
Scienlab Battery Test System – Cell Level
SL113XA | SL100XA Series
-
The cell is the basis of any battery system and directly influences its function, performance and safety. Therefore, it is essential to test and characterize the cell at an early development stage. For this purpose, Keysight offers reliable test systems for precise and reproducible measurement results. The Cell Level Series (SL1002A, SL1004A, SL1007A, SL1132A and SL1133A) — also known as Battery Cell Tester — emulates sink and source for battery cells for automotive and industrial applications.
-
Product
Steady-state Solar Simulator For PV Modules
SORAS LS
-
In certification laboratories for photovoltaic modules, steady-state solar simulators are mostly used for stabilization / light soaking tests (MQT 19) and hot-spot endurance tests (MQT 09) according to IEC 61215 and IEC 61730. An initial stabilization is required for all PV modules that undergo a standard test procedure. For the hot-spot endurance test (MQT 09), it is important that the operator has easy access to the front and back site of the module. During the test, it is necessary to shade one cell after each other to take infrared pictures, which requires good visibility of the entire back side. Our swiveling module holding system enables easy access to the front and back side of the module.
-
Product
Portable Hand Held Load Cell Indicator
MODEL SSI
-
The SSI is a Plug & Play Smart TEDS IEEE 1451.4 compliant portable handheld Load Cell Indicator. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SSI will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SSI can be set up by simple front panel push buttons. The SSI can be scaled to a full 5 digit display from 0 to 99,999 counts to read directly in engineering units such as grams, ounces, pounds, inch pounds, etc. The SSI also has a Units key for automatic conversion of readings for load, torque and pressure. The SSI has an ultra-fast signal-sampling rate of 15,360 samples/second for true peak and/or valley testing capability. Auto-tare allows the meter to be set to zero for any input signal level. The SSI also features a USB port for data logging to a PC. You can also log data to the SSI’s internal memory storing up to 16,000 time and date stamped readings. The SSI also features 2 built-in solid-state alarm relays with LED and audible indicators. The SSI will operate up to 65 hours on a single charge or use the included battery charger for applications where the SSI is mounted permanently.
-
Product
Flow Cell Kit
QCMT
-
The quartz crystal microbalance (QCM) technique under electrochemical frequency is very useful to determine many compounds such as metal proteins, metal ions and thiol-conjugated oligonucleotides.
-
Product
Cell Phone Detection
-
Berkeley Varitronics Systems, Inc.
Portable and fixed cell phone detection systems for securing corrections, law enforcement, government, TSCM, military, corporate and university facilities wishing to enforce a NO CELL PHONE POLICY.
-
Product
Multi Axis Load Cells
-
Multi-Axis Sensors are designed to measure a multiple of forces and moments simultaneously with a single load cell sensor. These sensors provide multiple bridges that precisely measure the applied force from one direction with little or no cross-talk from the force or moment.
-
Product
Stimulus Test Cell
HA7300
-
The Stimulus Test Cell HA7300 is a test cell which provides an environment for high-speed, highly accurate temperature and pressure test of differential pressure sensors, utilizing Advantest’s unique temperature control unit with simultaneous temperature control for 8 devices, as well as a newly developed 2Port pressure controller and pressure application nozzle.
-
Product
Solar Array Simulator
SAS
-
AMETEK Programmable Power, Inc.
A spacecraft solar array is subjected to large temperature excursions, varying insolation (the amount of sunlight falling on the array), mechanical changes and aging, which substantially effect both its short and long term performance. In order to test the spacecraft's power environment, a cost-effective solution for ground based testing is to utilize a solar array simulator.
-
Product
Solar Plants Controllers
-
Differential analog solar controller-Elios Basic for solar heating plants: it compares temperatures of fluids in the collectors and the storage tanks and, when the difference is greater than DeltaT, starts the heat exchange through the pump.
-
Product
Solar Simulator (JIS AAA)
PEC-L12
-
●A compact power supply box allows installation on a desktop●The irradiation direction can be freely rotated 360 degrees●A 5cm square optical filter can be attached●Quiet shutter sound (equipped with a low-noise shutter)
-
Product
Solar Power Meters
-
TES Electrical Electronic Corp.
Wide spectral range. Excellent long term stability.Cosine corrected. Automatic transmission measurements. Select either power or transmission. Solar energy measurement.
-
Product
Coating Thickness Meter for Ferrous and Non-Ferrous Substrates
CM8822
-
- Operating principle: magnetic induction/eddy current (F/NF)- Measuring range:0-1000um- Resolution; 0.1/1- Accuracy: 卤1-3%n or 卤2.5um- Min. measuring area: 6mm- Min. sample thickness: 0.3mm - Battery indicator: low battery indicator- Metric/ imperial: convertible- Power supply: 4x1.5V AA(UM-3)battery- Auto power off- Operating conditions:0-+45鈩?/span>(32鈩?/span>-104鈩?/span>),鈮?0%RH- Dimensions: 160x68x32mm- weight: 250g(not including battery)- Optional accessories: other range 0-200um to 15000um
-
Product
Light I-V Testing for Solar Cells
FCT-650
-
Advanced analysis of solar cells including light I-V and Suns-Voc data.
-
Product
Scanning Droplet Cell
VS-SDC
-
Scanning Droplet System (SDC) uses a compact peristaltic pump to force electrolyte through a small diameter tube and into a specifically designed head. This PTFE-based SDC head is machined to allow electrolyte to flow past an installed Reference Electrode and then to a port at the base of the head.
