CAN with Flexible Data-Rate
CAN compatible protocol with bit rates > 1 Mbit/s and 64 byte messages.
-
Product
CAN Data Logger
Rebel LT
-
The Rebel LT is an intermediate level CAN 2.0 data logging solution with the options to upgrade to GNSS with high meter level accuracy and 4G LTE. In addition these data loggers have 4 high speed analogue input channels and 3 digital I/O as standard.
-
Product
PCI-5922, 24-Bit, Flexible Resolution PCI Oscilloscope Device
779659-01
Oscilloscope
24-Bit, Flexible Resolution PCI Oscilloscope Device - The PCI‑5922 high resolution oscilloscope device features a flexible measurement resolution range up to 24 bits and up to 15 MS/s rates. This oscilloscope device has flexible settings for coupling, and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PCI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and any other small, accurate signal measurements.
-
Product
PXI-5922, 24-Bit, 32MB/ch Flexible Resolution PXI Oscilloscope
779153-02
Oscilloscope
The PXI‑5922 high-resolution oscilloscope features a flexible measurement resolution range up to 24 bits, with up to 114 dBc spurious‑free dynamic range (SFDR), and up to 15 MS/s rates. This PXI oscilloscope has flexible settings for coupling and voltage range, as well as a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. The PXI‑5922 is capable of taking extremely resolute and accurate analog measurements. It is ideal for audio signals, spectrum analysis, and other small, accurate signal measurements. The PXI‑5922 also features PXI synchronization and data streaming capabilities.
-
Product
Flexible LXI Microwave Switch Platform
-
These flexible LXI microwave switch platforms (model 60-890) may be specified with a mix of high-performance microwave relays up to 67 GHz bandwidth with 50Ω or 75Ω impedance and a range of connector types.
-
Product
Flexible Test System Automation Platform
RF2000A
-
The Ranatec RF2000A is a flexible test system automation platform that helps you to integrate your complete test system into a single box. No more cables and discrete parts on your desktop!
-
Product
Flexible x1 PCI Express to PCI Adapter
SKU-041-0X
-
The Flexible x1 PCI Express to PCI Bus Adapter (Adapter) was designed to convert the x1 PCI Express bus into two 32-bit PCI buses. It allows you to connect up to two 32-bit PCI expansion boards to the motherboard x1/x4/x8/x16 PCI Express connector.The adapter includes a PCI adapter, x1 PCI Express host board and a PCI Express flat cable.
-
Product
Switched Power Distribution Module, CAN Control
H730008FS
Switched Power Distribution Unit
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions:• Distributing the power to each device in a system• Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.The PDU has electrical monitoring of the load status in order to ease troubleshooting and maintenance tasks:• There are two light indicators per socket, to inform the user about:– Whether the plugged devices main switch is turned ON. This is helping to identify plugged devices with their main switch OFF, that therefore cannot be controlled by the PDU– Whether the power for the socket is ON. Therefore, (P ON) indicates that the PDU is giving power to the device.All the relays are CAN bus controlled.The unit has an extra power terminal block in order to extend to other units (connect more PDUs).
-
Product
Flexible Magnetic Field Probes
-
Projekt Elektronik Mess- und Regelungstechnik GmbH
The active probes are equipped with active amplifier electronics and have an extremely low-impedance output, ie they can also drive long lines. The output signal is calibrated according to specification. They can not only be connected to a certain type of teslameter, but can also be connected to any signal input.
-
Product
3U CompactPCI Serial Vector FlexRay CAN LIN Module Carrier
SFV-RAY
-
The SFV-RAY is a 3U CompactPCI Serial carrier card for the Vector VN7610 and similar Vector FlexRay/CAN-FD compact interfaces. On-board USB controller. Can be installed in any peripheral slot of a CPCI Serial backplane.
-
Product
CAN + OBD Network Data Converter
NC2
-
Add Vehicle Network based Data Acquisition to your existing fleet data acquisition systems for under one thousand dollars with the NC2. Great for NVH Tachometer applications.
-
Product
Analog And Digital Sensor Measurement Data For CAN Applications.
K- AN8
-
The stackable K-AN8 is our cost effective solution to measuring analog and digital/PWM sensors together in one module. Extremely easy to use and stackable with all of our other K-series instrumentation modules. The K-AN8 includes our unique power down and WakeOnCAN feature for quick installation on long term unattended fleet test vehicles.
-
Product
Flexible Printed Circuits (FPC)/Flat Flex Cables (FFC) Connectors
-
Panasonic Industrial Devices Sales Company of America
Connectors for flexible printed circuits (FPC) and flat flex cables (FFC). Height 0.9 to 1.8mm. Pitch between terminals 0.3/0.5mm. FPC / FFC is a one-piece type Connector that makes the connection with a directly-inserted FFC or FPC and locks it by means of a lever. This type of Connector can be used in a wide range of digital devices when a low profile or the horizontal insertion of flex is required.
-
Product
TRC-8542, CAN HS/FD Transceiver Cable
783699-02
Transceiver Cable
CAN HS/FD Transceiver Cable—The TRC-8542 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8542 to the port to support a CAN HS/FD. The TRC-8542 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
Product
Isolated Controller Area Network (CAN)
-
ADI isolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
Flexible PXI & PXIe Microwave Switch Platform
-
These flexible PXI & PXIe microwave switch modules (model 4x-890) may be specified with a mix of high-performance microwave relays up to 110 GHz bandwidth at 50Ω impedance or up to 2.5 GHz at 75Ω impedance and a range of connector types.
-
Product
Cable 2.92mm 40ghz VSWR 1.35 Max 24in 047 Flexible
C552-047-24B
Coax Patchcord
2.92mm Flexible Cable. 0.047" Diameter Cable so very flexible & easy to hook up. 24". VSWR 1.35 max.
-
Product
CAN Interface Board
-
- Auto Learning for slow detection and easy commissioning.- Encoder signal for floor detection.- Detail diagnostic of individual components ensures safety and reliable operation- Attached ARD for each panel for rescue in case of power fail.- Intelligent algorithm to attend any calls within 10 seconds for standard configuration.- VIP option, Fireman switch, overload protection $ protection of all other standard interfaces integrated.- Announciator is integrated with Gong bell.- Preferable selection of floor by user, software functional options, Delay times and important configurations.- Error diagnosis by PC interfaces, eleavator error history and services details make your maintenance job very effective and efficient in time period
-
Product
TRC-8543, CAN HS/FD or LS/FT Transceiver Cable
783701-03
Transceiver Cable
The TRC-8543 is designed to provide flexibility in connecting a CAN bus to the NI-9860, PXIe-8510, and/or the native NI-XNET port on a cDAQ-9134 or cDAQ-9135 controller. You can connect the TRC-8543 to the port to support a CAN HS/FD or LS/FT interface. The TRC-8543 is an isolated cable that includes the necessary transceiver for the bus type. It also features termination resistors that you can enable or disable in software.
-
Product
Switched Power Distribution Module, CAN Control
H730008BS
Switched Power Distribution Unit
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions:• Distributing the power to each device in a system• Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.The PDU has electrical monitoring of the load status in order to ease troubleshooting and maintenance tasks:• There are two light indicators per socket, to inform the user about:– Whether the plugged devices main switch is turned ON. This is helping to identify plugged devices with their main switch OFF, that therefore cannot be controlled by the PDU– Whether the power for the socket is ON. Therefore, (P ON) indicates that the PDU is giving power to the device.All the relays are CAN bus controlled.The unit has an extra power terminal block in order to extend to other units (connect more PDUs).
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131H
Calibration Cable
The Keysight 85131H is a 62.2 cm (24.5 in) long1 flexible cable with a 3.5 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.25 * sqrt (f) + 0.2 dB (where f is frequency is GHz) for the test port connector, and 1.5 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 3 inch radius. Stability1 of the Keysight 85131H is less than 0.12 dB and phase is 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
Easy I/O Flexibility Fanless Embedded Box PCs
ARK-2000 Series
Box PC
The Fanless PC ARK-2000 series is a brand new design with rich I/O, high flexibility and easy expansion capabilities. The rugged features of this Embedded Fanless PC include wide-input power ranges from 12V to 24V or 9~36V, wide temperature ranges from -20 ~ 70° C and structural strengthening. Multi-functional design technology simplifies your Embedded System applications.
-
Product
Flexible 32-bit PCI to x1 PCI Express Adapter
SKU-049-0X
-
The Flexible 32-bit PCI to x1 PCI Express Adapter (Adapter) was designed to expand the 32-bit PCI bus into an x1 PCI Express bus. It allows you to connect the x1 PCI Express expansion board to the motherboard PCI connectorThe Adapter includes an x1 PCI Express adapter board, 32-bit PCI host board and PCI Express Flat cable.
-
Product
Non-Isolated Controller Area Network (CAN)
-
ADI nonisolated controller area network (CAN) transceivers provide the differential physical layer interface between the data layer link, hardware protocol (for example, embedded in some of ADI's Blackfin® processors), and the physical wiring of the CAN bus. ADI's portfolio includes transceivers with integrated iCoupler® and isoPower® isolation, providing, fully isolated off-the-shelf CAN PHY's.
-
Product
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block
780041-01
Terminal Block
9-Pin Male D-Sub to 5-Pin Female Screw Terminal, Breakout for CAN Terminal Block - The CAN Breakout Box works with high-speed, low-speed, and single-wire controller area network (CAN) devices or PC interfaces. It features 14 ports for connecting devices with cables or directly to wiring harnesses. With an onboard power supply, the CAN Breakout Box can place power on the V+ pin required by some CAN transceivers. With a switch on the front panel, you can select 120 Ω, 60 Ω, or no termination on the network. You can use the CAN Breakout Box in desktop applications or mounted on a DIN Rail for test fixtures and cabinets.
-
Product
Flexible 32-bit PCI Riser
SKU-050-0X
-
The Flexible 32-bit PCI Riser (Riser) was designed to expand the 32-bit PCI bus into 2 32-bit PCI buses. The Riser includes a PCI adapter (downstream), 32-bit PCI host board and PCI Express Flat cable.The PCI adapter has 2 32-bit PCI slots for plugging in two 32-bit PCI add-in boards. The PCI host board connects to the motherboard PCI connector. The PCI Express Flat cable (12 inches) is used for connecting the host board with the PCI backplane, and it provides a flexible connection between the 32-bit PCI add-in boards and the motherboard.
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Flexible Functional Tester
igentic® 421t
-
Electronics customers require greater test flexibility to address the growing trend towards high-mix, low-volume printed circuit board (PCB) production. Sterner Automation is pleased to introduce the igentic® 421t, the next generation of automated test solution specially engineered to address these challenges. The igentic® 421t provides the flexibility, reliability and efficiency needed in one standard platform, allowing our customers to test multiple PCB's and significantly reduce individual product testing costs.
-
Product
Flexible MiniPCI Express to Two PCI Express Splitter
SKU-033-21
-
The Flexible MiniPCI Express to two PCI Express Splitter (Splitter) was designed to expand the modern motherboard (ATX, mini ATX, etc.) with a limited number of PCI Express connectors. It allows you to connect up to two x1 or x4 PCI Express add-in boards to the motherboard’s standard MiniPCI Express connector.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Arduino CAN Shield
IFB-10003-INP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
