Non-contact Temperature
products which sense, measure and/or detect temperature.
-
product
Extreme Temperature Active Probe, 1.5 GHz
N2797A
Testing devices over extreme temperature ranges is quite common these days. The N2797A single-ended active probe is the industry’s first low-cost high input impedance active probe with rugged probe tips for environmental chamber testing of ICs and devices. It gives the ability to probe signals at drastic temperature swings ranging from –40 °C to +85 °C. The probe provides 1.5 GHz of bandwidth and a 2 m long cable.
-
product
High Temperature Testing Mobile Conversion Unit
Used for applications that require high temperatures (1800C-2000C) for extended periods of time, the High Temperature Mobile Conversion Unit offers enhanced capabilities to accommodate more damanding requirements.The unit is based on the General Purpose MCU which allows for the use of standard specimen grips and accesories.
-
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Step & Repeat Non-Contact Inspection System for FPC and PCB
OHT-Ⅴ
*Space-saving design and highly efficient and high-speed inspection, with top and bottom slider structure*Roller head enables to handle the reverse imposition.*Easy operation by new alignment mechanism*The machine handlingPCB is called "WSR"
-
product
Precision Temperature Bridges - AccuBridge® Line
Measurements International Ltd.
Multiple Display Modes Including: Temperature (°C, K, °F), Resistance, Ω, Ratio, ADCC Technology, Accu-T-Cal™ Software (NMI Designed).
-
product
Temperature Measurement IR Sensors & Detectors
M34
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
product
Temperature logger (Medical)-40 to 85C
TK-4014-MED
The Tinytag Talk 2 Medical data logger is a simple, cost-effective way of monitoring the temperature of pharmaceuticals in fridges, freezers and cool (ambient) storag
-
product
Temperature Cycling Chambers
Global-N
ESPEC's Global-N is the faster temperature cycling chamber series. Two standard sizes of 380 and 800 liters (12 and 28 cubic feet) are available, designed to require the least amount of floorspace for this level of performance. Several models are available with temperature changes as fast as 20°C per minute
-
product
Temperature Stabilized Resistance Standards
Measurements International Ltd.
The temperature stabilized resistance standards offer customers the very best in accuracy, and stability. With 3 different models to choose from, covering the full range of resistance values.
-
product
Electronic Outside Air Temperature
OAT
The outside air temperature sensor is an electrical component that complements the control of a modern heating system.
-
product
Temperature and Humidity Chamber
GT-C52
Temperature and Humidity Chamber is for conditioning of samples prior to testing. It also can be used for a variety of material of high - low temperature alternating test. The test temperature, humidity, time can be programmed. Provides conditions of temperature from -40 degree to +150 degrees and of humidity 20% to 98%.
-
product
Temperature Transmitter
H4431
For external Pt1000 temperature probe. Three two-state inputs.
-
product
Non-contact Inline Sheet Resistance Measurement Module For Flat Panel Display
NC-600
*Non-stop and non-contact sheet resistance measuring of thin film on glass runs through on conveyer*1 to 10 number of probe by sizes of glass is attachable*Glass collision prevention function*Continuous test data report to the host computer
-
product
CO2 Concentration and Temperature Transmitter
T8448
CO2 concentration and temperature transmitter with serial RS485 output is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
product
Temperature Rise Test Panel
2000A
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
product
Temperature and Humidity Regulator
H3021-4
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Animal Temperature Control
TCAT-2AC
This version controls only AC powered heating or cooling devices such as a heat lamp. It is the least costly.
-
product
Humidity and Temperature
Humidity and Temperature Data Logger DL-200
Non destructive testing / Humidity and Temperature
-
product
Temperature Sensors
A device, typically, a thermocouple or RTD, that provides for temperature measurement through an electrical signal.
-
product
Portable for Temperature/ Humidity/ Pressure
Portable Data Logger for Temperature, Humidity and Pressure.
-
product
Temperature Controlled Air Bath
9300A
Measurements International Ltd.
The model 9300A series of Temperature Controlled Chambers is designed as a convenient and inexpensive way to maintain the temperature of air resistors in the calibration laboratory. It is large enough to house several standard air resistors and features two adjustable shelves to permit easy access to the standards. The shelves are easily removable.
-
product
Portable Temperature Monitor
PTM1
The Model PTM1 is a high performance, precision hand-held instrument for the measurement of temperature using Physitemp’s Type T (copper-constantan) thermocouples (will also accept J & K). This versatile instrument measures temperature in both °C and °F. The internal memory of the microcomputer stores the minimum and maximum measured temperature range for instant recall via the LCD display.
-
product
Non-Contact Mapping Life Time System
MWR-2S-3
The device is designed for express non-destructive contactless local measurement of non-equilibrium charge carrier effective lifetime in silicon substrates, epi-wafers and solar cells at different stages of manufacturing cycle. It can be used for incoming and outcoming inspection of silicon ingots and wafers, tuning and periodic inspection of semiconductor and solar cell technology quality. Lifetime determination is based on measuring photoconductivity decay after pulselight photo-exciting with usage of reflected microwave as a probe.
-
product
Outdoor Temperature Sensor
ENVIROMUX-STS-O
Applications from -40 to 185°F (-40 to 85°C). Accurate to within ±0.9°F (±0.5°C). Weatherproof enclosure. High resistance to external influences on the cable due to digital output signal. Re-calibration is not necessary after initial set-up. Quick release waterproof RJ45 connector. Supports CAT5/5e/6 cable up to 1,000 ft. (305 m). Powered by ENVIROMUX-2D/5D/16D. MTBF: 1,942,123 hrs. Compatible with ENVIROMUX-2D/5D/16D. Regulatory approvals: CE, RoHS.
-
product
Environmental Test Probe, Temperature
72-8364
Type K Surface Temperature Probe Surface probe is ideal for flat stationary surfaces such as molds, heating elements, integrated circuits, transistors and transformers. Very low sensor element mass enables fast response measurement time. Type K thermocouple temperature probes are commonly used with all types of industrial temperature controls and measurement equipment, and are compatible with Tenma handheld thermometers and digital multimeters that include temperature function. All are terminated with standard Type K plugs. See the complete line of Tenma Thermocouple Probes and Accessories
-
product
Temperature Data Logger
The temperature recording in a process is the most common and widely required application in any process. The commonly used temperature sensors are RTD Pt100 / Pt1000/ Cu53 / Thermistors and different kinds of Thermocouple. In order to avoid electromagnetic interference, the temperature signal is converted to 4-20mA and is carried to the logger. Our range of Temperature Data Logger includes Temperature Humidity Logger, RTD Data Logger, Thermocouple Data Logger and Flameproof Data Loggers.
-
-
-
product
Rapid Temperature Change Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is the company capable of offering a series of Rapid ESS Test Chamber,Rapid Temperature Change Test Chamber,Environmental stress screening (ESS) test chamber,Environmental stress screening test chamber,Temperature Change Test ChamberEnergy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions.
