Signal Sources
Instrument that provides a stimulus signal (waveform). (www.tek.com)
See Also: Signal, Signal Processing, Signal Integrity, Signal Proccessing, Signal Analyzers, Signaling, Signal Conditioning, Signal Generators, Signal Meters, Signal Conditioners
-
Product
RF Signal Amplifiers
-
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
Product
Rubidium Frequency Standard
RFS VXI
-
*RFS VXI is designed to work as part of information measuring systems based on the VXI bus as a rubidium frequency standard.*RFS VXI is intended for use as a highly stable laboratory signal source for checking generator devices, time-frequency measuring equipment and other equipment, synchronizing navigation systems.*The RFS VXI contains two independent rubidium reference oscillators: main and standby.*RFS VXI is a VXI standard, register based device and measures C-1.*RFS VXI implements the "Self-control" mode, which checks the output frequencies of the rubidium standard.
-
Product
LCM Tester
Model 27011
-
To meet the high accuracy and low price requirements for LCM Test device, Chroma 27011 that integrates the signal and power source provide a complete test solution for LCD Module. Its LVDS, TTL signal source fully complies with the digital signal standard, meanwhile with the 12V, 5V, 3.3V DC source output it is able to supply power to VDD, Backlight or LCM test without obtaining external power source.
-
Product
RF Signal Generator
-
RF Lambda’s RF signal generators are wideband DDS driven signal sources in a variety of frequency ranges. They offer extremely fine frequency step size and low phase noise as well as output level control. They are easy to configure with the included GUI and USB interface. They are AC powered for convenience.
-
Product
Microwave Downconverter, 3 GHz to 26.5 or 110 GHz
E5053A
Downconverter
The E5053A microwave downconverter is designed to operate with the E5052A/B signal source analyzer (SSA). When configured with the E5053A microwave downconverter, the E5052A/B SSA offers exceptional phase noise sensitivity up to 26.5 GHz. Additionally, combining a pair of 11970 series harmonic mixers offers the phase noise measurement up to 110 GHz.
-
Product
Measurement Hardware
-
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
Product
9kHz to 20/40GHz Signal Generator
CSG Series
-
Corech Microwave’s CSG series of Compact Microwave Signal Generators（Signal Source）operate from 9kHz to 20GHz / 40GHz. It offers high dynamic output power -120 to +17dBm, ultra low phase noise: -105dBc/Hz@10KHz, low harmonics and spurious. These exceptional performances make CSG9K20GA / CSG9K40GA an ideal choice for many test and measurement applications, including Semiconductor, Quantum Technology, Radar and Communication etc.
-
Product
Analog Output PXI Card
GX1642
Analog Output Module
The GX1642 is a 3U PXI digital to analog output board is designed specifically for applications where multiple analog outputs are required. The GX1642 offers precision signal sourcing performance and quality at an economical price.
-
Product
RF / MW switch
-
The RF / MW switch includes a variety of RF and microwave switch modules - RF multiplexers, which are available for use in the 34980A multifunction switch / measurement unit, providing broadband switching from DC to 20GHz . Use these modules to route test signals between your device under test and a signal source, oscilloscope, spectrum analyzer, or other instrument. The switch / attenuator driver module also controls the external switches and attenuators of the 34980A.
-
Product
RGB Color Bar Generator
CBG460R
-
The CBG460 is designed to provide an accurate and affordable signal source for system testing. It also provides the necessary components for aligning color monitors to the proper brightness, color and hue.
-
Product
GPS NTP Time Server - SYNTIME
-
Signals & Systems India Private Limited
Your product description goes hGPS NTP Time Server (SYNTIME) for Network Time Synchronization is a highly accurate time server. It generates time protocols to synchronize NTP/SNTP clients (Simple Network Time Protocol)/PTP clients (Precision time protocol IEEE 1588) over the network and operates at a speed of 10/100/1000Mbps. The NTP server accepts the time and frequency signals from sources like GPS or GLONASS. It achieves nanosecond accuracy and the system clock operates at stratum 1 when synchronized with time sources. It is a sleek, rack-mountable unit that synchronizes and maintains equipment/device time and avoiding any time drifts due to local RTCs. NTP output from time server supports unicast, broadcast, and multicast methods based on selection and behaves like a reference clock for the network. Apart from time synchronization protocols, it supports MD5 (Security key), SNMP, SSH, HTTP (Configuration), TELNET, FTP, and SYSLOG. IP address of the LAN ports can be field configurable.
-
Product
GPS/GLONASS Disciplined Rb Oscillator
VCH-311
-
GPS/GLONASS disciplined rubidium frequency standard model VCH-311 is a high stable frequency signal source (STANDARD mode), or precision frequency calibrator for any external standard signals (CALIBRATOR mode). The instrument contains multi-channel GPS/GLONASS receiver, time scale comparison unit and automatically adjustable Rubidium reference oscillator.
-
Product
Signal Amplifier
A10150
Amplifier
Model A10150 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, low distortion, signal amplification. With a high bandwidth of 150MHz, 20Vp-p into 50 ohms and a fast transition time of less than 1.8ns, the A10150 is the ideal complimentary amplifier to any high speed signal source that needs a supporting power boost for demanding applications.
-
Product
Signal Analyzer
-
Choose from an extensive selection of signal analyzer products from DC to 44.5 GHz and extendable to 325 GHz.With excellent total level accuracy, dynamic range and performance, Anritsu spectrum/signal analyzers not only can capture wideband signals but FFT technology supports multifunction signal analyses in both the time and frequency domains. Moreover, the built-in signal generators on some models outputs both continuous wave (CW) and modulated signals for use as a reference signal source.
-
Product
FOCL Reference Signal Modem
VCH-607
-
FOCL reference signal modem VCH-607 is designed to receive and transmit electrical signals with a nominal frequency of 100 MHz through a fiber-optic system and generate electrical signals with a nominal frequency of 5 and 10 MHz, coherent with the input signal. Reception and transmission through the FOCL is provided using a pair of modems: one is configured as a Transmitter and is installed at the end of the FOCL where the signal source is located, the second is configured as a Receiver and is installed at the opposite end of the FOCL.
-
Product
Analog Output / Arbitrary Waveform Generator
GX1632e
Waveform Generator
The GX1632e is a 3U PXI Express digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1632e offers 32 output channels with 16-bits of precision signal sourcing performance. Three modes of operation are available including Analog Output, Arbitrary Waveform Generation (ARB) and Data Streaming.
-
Product
Plug-On Transmitter
HMa
-
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
Product
LINEAR AMPLIFIERS
-
These amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance and fast response. The output is linear from DC up to megahertz range.
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Product
Signal Analysis
Synchronous Accumulation (Order Analysis)
-
Order analysis is one of the most convenient and efficient methods for diagnostics and balancing of rotating mechanisms and transmission gears. With an RPM sensor and a vibration sensor, it is possible to study the time characteristics of gear vibration signals. It is a well-known fact that a signal from a vibration sensor is affected by signals from other sources. To tune out from the disturbing signals, the synchronous signal accumulation method is used. For each shaft rotation, the RPM sensor provides a rotation mark. This signal serves as a triggering strobe for the vibration sensor signal sweeping. The obtained signal sweeps are combined. All the sources of the signals related to the shaft frequency (frequency of rotation) are accumulated and increased in the accumulator linearly proportionally to the N number of rotations. All other signals that are not correlated with the shaft frequency are accumulated proportionally to N1/2 and in case of a greater number of averagings, the useful signal exceeds the interference level.
-
Product
Phase Noise Generator / Calibrator
PNG-A
-
Noise eXtended Technologies S.A.S.
The PNG-A is a high precision generator used in Test and Measurement instruments calibration. It is a Signal Generator with precisely computed phase and amplitude noise characteristics. With its wide frequency offset range, 1Hz to 1 MHz offset, and its programmable Phase and Amplitude noise in real time, this is the ideal standard to calibrate phase noise analyzers, Signal Source Analyzers and Spectrum Analyzers.
-
Product
NI-9231, 8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module
783610-01
Sound and Vibration
8-Channel, 51.2 kS/s/channel, -5 V to 5 V, C Series Sound and Vibration Input Module - The NI-9231 is a high-density sound and vibration module that can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. It can perform the high dynamic range measurements necessary for modern measurement microphones and accelerometers and features simultaneous sampling. The NI-9231 incorporates both a TEDS input path and 2 mA of IEPE signal excitation source that can be turned on and off, removing the need for external sensor power and reducing the complexity of the data acquisition system.
-
Product
RF Noise Source
NS-3
-
The NS-3 Broadband RF Noise Generator provides an extremely flat AWGN (Additive White Gaussian Noise) signal from 5 to 2150 MHz. The output level adjusts in 0.1 dB steps over a 30 dB range.The bench-top configuration is standard and an optional two unit rack enclosure is available. The RS232 or USB remote control interface simplifies its use in automated test and factory ATE environments. The NS-3's combination of range, versatility and value make it the ideal general purpose broad-spectrum signal source for bench and ATE applications, including C/N, BER, MER, PER testing and rain fade simulation.
-
Product
PXIe Vector Network Analyzer RF Distributor
M9340A
Vector Network Analyzer
The M9340A PXIe vector network analyzer RF distributor is used in the M9485A PXIe multiport vector network analyzer. The module distributes the source and local signals from the source modules to the receivers.
-
Product
Electrical Calibration
GF6018A
-
Beijing GFUVE Electronics Co.,Ltd.
The equipment is compliance with national verification regulation: JJG1242005 "Ammeter, voltmeter, power meter and resistance meter verification rules" and related national standards. 0.05 single-phase AC/DC standard source, can verify magnitude 0.2 and the following AC/DC voltmeter, ammeter, frequency meter, resistance meter. The source signals by using DSP and 16-bit high-speed analog-to-digital converters of controllable sine wave, the distorted wave signal source.The equipment comes with RS-232 interface, can be connected with PC to a semi-automatic verification system. It has precise interface and multi-functions including verification, storage and query.The equipment adopts color LCD screen, chart character display is clear, with high precision, stable and reliable, convenient operation and flexible characteristics.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
2 Channels, 28-115 Vrms, 47 Hz-2.5 kHz (max. range) programmable
AC3
-
The module is used to provide an AC signal source when a secondary reference source other than the optional on-board reference module is required. The modules are programmable for full range voltage outputs from 2 to 115 VAC, and frequency from 47 Hz to 10 kHz.
-
Product
6GHz Dual Frequency Synthesizer moduleValon
5009
-
The Valon 5009 Dual Frequency Synthesizer module is our latest offering in high frequency synthesizer sources. These frequency synthesizers are perfect in applications that require a spectrally pure and highly stable signal source or timing clock. Our synthesizers have replaced laboratory generators costing many times more in a number of applications. Each module actually contains two independent sources locked to the same internal or external frequency reference or standard. Having two phase coherent sources in the same convenient package opens up a wide variety of test applications and solutions
-
Product
Calibrators
-
Orbit Controls calibrators are suitable as signal sources for test benches or laboratories. They can be used as generators for calibrating and testing electronic measuring devices or assemblies, both by manufacturers and by companies that must perform periodic calibration tasks for quality certification.
-
Product
SSA-X Signal Source Analyzer, 1 MHz To 8 GHz
E5055A
Signal Analyzer
The Keysight E5055A SSA-X signal source analyzer provides precise and accurate measurements in one box. Comprehensive and versatile, this solution evaluates the phase noise and other relevant parameters for RF signals up to 8 GHz. Flexible measurement settings and a modern user interface improve measurement efficiency, while application support through software expands measurement coverage to meet new requirements.
