-
Product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
-
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
Product
Pneumatic Contact, ITA, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610132104
Pneumatic Contact (ITA)
Primary mating contact 610131104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Pressure Fittings
-
AMETEK Sensors, Test & Calibration
Our CPF Fittings & Hose are a new line of quick-test pressure fittings for calibration & test applications - designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 10 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidently disconnect from a pressurized system. It can also be used as a bleed point. CPF fittings seals two ways: use fingers for an o-ring seal or use a wrench for a metal to metal cone seal (good to -40°C).
-
Product
Save A Drop Water Meter
P0550
-
Is your water bill out of control? Part of the problem could be that you’re over-watering your garden! Now you can take control of both with the unique Save A Drop® Water Meter. Simply attach between the faucet and hose and the easy to read meter shows you how much water you’re using. It accurately measures both single waterings use as well as cumulative water usage to accurately meet your garden’s (and wallet’s) needs.
-
Product
Temperature Forcing System
ETF-SERIES
-
Precise Temperature Accuracies with Reliable Test Results Temperature Limits: -40/-60 °C to 30 °C Temperature Accuracies: ±2-3°C Temperature Rate of Change: 20-25 deg /min (Non-linear) Maintenance Free Access to The System Self-Sufficient System Compact with small footprints suitable for any space constraint laboratories Low decibel system Suitable for testing electronic chips / devices Environmentally friendly refrigerants Efficient heating Microprocessor based single set point PID temperature controller with data logging Flexible hose up to 2.5-3.0m Interchangeable heads according to chip size. Inbuilt electrical control panel with switchgear system
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-72x24x12
-
The 6 ft wide by 2 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Fuel Pressure Testers
-
• Developed with input from technicians on adaptor selection for 7.3 L, 6.7 L, 6.4 L and 6.0 L Ford®Power Stroke®engines• 0 100 PSI gauge and hose assembly• Low-pressure diesel-fuel delivery testing (lift pump)• Correct fuel delivery and dynamic fuel pressure are crucial to having a properly running engine• Helps prevent a lean condition that may cause burning of injectors or scorched cylinders• Convenient protective slide-lid case that will fit in a 4" drawer for easy tool access• Technical Support: 1-866-713-6007
-
Product
Hydraulic Hose Assemblies, 15,000 psi, US Army
9801B Tester
-
The 9801B hydraulic hose tester is utilized by the U.S. Army for high pressure testing of hydraulic hose and tube assemblies as well as any component testing requiring test pressures up to 15,000 psi. Enhanced safety for operating personnel is achieved by utilizing the optional 8801HT integral test chamber which was designed specifically to fit to all our 8801B and 9801B testers.
-
Product
Radiator Flow Test Machine
8601
-
The Radiator Flow Test Machine P/N 8601 meets all requirements of military specification MIL-F-45955A (AL). It is completely self contained and requires only connection to a source of shop electrical power to place in operation. A power cable complete with three prong grounding plug is permanently attached to the machine for this purpose. The unit consists of a water storage tank, a pumping system, a flow measuring system, a support and workstation, and the required hose adapters for connection to different size radiators. The complete unit is mounted on swiveling casters. The flow rate is infinitely adjustable from 0 to 120 gallons per minute by means of a panel mounted control valve. The machine is constructed from heavy 10 gauge steel, is double welded and is coated externally and internally with a water-resistant epoxy coating. Flow measurement is accomplished by a digital panel meter with a calibrated accuracy of plus or minus 3 percent of scale between 5 and 120 gallons per minute. Higher flows available on request.
-
Product
Liquid Nitrogen Generator
-
The Liquid Nitrogen Generator is your reliable and efficient on-site plug and produce cryogenic solution. With a small footprint, low power consumption and no need for cooling water or water chiller makes the TRITON2+ and Triton-2 the best solutions available on the market. With integrated cooling fans can operate with air cooling up to +32°c ambient temperatures making it suitable to operate in most parts of the World. Simply connect the power and press start for the machine to automatically produce liquid nitrogen when needed. The safe front flask dispenser makes dispensing LN2 safer than ever with other options such a s a rear hose connection available to connect to freezers.This makes possible to cryopreserve important biological samples in a stable and reliable manner.Nitrogen is used primarily:food industry, Medical treatments, and Also Liquid nitrogen used for medical cooling systems for the preservation of cord blood tissue and eggs
-
Product
Pitot Static Tester
ADSE 746
-
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
Product
Fuel Cells
-
continuously variable contact pressure ensures complete reproducibility of the test conditions ● independent of the thickness of the fuel cell components due to the self-adjusting piston and special sealing concept ● no connection and disconnection of hose- or cable connections for the exchange of cellFixture necessary ● fast &Easy clamping of the cellFixture without tools and precise exchange of the internal cell components ● maximum power density by determining the optimal contact pressure on the active cell surface ● developed for high stress in the field of quality assurance and laboratory environment
-
Product
Needle Pressure Gauge
102
-
The Elcometer 102 Needle Pressure Gauge is designed to measure air pressure up to 20bar (300psi) in blast and air hoses. Pressure drop is responsible for decreased production rates, increased abrasive consumption and reduced anchor profile in abrasive blasting systems.
-
Product
Safety Chamber, Hydrostatic Test
9901HTX-36x36x15
-
The 3 ft wide by 3 ft deep Hydrostatic Test Safety Chamber, when combined with one of our pump systems, provides a complete hydrostatic test system for testing hose and assemblies or other components requiring pressure testing.
-
Product
Pneumatic Contact, ITA, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610132101
Pneumatic Contact (ITA)
Primary mating contact 610131101.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferruless fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Pneumatic Contact, Receiver, Hose Barb, for 1/8" [3.2 mm] ID Tubing
610132105
Pneumatic Contact (Receiver)
Primary mating contact 610131106.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included). The 1/8" ID connectors are available with hose barb.
-
Product
Pneumatic, Contact, Receiver, Ferruless Fitting, for 3/8" OD, 1/4" [9.5 x 6 mm] ID Tubing
610131101
Pneumatic Contact (Receiver)
Primary mating contact 610132101.Pneumatic Contacts are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
Product
Petrol Engine Compression Tester 0-300Psi/0-21Bar
DCT1
-
Suitable for use on most petrol-engined vehicles including motorcycles. Comprises 300mm flexible hose, with 14mm and 18mm threaded adaptors, large easy-to-read scale (0-300psi/0-21bar) and air release valve to allow rapid retesting.
-
Product
Hydrostatic Testers
-
Hydraulic Technology Inc. has been manufacturing hydrostatic test equipment to the U.S. Military, aerospace and industrial sectors for over 30 years. These hydrostatic test systems are used for both high pressure proof testing and burst hydrostatic testing. By simply connecting one of our hydrostatic test systems to a shop air supply, safe high pressure testing can be accomplished with hydrostatic test output pressures available up to 15,000 psi. Among other specifications, our hydrostatic testers meet the requirements of MIL-T-25456, A-A-52687 AND PD02LEEE07. In addition to U.S. Military stock listed hydrostatic testers, we manufacture both standard and custom hose proof test stands, portable hydrostatic testers, hydrostatic test chambers and ancillary equipment to fit individual customers’ needs as required. We can typically ship standard units within 24-72 hours, sooner if required.
-
Product
Automatic Transmission & Engine Oil Pressure Tester with 2 Gages
34580
-
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Includes two gages: Large Gage calibrated from 1-600 PSI (0-4,000 kPa & 0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR) Large gage can be used for all applications and has hang-up hook. Small gage is for more accurate reading of engine oil pressure where maximum oil pressure does not exceed 50 PSI (3.5 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a molded plastic case.
-
Product
Hydrostatic Test Pump, 6300 psi, P/N 9501C - USAF
9501C
-
The 9501-9501C hydrostatic test pump provides a safe source of hydraulic pressure for proof testing pressure vessels, hose and tube assemblies or other components that require periodic proof pressure testing.
-
Product
8-Pin Pneumatic Block
-
8-pin pneumatic block | Adapter side Equipped with KDV-PK-3 (460043) Grid dimensions: 10-11mm and 12-13mm 4mm hose Plastic: With pin contact HAN module (278255)
-
Product
8-Pin Pneumatic Block | Receiver Side
-
8-pin pneumatic block | receiver side, Equipped with KSV-PK-3 (462011), Grid dimensions 10-11mm / 12-13mm, 4mm hose, Plastic: With socket contact with shut-off HAN compressed air socket (278256)
-
Product
Hybrid / Optical Dry Mate Connector
-
The Teledyne ODI Dry-Mate Submersible connector series is designed to directly complement the wet-mate hybrid connector series (Rolling Seal), and also for use as a stand-alone connection system. Two standard shell sizes are available, depending on the circuit configuration. In addition, straight, 45°, or 90° termination versions can be provided. Used in conjunction with Teledyne ODI's oil-filled hose, this system is designed for submersible applications up to 9,100 psi. A unique tri-lobe keying system assures proper alignment.
-
Product
Tank & Vessel Cameras
-
Advanced Inspection Technologies Inc.
For remote viewing large areas, tanks, pressure vessels and pipes where limited access, radiation or safety makes inspection difficult. Each inspection camera system features a color camera module, high-intensity lighting, pan-and-tilt mechanism and industrial waterproof hosing for protection from extreme environments.
-
Product
Automatic Transmission & Engine Oil Pressure Tester
34500
-
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Gage calibrated from 0-600 PSI (0-4,000 kPa & 0-7.0 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a durable vinyl pouch.
-
Product
Diesel Compression Tester
34700
-
Measures cylinder pressure on diesels equipped cars and trucks. Records maximum pressure reached during engine test. Release valve allows for immediate venting and resets gage for repeat tests. Swivel end quick coupler is connected to adapters sold separately. High pressure hose is 16 1/2" long. Gage is scaled from 0-1,000 PSI and 0-70 BAR.
-
Product
Pneumatic, Contact, Receiver, Hose Barb, for 3/8" [9.5 mm] ID Tubing
610131104
Pneumatic Contact (Receiver)
Primary mating contact 610132104.Pneumatic Connectors are available with either ferruless polytube fittings (3/8" tubing OD) or hose barb (3/8" tubing ID). Ferrules fittings securely attach tubing without hose clamp - which is recommended for the hose barb type (hose clamp not included).
-
Product
Fuel Pressure Tester Kit
FIT500
-
Performs running, residual, rail and flow rate pressure tests.Professional dual scale gauge reads 0-100psi and 0-700 kPa with relief valve and fuel discharge hose and protective rubber boot.
-
Product
Ralston Quick-test™ Microbore Calibration Hoses
-
Ralston Instruments Quick-test™ hoses can be attached and detached without a wrench or thread sealant while maintaining a working pressure of 6900 psi (475 bar). Quick-test hoses are small in diameter, flexible, and low in volume. These hoses provide an ideal way of transmitting pressure during a vacuum or pressure calibration. A wide variety of adaptors provide a connection for most calibration applications.
