Power Amplifiers
-
Product
Driver Amplifiers
-
Analog Devices RF amplifiers are designed utilizing the company’s leading amplifier and RF IC expertise. Our extensive family of single-ended input/output, fixed-gain amplifiers can be used from dc to microwave and include gain blocks, low noise amplifiers, intermediate frequency amplifiers, driver amplifiers, and differential amplifiers. These devices offer high linearity, low noise figures, and various fixed-gain options, as well as low power consumption; they are all fully specified over frequency, temperature, and supply voltage for use in a variety of applications.
-
Product
Power Sequencing
-
Renesas' power sequencing controllers are integrated 4-channel controlled-on/controlled-off power supply sequencers with supply monitoring, fault protection and a “sequence completed” signal.
-
Product
Power Supply
VITA, VPX, VME, cPCI
-
PCI-Systems Inc. intelligent power supplies integrate a microcontroller (MCU) for a fully programmable and flexible solution. Intelligent power conversion allows configuration and reconfiguration for different applications. With intelligent power conversion, the power supply becomes a platform solution for many different applications. The power supply can easily be reprogrammed to support different operating limits and control inputs.
-
Product
Switched Power Distributed Module, CAN Control
H730008xS
Power Module
The intelligent Power Distribution Unit (PDU) H7300.08xx has two main functions: Distributing the power to each device in a system Switching on the devices sequentially, in order to minimize the inrush current from the switched power supplies, that might affect the contactors.
-
Product
Slim & High-Performance Charge Amplifier
6001-A, 6002-A
-
Measuring a wide variety of vibration: automotive, rail transportation equipment vibration, motor/pump vibration, vibration response during vibration test. Also available for a vibration test device for calibration of equipment.
-
Product
System Amplifier
SAM100
-
The R&S®SAM100 system amplifier is an ultra-broadband solid state microwave amplifier with a frequency range from 2 GHz to 20 GHz. With a power of up to 20 W, outstanding linearity and very good noise characteristics, the R&S®SAM100 amplifier is ideal as a compact system amplifier in various measurement setups e.g. design (DVT) and product validation test (PVT) or EMC. In measurement environments with R&S generators, frequency analyzers or network analyzers, they can act as drivers or boosters and amplify the measurement signals
-
Product
Distribution Amplifiers
-
Step up to a leading range of distribution solutions. Take a single input signal and feed it to multiple locations while still maintaining guaranteed signal quality. Choose from our range of solutions for every need and every budget.
-
Product
Amplifiers
-
low noise wideband current amplifiers (current to voltage converter) with a high gain and wide frequency band.CA261F2 and CA-461F2 are low noise voltage amplifiers which realize high precision signal processing and high density mounting by using single-in-line package which has six-surface strict shield.
-
Product
Low-Noise Amplifiers
-
Broadband, narrowband, high-frequency, our extensive portfolio of LNAs is ready to tackle the toughest requirements. Don’t see exactly what you need? We have a vast library of pre-engineered building blocks ready to support any custom design.
-
Product
400 W 6U CompactPCI Hot-Swappable Redundant Power Supply
cPS-H640/48
Redundant Power Supply
- PICMG® 2.11 CompactPCI® Power Interface compliant- 6U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 400 W DC output, maximum 480 W peak output
-
Product
Power Supplies
RM - SERIES
-
With dual PCI-E connectors, the RM Series carries all its essentials to power your system. Enjoy the graphic rendered programs and games without the threat of overheating. Its dark aluminum chassis not only looks good, but dramatically relieves heat built-up. The 120mm cooling fan enhances the already efficient heat dissipation rate and helps balance the cooling system with noise level. The RM Series is great for high end users to everyday casual users. Whatever your system needs, the RM Series can deliver.
-
Product
Inline Optical Power Meter - PXI
Power 1600 Series
Power Meter
Quantifi Photonics’ Power 1600 Series inline optical power meters provides quick and accurate inline power monitoring. Seamlessly integrate the power meter into your new or existing PXI test setup and save space, lower your costs and improve testing efficiency.
-
Product
Power Limiters
-
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Product
PXI Amplifier And Attenuator Modules
-
Pickering's PXI Amplifier and Attenuator Modules include our accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices. The other programmable attenuator available has a bandwidth between 10MHz and 6GHz available in triple or hex formats.
-
Product
Power Supplies
ZPG - SERIES
-
80Plus Gold Certified provides typical 87% efficiency at 50% of max load. The ZPG series can give you the power you need at higher efficiency, which means you can use the same power with less energy. Built in QUAD 8-pin PCI-Express graphic card connector offering further upgradability.
-
Product
Bench-Top Type Amplifiers
-
– A variety of wavelength bands– Most models have the RS232C / IEEE488.2(GP-IB) interface as default– customization is available– Development of next-generation optical communication systems– Amplification for evaluation of transmitted signals– Detection of faint signals in optical measurements & sensors
-
Product
Power Sources
MS-Series
-
The MS-Series Power Sources are high performance, high efficiency, AC to AC converters. Rugged powerful output provides up to 350 amps of pulse current for driving non-linear loads.
-
Product
Distributed Amplifiers
-
Macom Technology Solutions Holdings Inc.
At MACOM we design, manufacture, and support distributed amplifiers that provide a simple and easy solution for a wide variety of commercial and aerospace & defense applications. MACOM’s distributed amplifier family cover frequencies from DC to 80 GHz and are offered in both bare die and air cavity packages. These devices offer an excellent combination of broadband performance and ease of use for a variety of high-performance applications.
-
Product
Autoranging System DC Power Supply, 750 V, 20 A, 5000 W, 400 VAC
N8944A
DC Power Supply
The Keysight N8900 Series is a family of 5 kW, 10 kW, and 15 kW autoranging, single-output power supplies available in 14 different voltage, current, and power combinations and either 208 VAC or 400 VAC (28 total models).
-
Product
Instrumentation Amplifiers
HIGH-POWER RADIO FREQUENCY (RF) AND MICROWAVE AMPLIFIERS, TWTA AND SOLID STATE
-
Communications & Power Industries
electromagnetic compatibility (EMC) high-intensity radiated field (HIRF) testing, military testing, electronic warfare simulation and scientific applications are based on the same switched-mode power supply technology as its rugged amplifiers. As a result, these instrumentation amplifiers have all the same performance and reliability advantages as the rugged product line, but have been neatly re-packaged into compact, lightweight and affordable rack-mountable units more suitable for less demanding physical environments. CPI TMD's new modular design (the PTCM range) has many user benefits, including advanced self-diagnostics, ethernet interfaces, remote management, VSWR protection and plug and play field replaceable power supplies.
-
Product
Power Dividers
-
Powers plitters can divide one signal into two or N way equal or non-equal energy, in reverse,they are also used as combiners by combining multiple signal into one. They are mainly used in feed network in antenna array, mixer and balanced amplifier, finish the work of distributing, combining and measuring power, isolating signal sources and measuring swept reflected coefficient etc.
-
Product
Low Noise Amplifier
-
The COMM-connect Low Noise Amplifier can be used to amplify signals in a wide range of bands. The amplifier comes equipped with a SMA connectors, for easy installation. Mechanical mounting is made easy by mounting flaps protruding the casing.
-
Product
Standard GaN Amplifiers
-
A GaN (Gallium Nitride) amplifier is a power amplifier that uses GaN, a wide-bandgap semiconductor material, to provide high power density, efficiency, and frequency capabilities.
-
Product
Micro Power, Contact, ITA, 21 Amp, 12-14 AWG
610143101
Power Contact (ITA)
Primary mating contact 610142101. (May mate with other Receiver contacts, as well.)Specifications Operating Current 21 amps continuousContact Resistance 1.5 mOhms max.Dielectric Withstanding Voltage (DWV) 1500 VDC min.Contact Body BrassContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 10,000 cyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs) 1.23u
-
Product
RF & Microwave Broadband Amplifiers
-
SHF Communication Technologies AG
SHF has been active in the design and production of broadband RF-microwave amplifier. The outstanding performance makes our amplifiers suitable for a wide variety of applications in R&D. This includes not only optical communications, but also satellite communications, high-speed pulse experiments, data transmission, quantum communication, radar and antenna measurements.
-
Product
TV Amplifiers
-
PLANAR broadband amplifiers are designed to amplify television signals in the range up to 862 MHz in the forward direction, as well as to transmit internal system signals in the reverse direction in cable distribution networks.





























