-
Product
Industrial Raspberry Pi 4 HAT Gateway Kit
UNO-220
-
Industrial-grade gateway kit provides Raspberry Pi-ready solutions for rapid prototypingProtect your Raspberry Pi device from dust and temperature extremesDesigned for Raspberry Pi single-board computers - develop unique IoT applicationsUNO-220 industrial-grade chassis transforms RPi 4 into a ruggedized gateway for shopfloor environmentsIndustrial grade I/O board for RS-232/485 and GPIO extensionBuild IoT applications with the UNO-220 Industrial Kit for Raspberry Pi 4Provide optimum protection and 2-years warrantyAmazon AWS IoT Greengrass certified
-
Product
SparkFun MicroMod RP2040 Processor
-
The SparkFun MicroMod Pi RP2040 Processor Board is a low-cost, high-performance board with flexible digital interfaces featuring the Raspberry Pi Foundation's RP2040 microcontroller. With the MicroMod M.2 connector, connecting your MicroMod Pi RP2040 Processor Board is a breeze. Simply match up the key on your processor's beveled edge connector to the key on the M.2 connector and secure it with a screw (included with all Carrier Boards).
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
USB Line Scan Camera
Inexpensive
-
Compact USB line scan camera with high sensitivity and resolutions from 2048 to 4096 pixels. The programming interfaces, including drivers, libraries and programming examples, enable the USB line camera to be integrated into your own application. The line scan camera is supported under the following operating systems:*Windows*Linux*Linux ARM 32Bit (Raspberry PI)*Linux ARM 64Bit (NanoPi M4 & NVIDIA Jetson Nano)
-
Product
Hardware Debugger for the Raspberry Pi
TAP-HAT
-
The TAP-HAT is a low-cost hardware debugger for the Raspberry Pi®. Its flexible multi-modal design supports USB-connected hardware debugging of a Pi board, connection of external hardware debuggers to a Pi, or use of the Pi as a network attached hardware debugger.
-
Product
Dual MAX31865 PT-100 RTD to Digital Breakout
SEN-30202-PT100
-
Dual channel breakout board for the MAX31865 RTD-to-Digital converter from Maxim. Two breakout hardware configurations are available standard, designed to interface with either the PT100 or PT1000 platinum RTDs. For non-standard applications, including thermistors, custom hardware configurations can be accommodated. Contact Technical Support for more information. RTD devices may be wired in 2, 3 or 4-wire configurations using the 4-pin screw terminal input. The MAX31865 breakout is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance.
-
Product
USB Line Scan Camera
TinyUSB
-
*Very small and compact dimensions, only 40 x 30 mm²*High speed, up to 9kHz line rate*Programmable amplifier and offset*Supported operating systems:****Windows**Linux**Linux ARM32 (Raspberry PI)
-
Product
Breakout Boards
-
Breakout your Raspberry Pis and Arduinos with this broad selection of versatile breakout boards! Engineered to help you realize your robotics, GPS and altitude sensing projects as well as servo and touch screen interfacing, you''ll find many uses for these high-quality boards, most of which are manufactured in house at Adafruit!
-
Product
Visual Designer For Arduino™
AVR And Raspberry Pi®
-
Proteus Visual Designer combines world class Proteus VSM simulation with an easy to use flowchart editor and a gallery of virtual hardware to provide a truly integrated and intuitive development environment for Arduino and Raspberry Pi. The peripheral gallery makes hardware design easy. Simply add a shield or sensor from the gallery and Visual Designer will automatically place the correct circuitry on the Proteus schematic for you and add some simple methods to Visual Designer that allow you to control the hardware. The software is then designed as a flowchart so you can easily drag and drop these methods along with decisions, delays and assignments to drive the hardware. Compile and simulate at the press of the button, making use of our renowned simulation and debugging technology to watch your design come to life on screen.Finally, transfer to the physical hardware with a single mouse click and see it working first time in the real world.
-
Product
LIMITER P-I-N DIODES FROM 0.7 TO 9.55 GHz
-
They prevent failure of of input amplifying stage of low-noise receivers with radio pulse power up to 5000 Watt. They can also be applied as seperate units without power supply and acting as controlled switches. This component is very valuable for radar applications because the high power transmitter and extremely sensitive receiver work with a single antenna.
-
Product
100μm Flexible Gold Interdigitated Electrode Chip (PI)
FIG1
-
Flexible gold IDE chip on a polyimide (PI) substrate for humidity, gas sensing, and optoelectronic research.
-
Product
PI Series Precision Line Infrared Camera
-
Experiencing real-time thermal images with a frame rate of up to 128 Hz, capturing and saving fast measurement results as snap-shots or video sequences or, thanks to the excellent thermal sensitivity, indicating even smallest changes in temperature – to only name a few of the many advantages.
-
Product
50μm Large-Size PI Interdigitated Electrode (IDE)
FPB1
-
50 μm large-size flexible polyimide (PI) interdigitated electrode (IDE) designed for humidity sensing, gas sensing, biosensing, and electrochemical research. Manufactured on a durable PI substrate with customizable electrode materials, dimensions, and layouts for laboratory, sensor development, and OEM applications.
-
Product
100μm Flexible PI Interdigitated Electrode Chip
FIC1
-
100μm flexible polyimide (PI) interdigitated electrode chip for gas sensing, biosensing, humidity monitoring, and electrochemical research.
