-
Product
Rugged PC Compatible
SYS-405S
-
The SYS-405S is a rugged, industrial system capable of operating at extended temperatures without requiring a fan or heat-pipe. The SYS-405S is based on the quad-core Intel® Atom™ E3815 processor and protected by a rugged enclosure.The SYS-405S includes dual Ethernet, dual MiniPCIe, USB 3.0, serial ports with RS-232/422/485 and two independent displays via DisplayPort, and/or Analog VGA.
-
Product
Hummingbird
-
Hummingbird features a Gigabit Ethernet connection, allowing acquired data to be streamed to laptop or PC. It can also be used as a standalone data logger, with its built-in CPU and disk drive.The unit is supplied in an ultra-rugged milled aluminium housing for use in close proximity to the test article.The Hummingbird is completely compatible with HGL's existing range of data acquisition, real-time monitoring, analysis and archiving systems.
-
Product
Advanced Telemetry System
HTS-SS
-
Our HTS-SS Advance telemetry sensor station works compatibly with all our existing sensors as well as the HTS-ETEMP, HTS-AS, HTS-VM and HTS-SM. Delivering on its name, the HTS-SS Advance provides more advanced telemetry capabilities than any other RC telemetry system and is capable of monitoring all types of models. It also provides engine temperature via the HTS-ETEMP sensor, air speed via the HTS-AS sensor, sensitive rate-of- climb tracking via the HTS-VM sensor and servo performance via the HTS-SM sensor. This leading-edge telemetry module provides the most reliable and comprehensive communication with your model yet. Expect More! Expect Hitec!
-
Product
RS232/422 Strobe Mux III Card & Panel
9565-16
-
16 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 7.6" high x 13" wide x 1" deep (193 x 330 x 25 mm).
-
Product
JadeFX Kintex UltraScale Processor and FMC Carrier - 3U VPX
Model 5983
-
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family BrochureVITA-57.4 HSFC FMC+ site offers access to a wide range of possible I/O- Supports Xilinx Kintex UltraScale FPGAs- 9 GB of DDR4 SDRAM- On-board GPS receiver- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- LVDS connections to the Kintex UltraScale FPGA for custom I/O- Optional optical interface for backplane gigabit serial interboard communication- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
Product
6-slot ATX-supported PICMG Bus Passive Backplane (vertical)
ATX6022/6VP4
-
*1 PICMG, 4 PCI and 2 ISA*Compatible with AX61222TP/AX61220TP*Supports ATX power supply*For 2U chassis
-
Product
250W to 500W - Single Output
GWS Series
-
*High Efficiency, up to 93%*1.6" height (1U compatible)*Wide Range AC Input*250W Convection Cooled*Five year warranty
-
Product
Software
DV-Win
-
An unique software application called DV-Win has been developed by DV Power as a tool compatible with all series of our instruments. Software automatically recognizes the device which is connected to a PC and activates appropriate form.
-
Product
RF Signal Amplifiers
-
The A10200 RF amplifier was designed to extend the power range of the Tabor arbitrary waveform generators and RF signal generators, yet it is compatible with many signal sources instruments.
-
Product
Additional Products: 26 Pin D-Type Cables - Connector to Connector
-
The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Clamshell Type Mechanical Fixtures
Series 30
-
Semco’s GR Series 30 mechanical kits are an inexpensive solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility.
-
Product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - XMC
Model 71760
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- Advanced reconfigurability features- VITA 42.0 XMC compatible with switched fabric interfaces- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
In-Line IR Sensor
ILA
-
10:1 Distance to Target Ratio, 32 to 932F. Dwyer Series ILA Non-Contact Sensors, measure temperatures from 32 to 932F (0 to 500C) and provide a linear 4 to 20 mA, 0 to 5 VDC or thermocouple output. The 2-wire signal is compatible with almost any indicator, controller, recorder, data logger, etc., without the need for special interfacing or signal conditioning.
-
Product
8-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB116
-
The FAB116 features a PICMG 1.3 CPU card slot, one PCIe x16 slot, three PCIe x4 slots, three PCI, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB116 is compatible with Axiomtek's AX60551 and AX60552 chassis.
-
Product
MAX31855 K-Type Thermocouple Sensor Breakout
SEN-30001-KDP
-
Breakout board for the MAX31855K digital thermocouple interface IC. Measured temperature range is -270C-1372C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 1x5 pin header and four mounting holes for standoffs and 4-40 screws. It does not contain a mini thermocouple connector.
-
Product
Additional Products: 68 Pin 1.27mm Pitch Micro-D Cables - 68 Pin to Unterminated
-
The connector to unterminated cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
Product
Industrial Grade PCI DIO 96 Board
MS 1817
-
*96 digital input/output lines*Support s all PPI Modes (Mode0, Mode 1 and Mode 2)*5 V TTL/CMOS*Compatible with NI DIO Card*2-wire handshaking capability*Known power-up
-
Product
GPIB Digital Interfaces
-
All of ICS's GPIB Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Product
NI-9423, 24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module
779009-01
Digital Module
24 V, 8 Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9423 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with 24 V logic levels, can accept up to 30 V discrete logic levels, and has an LED that indicates the status. The NI‑9423 offers isolation between the input and output banks from channel to earth ground. The NI‑9423 is a correlated digital module, so it can perform correlated measurements, triggering, and sychronization when installed in a CompactDAQ chassis.
-
Product
48" Stacking Banana Plug Test Leads
146-P
-
These test leads feature stacking banana plug jacks, with extended 48" length. These are great for establishing connections to diagnostic test points, while allowing the connection to be tapped with other instruments...2 way connections. These feature high flexibility wire and standard 4mm size banana jacks. You will receive one red test lead and one black test lead. These test leads are compatible with Electronic Specialties 146 and 147 test lead kits.
-
Product
NI-9478 , 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-02
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide … customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
Logic Analyzer Probes
-
Three probe types are available for GoLogicXL logic analyzers: flying leadset, Mictor, and Pinpoint probes. The Mictor and Pinpoint probes are compatible with similar Keysight/Agilent "soft touch" and Tektronix "connectorless" probes. All GoLogicXL probes are coaxially shielded and use passive termination inputs to prevent loading the device under test. Both differential and single-ended input signals are supported by all probes. Input voltage swings small as 300 mV are supported in single-ended mode, and 150 mV for differential signals.
-
Product
USB-TC01, 1-Channel Temperature Input Device
781314-02
Temperature Input Module
The USB‑TC01 is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take … temperature measurements with your PC. You can connect the USB‑TC01 to any USB port to use your PC as a display and monitor data in real time. The USB‑TC01 is compatible with J, K, R, S, T, N, E, and B thermocouples.
-
Product
Carbon Monoxide Detector Adapter
COA1
-
UEi Test & Measurement Instruments
The COA1 Carbon Monoxide Adapter plugs into compatible iOS® or Android™ mobile device to measure carbon monoxide levels.
-
Product
Waveguide Power Sensor
Q8486D
Power Sensor
Excellent SWR for reducing mismatch uncertainty50 MHz calibration port Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration Compatible with EPM (new N1913A/ 14A, E4418B/ 19B), EPM-P (E4416A/ 17A) and P-series (N1911A/ 12A) power meters, plus the E1416A VXI and discontinued 70100A and 43X power meter Accurate average power measurements over -70 to -20 dBm Frequency range 33 GHz to 50 GHz Diode power sensing element
-
Product
Data Acquisition PCI Card
UPC2100
-
The UPC2100 PCI Sensor Interface card provides real-world data acquisition and control for your PC. Up to 16 sensor inputs in any mix or combination are accepted by the UPC2100. No external signal conditioning is required. The UPC2100 includes configuration and data acquisition software and is compatible with C#, .NET, C++, Visual Basic, LabView.
-
Product
RS-232 Cable, 9 Pin (f) To 9 Pin (f)
34398A
-
The Keysight 34398A is an RS-232 cable, 9 pin (f) to 9 pin (f). Standard RS-232 cables are easy to find, but making them work is a different story. The Keysight 34398A has been verified for compatibility with Keysight's bench instruments to take the mystery out of RS-232 pinouts. The Keysight 34398A includes a 9-pin (f) to 9-pin (f) RS-232 cable and a 9-pin (m) to 25-pin (f) adapter.
-
Product
PXI Switching Instrumentation
Matrix
-
Marvin Test Solutions’ switch card portfolio includes matrix, multiplexer, and RF multiplexer configurations. 3U and 6U PXI switch cards feature easy to use, reliable, and integration-friendly D-sub style interface connectors – a feature unique to Marvin Test Solutions PXI switch cards. GENASYS switch cards are compatible with MTS’s family of GENASYS Switching and Switching/Digital Subsystems, featuring integrated MAC Panel SCOUT receivers.
-
Product
6-Channel VME Optical-to-Electrical Converter
V730
-
The V730 is a six-channel logic-level optical-to-electrical converter, packaged as a single-width, 6U VME module. When used with compatible Highland optical transmitter modules, the V730 provides fast, low-jitter, EMI-proof distribution of pulses, triggers, and precision timing signals.
-
Product
NI-9881, 1-Port C Series CANopen Interface Module
781673-02
Interface Module
The NI‑9881 is a high-speed CANopen interface for developing CANopen applications in LabVIEW software on CompactRIO hardware. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The NI‑9881 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. The NI‑9881 is compatible with only CompactRIO systems.
