-
Product
Full-Featured Data Acquisition with Isolation and High-Speed Measurement
EX1400 Series
-
The AMETEK VTI Instruments EX1400 Product family features the EX1401 and the EX1403A. The EX1401 adds isolation and high-speed measurement capability to the popular EX1000 Series of instruments, an advanced, full-featured data acquisition family designed to acquire precision data from temperature and voltage sensors. The EX1403A Precision Bridge and Strain Gauge Instrument sets a new standard for strain and bridge measurements, delivering the highest performance measurements possible while controlling overall test hardware costs. Browse each product below to learn more or request a quote.
-
Product
General Purpose Dual Flange Reaction Torque Sensor
TRS SERIES
-
The TRS Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. The anodized aluminum TRS Series is also available as a two axis sensor, torque and thrust, on special request. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenance and high cost of slip rings, bearings, and brushes.
-
Product
15-Pin D-Type Connector, Female
92-960-015-F
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Socket Wrench Torque Sensor Rotating Type
RSS SERIES
-
Our RSS Series rotating socket wrench torque sensors are available in ranges from 10 ft-lbs. through 250 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. Unlimited rotation of the ball bearing supported sensor shaft allows monitoring of the total fastening cycle. The sensing element incorporates bonded foil strain gages of the highest quality, along with coined silver slip rings and two silver graphite brushes per ring for data transmission.
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
ITA, G10, 10 Module, Removable Backshell, Keying Feature, With Protective Cover
410104272
ITA
The G10 ITA is equipped with a removable EMI-shielded cover. The cover slides up to provide access to wires and connectors and is secured by two screws. The removable and adjustable U-shaped cable clamps are attached by screws to the ITA frame and allows ITA modules to be pre-wired before assembly. The clamps can hold cable bundles with an oblong bushing effective diameter of 1.55". ITA strain relief plates are not needed.
-
Product
Strain Relief Plate, ITA, 90 Series
510109296
Strain Relief
ITA Strain Relief Plate works with all ITA modules. Plate is not needed for ITAs with cable clamps.
-
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
Extensometers for Indirect Tensile Testing of Asphalt
Model 3911
-
Jinan Testing Equipment IE Corporation
For indirect tensile testing, such as for resilient modulus, these extensometers measure the lateral deformation of specimens. They are self-supporting on the sample and clip on in seconds. The traditional way this deformation has been measured was prone to errors caused by slight rocking of the sample as it is loaded. The self-supporting design of the Model 3911 eliminates this problem. This unit will handle the dynamic pulse requirements of resilient modulus testing.The speed of mounting makes test set-up much faster than with the older method. The pivot mounting used ensures that the specimen contact pads meet the often uneven asphalt surface as well as possible. The measuring range options available allow a wide range of testing, yet can easily measure the sometimes very small displacements required.The Model 3911 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Digital Strain-Gauge Transducer
ZET 7010 DS
-
Digital small strain gauge sensor ZET 7010-DS transducer is purposed for tensile-compression control of concrete structures, it is used in SHM (structural health monitoring systems). These transducers can be used in stationary and mobile SHM systems.
-
Product
Shear Beam Force Sensors For Pull/push Direction
-
INELTA Sensorsysteme GmbH & Co. KG
Inelta Force Sensors operate with foil strain gauges
-
Product
34-Pin IDC Breakout, DIN Rail Mount, Screw Terminal
40-967-534-M
Breakout Board
This accessory is designed to be used for terminating a 34-Pin (0.050" pitch) Ribbon Cable Connector and includes a strain relief. The accessory is suitable for mounting on DIN rails.
-
Product
68-Pin SCSI Micro-D F to 2x34 Ribbon 2m
40-971-068-2m-FF
Cable Assembly
The 68-Pin SCSI Style Micro-D Cable Assembly is constructed from 2x34-Pin Twisted Pair cable with PVC insulation, terminating with 2x34-Pin polarised IDC connectors. Strain relief is provided via a metal spring latch on the 68-Pin connector.
-
Product
Low Power Analog to Digital
7430
-
Smart A/D for thermocouples, thermistors, RTD's, strain and pressure gauges8-channels of 16-bit A/D resolutionEliminates trimpot adjustments by using software calibrationPerforms concurrent 32-bit floating point operations to minimize host computer loadingEach channel is software programmable for sensor type, gain, low-pass filtering, scan rate
-
Product
20-Pin GMCT Male Connector, 10A, Without Backshell
92-960-020-10A-M
GMCT Male Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. It is supplied with removable solder bucket contacts suitable for wires up to 16 AWG. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
Strainer-Recorder
-
To ensure reliable operation of the measuring complex in the harsh conditions of ice tests, it is based on the industrial measuring platform NI CompactRIO, which provides mechanical strength and operation at negative temperatures.The system provides for operation both under the guidance of an operator with displaying the voltages removed from the ship's hull in the form of graphs on a computer screen connected to the strain gauge station via an Ethernet line, and in stand-alone mode, when the recording of a given duration is initiated by the station on pre-configured events: amplitude exceeding by one of channels, an external discrete signal or periodically at specified intervals.
-
Product
General Data Acquisition Device With Strain Gage Measurement
Spider-80SG
-
The Spider-80SG is a high precision, general purpose data acquisition device featuring strain gage measurement. This device can be used in a variety of physical and measurement tests. The Spider-80SG can acquire data from a strain gage or a wide range of measurement quantities. A variety of general purpose and strain gage based sensors are supported.
-
Product
Telemetry
-
Single channel system, offering wireless transfer of a single analogue signal, either 4-20mA or DC voltage. Mixed signal radio telemetry solution. Analogue I/O: 2x 2-40mA or DC Voltage. Digital I/O: 2x volt free or optional pulse counting required. Multi-channel radio telemetry system, 4 Analogue and 8 digital inputs. Significant signal connectivity and data transfer in a standard package.12 I/O channels allow greater signal monitoring capability SENSOR LINK Compact wireless telemetry link for any strain gauge sensor or RTD. Transmissions distance 1 to 300 meters. Licence free radio operation.16 bit ADC resolution.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 350
40-265-014
Simulator
This module simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems.
-
Product
PXI Precision Programmable Resistor Modules
-
Pickering's PXI precision programmable resistor modules feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques. This also means all resistance values can be set - there are no missing values due to switch resistance or resistor tolerance. These modules are ideal for sensor emulation applications that require very fine adjustment and also have the capability of being set as open or short circuit to simulate faults in cabling systems. The range includes modules specifically designed for RTD and strain gauge simulation.
-
Product
Rotary Torque Measurement System
-
Honeywell Industrial Automation
Honeywell's analogy telemetry rotary torque systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements.
-
Product
Coax, Module, Receiver, 20/26 GHz, 90 Series, 17 position, incl. strain relief plate
510104287
Receiver Module
(For use w/ 20/26 GHz contacts & SMA adapter. Includes strain relief plate)Primary mating module 510108240.
-
Product
Cable Tray, Slide Configuration, For Strain Relief And Cable Management, For 28" And Longer
310113424
Cable Tray
Strain Relief.
-
Product
Video Extensometers
-
The VE1 is a high precision video extensometer that uses a non-contacting optical measurement based on a digital camera and real time image processing to measure the longitudinal and transversal strain during tensile tests.
-
Product
4-CH 24-Bit Universal Input USB DAQ Modules (OEM Version Available)
USB-2401
Data Acquisition Module
The USB-2401 is a 24-bit, 4-channel simultaneous-sampling universal input USB DAQ modules featuring built-in signal conditioning circuitry, providing direct measurement of commonly used sensors including current output transducers, thermocouple, RTD, load cell, strain gauge, and others. Individual channels can be programmed to measure different signal types. The USB-powered USB-2401 is equipped with removable screw-down terminals for easy device connectivity, and the included multi-functional stand fully supports desktop, rail, or wall mounting.
-
Product
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" Depth
410112702
Enclosure
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" DepthIncludes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar may be removed to allow installation or removal of cables without requiring wiring to be disconnected from the assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 10A, 1m
A020GFR-F-0C100
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 1.5k
50-265-404
Strain Gauge Simulator
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 10A, 2m
A020GMR-C-0C200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
