-
Product
Specimen Preparation Equipment
-
Thermal damage can be reduced by cooling the specimen with liquid nitrogen during processing.Designed to suppress the consumption of liquid nitrogen, allowing long cooling periods.Rapid cooling of the specimen while immersed in liquid nitrogen. Return to room temperature. Designed to allow parts to be detached.
-
Product
Surface Water Absorption Tester
TF167
-
TESTEX Testing Equipment Systems Ltd.
Specimens are placed at an angle on the base of the apparatus. After water flows down the surface of each specimen, the amount of water retained by each specimen is measured. Six specimens are tested, three on the face of the fabric and three on the back of the fabric. The six observations are averaged to determine the surface water absorption of the fabric.
-
Product
Fabric Pneumatic Bursting Tester
TF142C
-
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
Product
Climatic Test Chamber
-
HIACC Engineering & Services Pvt. Ltd.
Optimised heating & cooling system offers higher performance & energy efficiency. The test chamber can be customised suiting to different test standards. It comes with larger viewing window, ports for live specimen testing, visual alarm system, improved mobility and smaller footprint.
-
Product
Concrete Comprission Testing Machine
CONCRETO 2000X/3000X
-
CONCRETO Series This compression testing machine can safely and efficiently perform tests at a high capacity without causing explosive fracture (failure of the specimen) on ultra-high-strength concrete, which is used as a structural material in high-rise buildings, etc. This one machine can be used for materials ranging from ultra-highstrength concrete to specimens that have been recently cast, mortar, etc.
-
Product
UV Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
1. Meet ISO,ASTM, DIN,JIS,SAE,BS,ANSI,GM,U.S.GOVT(ASTMG153,ASTMG154,,ASTMD4329,ASTMD4977,ASTMD4587,SAEJ2020,ISO4892)2. QUV condensation device simulates the effect of humidity of outdoor,meeting 100% humidity.3. Electronic-eye irradiance control system4. Use blackboard temperature sensor providing precise temperature and recuring test result.5. Perform humidifying, condensation and water spraying circulating test.6. Irradiance is calibrated by CR-10 calibrator and automatic calebration procedure.(Paten technology)7. Specimen size and quantity: 75mm×300mm 24pcs, 75mm×150mm 48pcs
-
Product
Wringer (Lab Padder)
TD110
-
TESTEX Testing Equipment Systems Ltd.
Laboratory Padder / Wringer, to evenly squeeze or extract excess liquid from fabric specimens for next procedure of test. This Lab padder / wriner is used for many kind of textile test to precisely ensures the rest liquid of specimens.
-
Product
Generators
Classical Shock
-
Software Classical shock is used for testing specimen resistance to shock impact. As the Software Classical shock is activated, at the output of shaker control system ZET 017-U there is formed a signal with pre-set parameters. Types of signals generated:
-
Product
Miniature Transverse (Diametral) Extensometers
Model 3475
-
Jinan Testing Equipment IE Corporation
A miniature extensometer designed for general purpose transverse or diametral strain measurements on small or thin specimens. May be used simultaneously with the Model 3442 miniature axial extensometers or the Model 3542 axial extensometers.
-
Product
Single Space Electro-hydraulic Servo Universal Testing Machine
WAW-F Series
-
Jinan Testing Equipment IE Corporation
WAW-F series single space Servo-Hydraulic Testing System Computerized is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The ultra-large testing space & dual-action actuator with longer stroke enable it to test not only standard specimen, but also longer ones with long elongation every so often. Equipped with the electronics, computer &software packages, it is capable of controlling the test procedures by the predetermined programs. The Servo-Hydraulic Testing System Computerized can also display, record, process and print the test results. The test curves can be drawn automatically in real time. The Servo-Hydraulic Tester of Single Space is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar, aircraft industry, research institutes, laboratories, calibration institutes etc.
-
Product
Wear Testing Machine
M-2000
-
Jinan Testing Equipment IE Corporation
Model M-2000 Wear Testing Machine is to be used test the anti-wear performance for metal and non-metal specimen under the sliding, rolling, and sliding-rolling condition. The Wear Testing Machine can also test various materials under dry-friction and wet-friction. The wear testing system can calculate friction work & friction coefficient by the data acquired. The Wear Testing Machine is widely used in universities, research & scientific institutes.
-
Product
SPI Flammability Tester (Vinyl Material)
TF318
-
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
Product
Digital Imaging
-
No one camera does it all. ACCU-SCOPE offers a wide selection of cameras for a variety of applications, and our experts can help you find the best match for your specific need. We have solutions from brilliant brightfield to low-light fluorescence, and from imaging living, moving specimens to fixed stained sections on slides. Need help deciding? Just ask!
-
Product
Pin Grips For Flat Specimens
-
Pin grips are very user friendly and are designed for conducting tensile tests of hard metal plate specimens that are difficult to grip. Specimens are held within the grips by passing pins through holes in the specimens.
-
Product
High Temperature Self-Supporting Furnace Extensometers (1200 C)
Model 3448
-
Jinan Testing Equipment IE Corporation
Epsilon developed this unique high temperature extensometer for testing metals, ceramics, and composites at the high temperatures produced by furnaces and induction heating systems. A combination of features make these extensometers easier to use and better in performance than other similar high temperature extensometers.The units are held on the specimen by light, flexible ceramic fiber cords. These make the extensometer self-supporting on the specimen. No furnace mounting brackets are required. The side load on the test sample is greatly reduced because of the self-supporting design and light weight of the sensor. Most materials testing furnaces with a side cut-out for an extensometer will readily accept a Model 3448. For induction heating systems, a different ceramic cord placement allows the extensometer to easily pass between the coils.The combination of radiant heat shields and convection cooling fins allow this model to be used at specimen temperatures up to 1200℃ (2200°F) without any cooling. An optional tiny air fan does enhance stability at the highest temperatures and is recommended for the highest accuracy and for tests with small elongations. The fan comes with a magnetic base for support so it can be mounted at any convenient location near the extensometer. Fan cooling is not generally needed for induction heated systems. High purity alumina ceramic rods are used. These are available in lengths as required to fit your furnace. A spare set is included with every extensometer. Specify chisel, vee chisel or conical contact points as desired.Most units operate equally well in tension and compression. Thus tensile, compression and cyclic tests like low cycle fatigue can all be performed with a single unit.For vacuum furnaces, special models are available. Epsilon can also provide a radiant heat transfer cooled version. This requires that the extensometer module be surrounded by a water cooled enclosure with a front slot for the ceramic rods.
-
Product
Manual Screw Flat Grips
-
Screw flat grips are general-purpose grips used for static tensile testing of a wide range of materials, most commonly, rubbers, plastics, textiles, and paper, and specimens such as plates and wires. Another advantage of these grips is they can be used to test thick specimens, up to 16 mm (0.63 in).
-
Product
Structural Testing Application Examples Using EDM Modal
-
Illustrated below are some customer applications in varying industries who are using the hardware and software by Crystal Instruments to analyze and understand the structural properties of their test specimen(s). Analyzing the modal characteristics namely natural frequencies, damping and mode shapes of the test unit further helps in improving the design to enhance the mechanical behavior of the test unit.
-
Product
Pneumatic Non-Shift Wedge Grips
-
Pneumatic non-shift wedge grips have an open-front design and use one-touch chucking by foot operation to provide simple specimen mounting. These grips are suitable for tensile testing materials such as plastics and metals.
-
Product
Micro durometer
MD-1 Capa
-
High-precision measurement of micro-sized specimens with a Fully-automatic Micro Hardness IRHD System. simple operation. A hardness tester for thin and small specimens of various rubbers, thermoplastic elastomers, nonrigid plastics. Unlike conventional durometers, it enables direct measurement of the hardness of objects with higher reproducibility.
-
Product
Scanning Electron Microscopy
SEM
-
Materials Evaluation and Engineering
JEOL JSM-6610 LV LaboratoryScanning electron microscopy (SEM) uses electrons for imaging to obtain higher magnifications and greater depth of field than light microscopes. The instruments at MEE are capable of variable-pressure, or low vacuum, SEM (VPSEM), as well as traditional high-vacuum conditions for sample observation. VPSEM is a specialized method using a variable-pressure sample chamber that allows direct evaluation of samples that are not readily examined with a traditional high-vacuum SEM. Nonconductive or vacuum sensitive samples that would typically require additional sample preparation can be directly analyzed in VPSEM without the need for additional sample preparation, such as carbon or metallic conductive coatings. This reduces both sample preparation time and distractions in microanalysis. Our laboratory also has a field emission SEM (FESEM) for critical high-magnification work and low-voltage (LVSEM) applications. Each instrument has a spacious sample chamber that can accommodate large and irregularly-shaped specimens and accessories for feature dimensional analysis and chemical microanalysis.
-
Product
Horizontal Flammability Tester
-
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
Product
Ion Beam Milling Systems
-
When material specimen surfaces are prepared for SEM or incident light microscopy, the specimen usually undergoes multiple processes until the layer or surface to be analyzed is machined with precision. Leica Microsystems’ workflow solutions for solid state technology cover all steps required for demanding high-quality sample preparation.
-
Product
Paper Thickness Tester
DRK107A
-
Shandong Drick Instruments Co., Ltd.
DRK107A Paper Thickness Tester is professionally applied to testing the thickness of paper specimens.
-
Product
Electrodynamic Vibration Test Systems
CV-series
-
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
Product
Secondary Ion Mass Spectrometry (SIMS Analysis)
-
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
Product
Rubber Plasticity Meter
DRK209
-
Shandong Drick Instruments Co., Ltd.
DRK209 is applicable to test plasticity property when the specimen bears 49N pressure. The meter is used to test plastic value and restoration value of raw rubber, plastic rubber and rubber.
-
Product
Automatic Capacitance and Tan Delta Bridge
-
*Automatic Microprocessor controlled Guarded Bridge Circuit.*Suitable for testing at voltages up to 500kV.*Can be used to measure both Grounded and Un-Grounded Specimens.*Automatic guard circuit for three-terminal measurement.*Interface measurement and automatic interference suppression circuitry.*Optional range Extension Transformer for large capacitance values.*Test data storage facility.*RS-232 computer interface and USB printer interface.*Window Interface Software for data transfer.
-
Product
Vertical Flammability Chamber
TF312
-
TESTEX Testing Equipment Systems Ltd.
Comprises a draft free stainless steel flammability chamber with observation window for easy test viewing. Specimen holders, burner and associated hardware are dependent on the test standard and must be specified.
-
Product
Concrete Water Impermeability Tester
-
The concrete water impermeability testing system is designed with many different standards in mind including DIN 1048, ISO/DIS 7031, EN-12390-8 & UNI 9533. This impressive piece of machinery comes in different models with either 3 or 6 measuring points and with or without quantitative measurement of water permeability. The supporting structure is very stable and is at a convenient height to allow the easy access. The pans are made out of stainless steel, the specimens are easy to insert due to the clamping device.
-
Product
Concrete Bulk Resistivity
RCON
-
Giatec RCON™ is a non-destructive device for measuring the electrical resistivity of concrete specimens in the laboratory without any additional sample preparation requirements. This measurement can easily be made on the same concrete samples that are currently used for the compressive strength testing of concrete.
