Crystals
-
Product
Quartz Crystals
-
Quartz crystal resonators are used in a wide range of electronic applications that require timing devices. The quality of the quartz crystal blank is critical to the performance of quartz crystal units and the high Q factor of quartz means that tight stabilities can be achieved; this is key to ensuring microprocessor timing circuits work correctly within customer’s designs.
-
Product
Electro-Optic DAST Crystals
-
DAST and other high-quality organic crystals are produced and optically prepared in the facilities of Rainbow Photonics in Switzerland.
-
Product
Differential Quartz Crystal Microbalance
Dike
-
During an experiment to detect an affinity reaction on biological material, a molecule of interest is attached to the quartz crystal of the measurement channel, this deposition can be achieved by direct binding or by capture through another protein, the result of this process is to make the quartz sensitive to the molecule to be detected.
-
Product
Four And Two-Port Multi-Protocol RS-232/422/485 PCI Express Mini Cards
mPCIe-COM-4SM Family
-
The mPCIe-COM-4SM family of cards feature high performance 16C950-class UARTs. Available in 4-port and 2-port versions, each port is capable of communication speeds up to 921.6kbps in RS-232 (differential modes support speeds as high as 3Mbps) and has 128-byte deep transmit and receive FIFOs. Large FIFOs protect against data loss in multitasking operating systems, reduce CPU utilization, and improve data throughput, while reducing or eliminating inter-character or inter-packet pauses. The advanced integrated circuit with pre-scalar supports a wide variety of custom baud rates, and any rates not otherwise achievable can be supported via a custom factory-installed crystal oscillator (up to 10Mbps!).
-
Product
Pressure Fittings
-
AMETEK Sensors, Test & Calibration
Our CPF Fittings & Hose are a new line of quick-test pressure fittings for calibration & test applications - designed with an emphasis on safety. Crystal Pressure Fittings (CPF) perform up to 10 000 psi / 1000 bar, and feature a safety weep hole to alert you before you accidently disconnect from a pressurized system. It can also be used as a bleed point. CPF fittings seals two ways: use fingers for an o-ring seal or use a wrench for a metal to metal cone seal (good to -40°C).
-
Product
Analytical Services
-
IGC: Inverse Gas Chromatography; Understand surface energies, polarities, acid/base properties and nanomorphology on powders and fibers. ToF-SIMS: Time-of-Flight Secondary Ion Mass Spectrometry. Localize your molecules at the first nanos! 2D imaging with resolution up to 200 nm. Highest sensitivity up to 10 ppm. CM: Quarz Crystal Microbalance In-situ observation of thickness and stiffness of any films in liquid environmentSEM: Scanning Electron Microscopy Images say more than words, especially with an artistic eye XPS/ESCA: X-ray Photoelectron Spectroscopy/Electron Spectroscopy for Chemical Analysis.
-
Product
Frequency Synthesizer-Detector
SD-31
-
The Model SD-31 Synthesizer-Detector is a high output crystal signal generator of precisely known frequency combined with a sensitive, selective detctor for RF bridge measurements of AM antenna impedance. Packaged in a single light-weight battery-powered unit, the SD031 complements bridges such as the General Radio 1606, 916, and the Delta OIB-1.
-
Product
Fiber Optic Talk Set
TT1315
-
The Yamasaki TT1315 Fiber Optic Talk Set is designed to achieve crystal clear, full duplex, hands-free communication over any spare singlemode fiber optic cable. Sold as a two pack, these talk sets give fiber optic installers and technicians a reliable and cost effective solution to communicate over long distances for a long period of time, whereas RF devices can often be a costly and ineffective option. The Yamasaki TT1315 Fiber Optic Talk Set is a breeze to use with a simple menu system, automatic call detection, user-selectable back light, flip-out stand and comfortable headset.
-
Product
Moisture Analyzer Series
3050
-
The 3050 series of moisture analyzers utilizes AMETEK’s proven, accurate quartz crystal microbalance (QCM) technology. Built-in verification provides operators with increased measurement confidence.
-
Product
Phase-Locked Crystal Oscillator
PLXO Series 0.9” x 0.9” x 0.25”
-
*Compact Surface Mount Package *Excellent Phase Noise and Stability *Configurable for any application
-
Product
Route Based Vibration Data Collector
-
The Crystal Instruments CoCo series are portable devices for vibration monitoring and predictive maintenance applications. The system consists of a CoCo analyzer and the Engineering Data Management (EDM) software. The CoCo is used to make field measurements and the EDM software in Vibration Data Collector (VDC) Mode is used to setup the CoCo hardware and define routes before field measurements, and to download data from the CoCo to analyze and archive afterwards.
-
Product
Open-Source Quartz Crystal Microbalance
-
The sensor is a surface sensitive quartz crystal capable of measuring phenomena at molecular scale. It works in vacuum, air and liquid environments. The QCM sensor is based on the piezoelectric properties of the quartz crystal. The application of an alternating current causes the mechanical vibration of the quartz crystal in the MHz range. The QCM technique measures the variations in quartz frequency for measuring the mass variations on its surface.
-
Product
Structural Testing Application Examples Using EDM Modal
-
Illustrated below are some customer applications in varying industries who are using the hardware and software by Crystal Instruments to analyze and understand the structural properties of their test specimen(s). Analyzing the modal characteristics namely natural frequencies, damping and mode shapes of the test unit further helps in improving the design to enhance the mechanical behavior of the test unit.
-
Product
XRT Source Brighthawk
-
The BRIGHTHAWK NT100 is a performance-leading microfocus X-ray tube comprising proprietary technology to achieve a high brightness output. The tube consists of a LaB6 crystal source for generation of the electron beam, a magnetic beam steering system, and a tungsten target for X-ray photon emission. The components are mounted in a precision-engineering housing and held at ultra-low vacuum levels for long-life performance. Following on from the successful 3rd generation tube, this 4th generation of tube across a wide energy range from 30 kV to 160 kV is highly configurable through a software interface to the internal control board, which is connected via an optical interface (through an Ethernet converter).
-
Product
Three Phase Din-rail Multi-rate kWh Meter
SY 1041
-
Hong Kong Songyang Industrial Ltd.
Type SY1041 three phase DIN rail watt-hour meter is a kind of new style three phase electronic multi-rate watt-hour meter, energy data display adopt 7 digits wide temperature type crystal display, with many functions of multi-rate (time-of use) energy measurement, infrared carrier wave communication and RS485 serial port communication reading meter, etc
-
Product
System
SYS-24
-
The system shown here was built for a customer to be used in metallization, a common use for many smaller systems. It is also fully capable of performing optical coatings when equipped to do so. This particular system came equipped with a 16" APD ISO Flange mounted cyropump, and a Varian tri-scroll for roughing. The cooling tubes for the crystals as well as the drive motor for the parts holder can be seen on the top of the chamber.
-
Product
"Extremely Random" Precision Noise Generator
Model 3025
-
The Model 3025, "Extremely Random"TM Precision Noise Generator supplies White and Pink Noise, and a 1 kHz reference signal. Crystal controlled - the pseudo random circuitry provides a 6.5 Day pseudo-random cycle time, assuring a "Extremely Random"TM noise source.
-
Product
Frequency Monitors
FM Series
-
FM Series line-powered frequency monitors are high quality, dependable panel meters designed to continuously monitor line power frequency. Crystal reference-based for high accuracy, these 1/8 DIN/NEMA case style meters come with LED or LCD displays.
-
Product
Strip-Line™ Socket with Bifurcated Contact Wire Wrap Pins
Series 0501
-
Strip-line Sockets with Bifurcated Contact Wire Wrap Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in wire wrap or solder tail pins. Consult Data Sheet No. 12008 for solder tail pins.
-
Product
Portable Carrier Demodulator with Digital Display
CD379
-
The CD379 is a portable, completely self contained digital transducer indicator. In addition to the front panel liquid crystal digital display, the unit also provides a 2 Vdc analog output suitable for recording, remote display or control purposes. The unit is for use with all variable reluctance transducers and features solid state electronics, 3 1/2 digit liquid crystal display and battery pack with six 1.5V penlight cells for truly portable operation. The unit can also be powered from an external DC power supply or AC battery eliminator (converter) module.
-
Product
Phase Noise Measurement Solution, 50 kHz to 110 GHz
E5505A
-
The Keysight Technologies E5500 Series of phase noise measurement solutions offers the most flexible set of measurements on one-port VCOs, DROs, crystal oscillators and synthesizers. Two-port devices, including amplifiers and converters, plus CW, pulsed and spurious signals can also be measured. The E5500 measurements include absolute and residual phase noises, AM noise, and low-level spurious signals. The stand-alone instrument architecture easily configures for various measurement techniques, including the PLL/reference source technique, residual and FM discriminator methods.
-
Product
Digital Meter
-
Electronic devices that display measurements such as voltage, current, and resistance on a liquid crystal display.
-
Product
Stopwatches + Timers
-
Sper Scientific professional laboratory stopwatches and timers use only highly accurate quartz crystal movements. All models are available with an N.I.S.T. traceable Calibration Report.
-
Product
Board
Arduino Mega 2560 Rev3
-
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started. The Mega 2560 board is compatible with most shields designed for the Uno and the former boards Duemilanove or Diecimila.
-
Product
MicroImagerTM
Exicor®
-
The Hinds Birefringence Imaging Microscope is ideal for measuring birefringence in biological structures, glass, crystals, and many other organic and inorganic samples.
-
Product
Measuring & Analysis Equipment
-
Quality management for semiconductor manufacturing processes and liquid crystal panel manufacturing processes, which require nano-order precision. Oxygen analyzers used in firing furnaces and N2 reflow ovens.Water quality meters used to monitor the water quality of plant discharge and the pure water used in semiconductor manufacturing processes.Our measuring and analysis equipment is used in a wide range of fields.
-
Product
Quartz Crystall Oscillators
-
Superior crystal oscillator precision is required for both time and frequency in precision instrument applications such as synthesizers, counters and spectrum analyzers.
-
Product
1 kW and 2 kW Laser-Based Floating Zone Furnace
Laser Furnace
-
The 1 kW and 2 kW laser furnace for single crystal fabrication is based on a design and developed in close cooperation with the RIKEN Center for Emergent Matter Science under the leadership of Yoshio Kaneko. Both melting zones have 5 lasers each, which guarantees a high uniformity of power density in the melting zone range. The laser profile has been optimized to reduce thermal stress during the crystal growth process. In addition, the system includes an integrated temperature sensor for real-time temperature monitoring. Temperatures up to 3000 °C can be reached and therefore materials with a very high vapor pressure, a narrow temperature range of the melt, a high thermal conductivity coefficient and incongruent melts can be melted.
-
Product
Grain Inspector
iS-G1
-
The iS-G1 is a full line speed optical module for the inspection of crystal grains.Using our new grain imaging technology, the iS-G1 is able to inspect as cut wafers at full inline speed with no need to stop the conveyor belt. Automated algorithms analyze the grains and report metrics.
-
Product
2- and 4-Mirror Floating Zone Crystal Furnaces
IR Image Furnace
-
The high-performance, compact IR Image Furnace from Quantum Design offers unsurpassed performance in a convenient, stand-alone design. Rivaling much larger and more costly IR furnaces, it uses the Floating Zone (FZ) method to promote single crystal growth from a polycrystalline rod. This method has been shown to be extremely effective for a wide class of materials. Now, more easily than ever before, you have the ability to synthesize superior quality single crystal specimens in your own laboratory. This furnace is available in both 2- and 4-mirror versions.
