-
Product
Interface Panel for SLSC
THROUGHPOINT™
Interface
Bloomy's ThroughPoint™ Interface Panel provides a simple, yet highly-flexible connection between the unit under test and resources in a National Instruments Switch/Load/Signal Conditioning (SLSC)-based test system.
-
Product
AC Fuel Flow Signal Generator
TA-100
-
The TA-100 signal generator was designed to facilitate testing of aircraft fuel flow indicators that require two input signals designated as “Drum” and “Impeller”. This generator provides both signals so as to provide a direct interface to the fuel flow indicator under test. The generator also provides switched power out to the unit under test as well as a 5v source for testing the bezel lighting. The original design was built around the requirements for the AMETEK series indicators (pn: 10171 series). This generator simulates a reference and a time delayed signal of appropriate amplitude for an indication of up to 1200pph for the indicator under test. The “PPH Select” switch provides fixed signal delays representing 0, 200, 400, 800, 1000 and 1200pph flow rates respectively, this provides the mechanic with an expedient check of the indicators accuracy. The “PPH Adjust” control allows the mechanic to vary the signal delay throughout the full range and serves as a good method for checking of pointer smoothness from stop to stop. The unit’s front panel also provides test jacks to monitor the “FDR Output” as well as the drum and impeller signals. The TA-100 requires only 28Vdc to operate. This generator provides a very economical approach to any repair facility or flight department as it becomes an alternative to purchasing two bench top signal generators. The TA-100 generator at the very least can provide a simple functional test and eliminate the high cost of exchanging an indicator as a function of troubleshooting the aircraft system.
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
Matrix Switch Module
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
MTA Wiring Analyzer
2650
-
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
Product
Quality Control
Sandwich Box
-
Housed in a ruggedized box, the VQC Sandwich Box is a field-proven acquisition unit for testing all aspects of vibrator performance, providing real time display of accelerometer and reference signals during the sweep.
-
Product
UPG-07 - Ultrasonic Precision Gages - Monochrome
UPG-07 Monochrome
-
PG-07 Series of hand held ultrasonic precision gages are available in 4 models. Our UPG-07 series is the ideal unit to non-destructively test the wall thickness for manufactured parts requiring unprecedented accuracy and resolution. The UPG-07 series utilizes single element transducers and offers a 30 Mhz, square wave pulser, .0001" or 1 micron resolution with the ability to store and re-call 30 unique applications. So if you are measuring light bulbs, plastic bottles, golf clubs, coil steel, thin aluminum, aircraft parts and even pure gold bars, the UPG-07 series is the right choice.
-
Product
SWB-2815, 4x86, 0.3 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-15
Reed Relay
4x86, 0.3 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2815 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781420-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Automated Functional Testers
-
Don Alan testers are compact integrated systems with very few if any connected instruments. This reduces the unit cost of the test systems dramatically. With the lower unit cost, more test systems can be made available. Having more testers provides redundancy and higher throughput and allows duplication of the same test process in house by the customer. This means the customer can effectively handle warranty return issues on the spot (the retest results get tied to the original test results for warranty analysis). It also allows customers to do sample based quality assurance.
-
Product
Bi-Axial or Axial Averaging Extensometers
Model 3560
-
Jinan Testing Equipment IE Corporation
This extensometer is ideally suited for testing anisotropic materials such as advanced composites as well as for general purpose tests like determining Poisson’s ratio. The Model 3560BIA uses a design unique to Epsilon, where the knife edges remain parallel during the displacement. This approach greatly reduces crosstalk between axes and allows use on round or flat specimens with equal ease. These extensometers are very easy to mount. Integral springs hold the unit on the test sample. The parallel multiple flexure design makes these units very durable.The Model 3560AVG reads axial strain only as a single averaged output. It may also be supplied with two independent outputs, one measurement from each side of the specimen. This set-up is most commonly required when an indication of specimen bending is desired. The second version, the Model 3560BIA, includes both the averaged axial strain and the transverse strain. Again, this may also be configured as dual independent axial readings, which results in a three channel extensometer.The Model 3560 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
SM / Expansion Unit
-
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
Product
C++ Test Framwork
Google Test
-
a unit testing library for the C++ programming language, based on the xUnit architecture. It can be compiled for a variety of POSIX and Windows platforms, allowing unit-testing of C sources as well as C++ with minimal source modification.
-
Product
Electricians' Accessories
-
A selection of voltage detectors, proving units, test leads, certificate books and a DVD, which make it that bit safer and easier to get the job done.
-
Product
Java Testing, Static Analysis, Code Review
Jtest
-
Parasoft Jtest is a complete Java developer's quality suite for static code analysis, code review, automated unit and component testing, coverage analysis, and regression testing ? on the desktop under leading IDEs and in batch processes.
-
Product
Glove And Sleeve Testing Equipment
-
Hanco's glove and sleeve test units are designed for the ultimate in convenience, efficiency and performance. The unit's versatility is unmatched. Each unit is equipped to test Class 00 through Class 4.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781420-33
Relay Matrix Module
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Atec Dyna
-
Macro-instruments an innovative concept : ultra-simple interface between the test bench and the equipment being tested, Software-controlled macro-instrument, Generic TUA (Test Unit Adapter) incorporated in the bench
-
Product
Exclusive and Tailored Software Testing Services
-
Choose from our wide span of software testing services to assure high quality and reliable software. From unit testing to comprehensive regression testing, we cater to all your QA testing needs.With us, get assured of getting maximized performance and enhanced scalability, and tame the first step to empower your website with our next-generation software and web testing services. From handling complex projects to identifying the slightest bugs (which sometimes are most difficult to spot), we are specialists in coordinating with small, medium, and large-scale enterprises.
-
Product
Safety Valve Test Bench
-
Nagman Instruments & Electronics Pvt. Ltd
Safety Valve Test Bench is a very easy, safe, accurate and maintenance free operating work shop test unit for Testing & Calibration of pressure/safety relief valve.
-
Product
Professional Cable Tester/Tracer with Tone Generator
TC-NT2
-
The TC-NT2 is a convenient and comprehensive cable tester for network professionals. Its powerful and user-friendly features enable network installers to accurately check pin configurations of various voice and data communication cables. The TC-NT2 includes a master unit that transmits test signals to its corre-sponding remote terminator to verify cable reliability
-
Product
Structural Testing Application Examples Using EDM Modal
-
Illustrated below are some customer applications in varying industries who are using the hardware and software by Crystal Instruments to analyze and understand the structural properties of their test specimen(s). Analyzing the modal characteristics namely natural frequencies, damping and mode shapes of the test unit further helps in improving the design to enhance the mechanical behavior of the test unit.
-
Product
Parametric Test Fixture
U2941A
Test Fixture
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
Cable Testers
E447
-
Similar to E445 but without jack and RCA (phono) testing facilities. Includes special XLR remote unit to enable testing of cables where it is not possible to bring both ends to the tester.
-
Product
Induced Signals Test
-
The test relates to interfering signals that may be generated by interconnected equipment. Induced signal testing is used to determine if equipment will withstand various signals, such as might be introduced by failures in other equipment to which the test unit is connected.
-
Product
Coil Analyzers
SAT Series
-
The Coil Analyzers SAT30A and SAT40A are powerful, lightweight units ideal for testing of circuit breakers. Substation battery is not connected or available. The SAT series instruments are intended to supply circuit breaker coils and spring charging motors. They spring charging motors (SAT40A – AC and DC) as a part of commissioning and maintenance testing.
-
Product
Intermittent Fault Detection & Isolation System
IFDIS
-
The IFDIS™ uses patented Intermittent Fault Detector technology that simultaneously and continuously monitors every circuit path within a Unit Under Test (UUT) - such as a Line Replaceable Unit (LRU) chassis' interconnects - for intermittent continuity failures that occur for as short as 50 nanoseconds. This state of the art technology is combined with an environmental chamber and vibration table, which simulate the UUT’s operational environment and cause intermittent faults to manifest, creating a system that is unsurpassed in intermittent fault detection.
-
Product
Pressure Decay Test Systems
-
Pressure decay leak testing technology has become a mainstay in the arena of high volume production testing. Pressure decay testing methods offer the world's manufacturers a cost-effective and easily applicable solution to the leak testing challenges they encounter on a given day. Fundamentally, pressure decay testing is a straightforward measurement technique; Cincinnati Test Systems (CTS) pioneers new and innovative ways to integrate our technology into custom turnkey systems that exceed the industry standards for reliability and repeatability. CTS' 30+ years of experience goes way beyond the pressure test unit by offering our customers comprehensive, custom turnkey solutions to the most challenging leak testing problems.
-
Product
ITA, G12, Front Mount, 12 Module With Protective Cover
410104322
ITA
The G12 ITA can be used with all G12 Receivers. The ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC Enclosure or customize your own fixture to be attached to the ITA. These are front mounted for ease of installation. A wide range of ITA modules are available separately for user configuration.
-
Product
RF Microwave Switch Matrices
-
RF Microwave Switch Matrices provide automatic routing of RF microwave signals between test instrumentation and the unit under test (UUT). They provide consistent signal paths, enable automation of tests, and often include signal conditioning.
-
Product
Torque Measuring and Monitoring System
WISER 4000
-
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
