-
Product
Voyager Intermittent Fault Detection Tester
-
This family of testers is available as the portable VIFD™ tester (previously called the Ncompass-Voyager) with 128, 256 or 512 test points, and it is available as a 19” rack-mount system – the IFD & Isolation System (IFDIS™) – with thousands of test points. Testers are available from Copernicus Technology for purchase or lease. Alternatively we can provide the full test service for you and we also provide all the corresponding test accessories listed under the Test Equipment menu button.
-
Product
PCB Test Points and Terminals
-
Our PCB test points and terminals feature a large loop for easy probe attachment or to facilitate the clipping on of other components. They are ideal for components which need frequent replacement and are also suitable for raising hot components above the surface of the PCB.
-
Product
Benchtop Automated Functional Test
midUTS
Functional Test
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
Product
Benchtop/Portable Cable/Harness Wiring Test System
CKT1175-10
-
Designed for wiring testing requirements requiring up to 2,000 test points, the CKT1175-10 is ideal as a benchtop or portable test system. The system is packaged in an enclosure specifically designed to be used in rugged environments. The basic 500 test point system is 20.5 in. (521 mm) wide X 12.0 in. (305 mm) high X 16.05 in. (408 mm) deep; the 500 test point expansion units are 20.5 in. (521 mm) wide X 6.00 in. (153 mm) high X 16.05 in. (408 mm) deep.
-
Product
Test adapter LRP-LR (Type D, 4 mm)
MA-LPL02D
-
Hachmann Innovative Elektronik
Our test adapter MA-LPL02D connects LR measuring devices to standardized LRP string parts and capacitive test points. An insulating tube with great dielectric strength shields the user from static energized test points without automatic earthing.
-
Product
High Voltage Differential Probes
-
A high voltage differential probe is used for measuring the voltage difference between two test points where neither test point is at ground. High voltage differential probes from Tektronix can be used for signals up to 6000 V. These probes are the best choice for making non-ground referenced, floating or isolated measurements in large part due to their common mode rejection capability. These products are designed, manufactured, and serviced by Tektronix.
-
Product
Function Test and In-Circuit Test
CT350
-
ICT test points: max 2736 CAD Data import Automatic program generator Powerful debugging tools Test coverage analysis Paperless repair station Logging- and statistic functions Full graphical functions Panel and multisite tests Fast adapter exchange High Pin Count-Interface On table optional usable shelf part.
-
Product
Drive-Thru Feature, GTE 10.00p
K8218A
-
The DriveThru feature enables the test development software to test integrated circuits or connectors when there are no test points assigned between the resistor and the device.
-
Product
MTA Wiring Analyzer
2650
-
DIT-MCO's newest test solution, the Model 2650, incorporates modularity so that the system conforms to your testing needs. The modular switching units can rack-and-stack in a cabinet providing concentrated test points or can be distributed around the Unit Under Test (UUT) eliminating long, cumbersome adapter cables. Or you may reconfigure the system at any time when your needs or the UUT changes.
-
Product
2-Axis Rate and Position Tables
-
When a device under test needs to be stimulated with simultaneous movements around two axes, then a product from the ACUTRONIC two-axis motion simulator range is the right choice. Due to their independent motion simulation in two axes they are very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
Flash Point
-
At which temperatures will your sample burn, ignite, or cause fire? How are your flammable liquids composed, and what are their properties? Volatility is directly related to a substance‘s flash point temperature (flammability). Anton Paar’s flash point testing equipment safely and easily determines the values you require for the processing, storage, transportation, and classification of dangerous liquids.
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Digital Communication Trainer
-
Digital Communication Trainer System to understand Techniques of Digital Modulation & Demodulation.Various functional block diagrams are provided on-board for Teaching/Training. These Trainer provides with various Test Points to visualize the signals on Oscilloscopes.
-
Product
Multiplexers
-
Capable of performing the necessary switching between test points of the device under test, to give access to low frequency measuring instruments, in electronic test systems based on tool receivers.
-
Product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
-
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
Matrix Switch Module
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
3-Axis Motion Simulators
-
When a device under test needs to be stimulated with simultaneous movements around three axes, then a product from the ACUTRONIC three-axis motion simulator range is the right choice. Independent motion simulation in three axes makes them very versatile: they are used as Inertial Guidance Test Systems (IGTS), for HardWare-In-the-Loop (HWIL) testing, for the test of optronic pointing devices, and many more applications.
-
Product
FM Tokenless Transmitter & Receiver
MS 1522
-
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
Product
SWB-2810, 4x43, 1 A, No Row Access, Reed Relay Matrix Module for SwitchBlock
781421-10
Reed Relay
4x43, 1 A, No Row Access, Reed Matrix Module for SwitchBlock - The SWB‑2810 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2814, 8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock
781421-14
Matrix Switch Module
8x9, 1 A, 2-Wire Reed Matrix Module for SwitchBlock - The SWB‑2814 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Very High Density Fiber Tap
Flex Tap VHD
-
Keysight Network Applications and Security
Flex Tap VHD is a modular, very high density fiber tap available, offering up to 36 taps in a 19 inch 1U space, to reduce IT costs while helping ensure availability of security and business critical applications. Network taps (test access points) are a key part of the access layer of a visibility architecture because they are an unobtrusive way to capture monitoring data. They offer comprehensive traffic visibility for network monitoring and security tools that do not introduce points of failure in the network. Ixia has a large variety of network taps on the market today, offering speeds from 1Gbps to 100Gbps, single and multi-mode, as well as different fiber types and support for Cisco bidirectional (BiDi) transceivers.
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
CAM/TRAC Test Kits
Series 47
-
The VP Series 47 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 47 provides interface compatibility using the Virginia Panel ITA G12 interface. The ITA frame is offered as an option for those wanting to provide their own ITA Interface.
-
Product
9 Pin Breakout Interface
VSI-Breakout-9
-
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
SWB-2811, 8x21, 1 A, Reed Relay Matrix Module for SwitchBlock
781421-11
Reed Relay
8x21, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2811 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Backplane Test System
402HV
-
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
Product
Pressure Test Points
Minimess
-
Minimess test points offer a uniquely simple method of accessing low or high pressure systems for the purpose of pressure testing, oil sampling or gas charging. Developed by Hydrotechnik more than 50 years ago, they are found worldwide in hydraulic, process and gas systems. These pressure test points offer the most advanced sealing system available with working pressures up to 630 bar.
-
Product
SWB-2834, 8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781420-34
Relay Matrix Module
8x34, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2834 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Passive Fiber Network TAPs
-
Passive network test access points (TAPs) are a hardware tool that allows you to monitor your network. Garland Technology offers fiber network TAPs in network speeds of 1Gb, 10Gb, 40Gb and 100Gb. Fiber Network TAPs are passive, purpose-built hardware devices that make a 100% copy of your networks data - without affecting network traffic. Passive network TAPs let your monitoring tools to see every bit, byte and packet®.
