Digital Pattern Generators
-
Product
Multi-Channel 12-Bit, 5 GSPS Digitizer
ADQ36
Digitizer
ADQ36 offers software-selectable two- or four-channel configuration with 5 or 2.5 GSPS sampling rates respectively. The programmable DC-offset makes it ideal for sampling unipolar signals.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 180 MS/s on 2 Channels, 2 Single-Ended Inputs
DN2.447-02
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 2 Channels
M4I.4450-X8
Digitizer
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 5 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5912-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
Non-Isolated Digital I/O DAQ Cards
Digital I/O Module
PCI/PCIe-bus non-isolated digital I/O cards for parallel data transfer, TTL DIO, and logic signal sensing.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785167-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PCI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Output, Bank-Isolated Digital I/O Device
778836-01
Digital I/O Module
The PCI-6514 is an industrial digital I/O interface, with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in … software, to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PCI-6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PCIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4I.2220-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
4.5 Digit, 150 Meas/Sec True RMS Digital Multimeter
T3DMM4-5
Digital Multimeter
4.5 Digit, 150 Meas/Sec True RMS Digital Multimeter.
-
Product
PXI 32 Channel I/O, High Side Driver
40-413-001
Digital I/O Module
A 32 channel Digital I/O module with high output voltage and currentcapability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only (shown here), alow side only and a combined high and low side each capable of driving 2A loads. Eachoutput is fully protected against over-voltage, over-current and thermal overload,ensuring robust and reliable operation in the toughest test environments. For highside voltage driving the high side voltage source is supplied from an external voltagesource, permitting the module to drive high capacity loads without impacting thePXI chassis power supply.
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
NI-9425 , 24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module
780176-01
Digital Module
24 V, 32-Channel (Sinking Input), 7 µs C Series Digital Module - The NI‑9425 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels. The NI‑9425 offers isolation between the input and output banks from channel to earth ground. You cannot use the NI‑9425 in a CompactDAQ chassis to perform counter operations.
-
Product
PXIe 8 Bit High Speed Digitizer - 2.5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2220-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O Module
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
16 Bit Waveform Generator
PA72G16400
Waveform Generator
The PA72G16400 is a 16-bit arbitrary waveform generator, capable of generating waveforms at speeds up to 400Msps. The high resolution and the high sample rate allows generating signals with very low quantization noise levels. An onboard offset voltage source allows generating offset signals while maintaining optimal utilization of the DAC’s digital range. With the 8MWord of memory, there is lots of room for uploading several different patterns, allowing switching patterns with minimal bus communication.
-
Product
MXG X-Series Microwave Analog Signal Generator, 9 kHz to 40 GHz
N5183B
Signal Generator
Get a fast, compact (2U) alternative to the PSG in the lab, depot or fieldAddress demanding tests of radar modules & systems with near-PSG levels of spectral purityCompensate for system loss & drive high-power amplifiers: +19 dBm output power, -55 dBc harmonics & -68 dBc spurious @ 20 GHzReduce calibration time with switching speed 600 sSimulate narrowband chirps & radar antenna scans with up to five internal function generators that can be used with AM, FM, OM pulse modulation
-
Product
Digital Cable
Digital Cable
The Digital Cable models include a variety of industry-standard front- and back-end connectors, such as 68-pin VHDCI, 68-pin D-SUB, and flying lead options. Some models can connect digital instruments with other accessories to break out cable signals for direct access. Others provide flying leads that plug directly into any 0.1 in. header connector.
-
Product
Ethernet/LXI digitizerNETBOX 8 Bit High Speed Digitizer - 5 GS/s on 4 Channels, 2.5 GS/s on 8 Channels, 1.25 GS/s on 16 Channels
DN6.225-16
Digitizer
The digitizerNETBOX DN6.22x series allows recording of up to 24 channels with sampling rates of up to 5 GS/s and a bandwidth of 1.5 GHz. These Ethernet Remote instruments offer outstanding A/D features both in bandwidth and signal quality. The combination of high sampling rate and resolution makes these digitizers the top-of-the-range for applications that require high speed signal acquisition. The digitizerNETBOX can be installed anywhere in the company LAN and can be remotley controlled from a host PC.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
Digital I/O Module
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
PCI-5421, 100 MS/s, 16-Bit Waveform Generator Device
778692-01
Waveform Generator
The PCI‑5421 can generate user-defined, arbitrary waveforms and standard functions, including sine, square, triangle, and ramp. This arbitrary waveform generator can generate signals from -6 V to +6 V and uses direct digital synthesis (DDS) to precisely generate waveforms. The PCI‑5421 also features advanced synchronization and data streaming capabilities.
-
Product
NI-9411, ±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module
779005-02
Digital Module
±5 V to 24 V, 6 Differential/Single-Ended Channels, 500 ns C Series Digital Module - The NI‑9411 works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and devices. The NI‑9411 is a correlated digital module, so it can perform correlated measurements, triggering, and synchronization when installed in a CompactDAQ chassis.
-
Product
Digital Multimeter, 6 Digit
34465A
Digital Multimeter
Resolutions up to 6 digitsReading rates up to 50,000 readings/sMemory up to 2 million readingsCurrent ranges from 1 A to 10 AUSB and LAN interfaces, optional GPIBBenchVue software enabled: Do more with your PC and instrument together, no programming required. Easily control your DMM, quickly build automated tests, log measurements and save precious time.
-
Product
6GHz RF Analog Signal Generator Module
LS6081D
Signal Generator
The LS6081D, 6GHz Single Channel RF Analog Signal Generator, offers industry leading performance, combined with a compact small footprint form factor. The LS6081D features exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. The LS6081D was designed to offer industry leading price to performance ratio, needed from the R&D benches to the production lines.
-
Product
Digital I/O Board
3512
Digital I/O Module
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
PCIe 8 Bit High Speed Digitizer - 1.25 GS/s on 1 Channel, 500 MHz Bandwidth
M4I.2210-X8
Digitizer
The 9 models of the M4i.22xx-x8 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Waveform Generator, 20 MHz, 2 Channel
EDU33212A
Waveform Generator
The EDU33212A dual channel function / arbitrary waveform generator provides uncompromising performance for dual channel synchronized test output signals.
-
Product
Bi-Directional Differential-TTL I/O PXI Card
GX5641 Series
Digital I/O Module
The GX5641 is a 3U PXI instrument card that can be used for general data acquisition, process control, Automatic Test Equipment (ATE), functional test, and factory automation applications. The GX5641 consists of 64 bi-directional TTL-differential I/O channels. Each channel has two ports (TTL and differential) which can be individually set to operate in either conversion or static I/O modes.
-
Product
PCIe-6535B, 32-Channel, 10 MHz, 40 MB/s Digital I/O Device
782629-01
Digital I/O Module
The PCIe-6535 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
779004-02
Digital Module
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
EMX-75XX
Digital I/O Module
The EMX-75XX Series adds to AMETEK VTI Instruments' growing PXI Express (PXIe) Core Automated Test Equipment (ATE)TM family as a high-current, high-density digital input/output line of modules. Unlike many static I/O PXIe modules on the market today, the EMX-75XX Series can sink or source up to 300 mA on each channel. Delivering beyond just 2 V and 5 V, engineers can program the cards to support a wide range of voltages and more—on every channel, for both input and output.
