Current Generators
Produce electric current.
-
product
2.5G DPSK Demodulator
Optoplex’s Optical DPSK Demodulator, also known as Delay Line Interferometer (DLI), converts phase modulation to amplitude modulation over the entire C+L band in support of data transmission rates of 2.5, 10 or 40 Gb/s. The DPSK demodulator is designed for phase modulated optical communication systems utilized in commercial, defense and space exploration markets. The device plays a key role in improving signal quality and performance to meet the expanding demand for higher data rates and more complex transmission formats within current and next generation systems without major capital expenditure. Optoplex’s DPSK Demodulator is based on a patented free-space optical design, which is compact, athermal and polarization-independent. Themeasured frequency drift over temperature is only ~0.02 GHz/°C for our standard passive device. Further, this DPSK Demodulator exhibits a total polarizationdependent phase shift of less than 2 degrees over the entire operating temperature range with a high extinction ratio. Optoplex’s DPSK Demodulators can be configured to be fully tunable, colorless tunable or purely passive. Dual-Rate DPSK Demodulator is also available.
-
product
Ground-Fault Products for Solidly Grounded Systems
Ground-fault products are used to monitor grounded systems (ungrounded and grounded) for fault currents or residual currents. The sum of all conductors except the protective earth conductor is measured by means of measuring current transformers.In general, ground-fault monitors (RCM - residual current monitors) are used to send a message to the user even before reaching the shutdown threshold of the GFCI. Ground-fault monitors detect deteriorations of the insulation level at an early stage and in a reliable way.
-
product
Dual Surge Current Generator
MIG0624T-K12
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
product
Digital Electrical Network Analyzer
1826 NA
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Earth Resistance without the need for poles in the ground or external measuring wires.● Earth measurement uses the real earth current path and the current generated by the electric network, without the need for any disconnection.● The Earth Resistance displayed is exactly the earth resistance that the earth current will need to go through if an earth fault occurs. No need to add all the bonding points and connection paths resistances.● Displays voltage supply at the transformer (Line to Neutral), without loading the transformer. Displays voltage between Line (Phase) and Earth (Ground), without drawing any current.● Measures the impedance of the line itself so you can analyze and differentiate between the multiples paths of the wiring.● Measures the Neutral Impedance. Single one smart push button operation; ON, Test, Scroll trough results and menus.● Checks wiring integrity (LEDs).● Auto off/auto ranging (software ranging). ● Combined prospective short circuit current, loop, individual wire and Earth Tester.● Voltage test L-N and L-E.● Loop test for L-E and L-N and PSC.● Enables analysis of constituent components in L-E and L-N loops giving resistance of earth, neutral wire, live wire and transformer winding.● Display can be customized for large orders.
-
product
Handheld 2G & 3G Cell Phone Detector
SH-055UMW / 10127
This new portable Mobile Phone Detector is made for detecting 2G & 3G cellular phones (all current generations and all networks) communication in a place.
-
product
PathWave BenchVue Advanced Power Control And Analysis
BV9201B
The BenchVue Advanced power control app helps characterize voltage and current measurements and generate arbitrary waveforms for single instrument support.
-
product
Counter Electrodes
For a system using a three-electrode potentiostat, we measured current when a potential is applied between the working electrode and the reference electrode. Passage of current through an electrical circuit requires electron transfer reaction between the working electrode and the counter electrode.The main function of the counter electrode is to provide the location of the second electron transfer reaction. Important parameter of the counter electrode is the surface area. It is required (area) large enough to support the current generated for the working electrode. For example, the surface area of the platinum electrode of 5 cm is sufficient to use as an electrode, such as steady-state cyclic voltammetry experiments. However, for generating a high current measurements such as bulk electrolysis, the counter electrode of a larger area is required, as Catalog No.012961 which the length of platinum is 23 cm. This electrode is used for measurement, such as rotating ring disk.
-
product
Dual Surge Current Generator
MIG0612T-K12
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
product
Current Generator
MIG12100
MIG12100 is a current generator with wave shape 8/20 ìs. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied. The generator can deliver up to 100kA impulse current supported by 12kV impulse voltage, making it ideal for testing big varistors with high hold-on voltage. Mechanically the MIG12100 consists of two large racks and a separate control console with high voltage output terminals protected by a glass acrylic test cabinet.
-
product
Scatterometers / Thin Film Metrology Systems
OptiPrime Series
The n&k OptiPrime series are automated metrology systems used to fully characterize and monitor Thin Film and OCD applications for both current and next generation IC processes.
-
product
Serial Controller
PMC522/FP
The PMC522/FP provides a uniquely effective solution for integrating serial I/O requirements into a VMEbus or CompactPCI system. Implemented on a single PMC card, the PMC522/FP is fully compatible with the current generation of VMEbus and CPCI single board computers, as well as any special purpose processor that includes a PMC connector.
-
product
Current Tester
MIG0624
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
product
Universal Multichannel System up to 3.5 kV
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 3.5 kV output voltage- Maximum Current 3.5 mA- Either Radiall Multipin or SHV connectors- Available with either positive or negative polarity- Up to 10 nA / 500 pA current set / monitor resolution- Up to 5 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mVpp- 2 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in over current condition- Specific design for High Altitudes 0÷5000 m (A7030 only)
-
product
Wi-Fi Interception System
Wi-Fi networks have become very popular among the current generation as a secure means of communication and browsing. Interception of the Wi-Fi networks can enable the LEAs to collect information with immense intelligence value.
-
product
Through Hole type AC Current Sensor
CT-6K
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
product
Resistivity Meters
SSR-MP-ATS
Integrated Geo Instruments & Services Private Limited
The instrument design incorporates several innovative features and advanced techniques of digital circuitry to make it a reliable Geophysical tool providing high quality data useful for mineral and groundwater exploration and any other Geophysical applications. The SSR-MP-ATS sends the entire current into the ground without wasting power for constant current generation thus increasing the signal strength to probe deeper layers.
-
product
Line-scan Camera
The Avaatech XRF Core Scan can also be equipped with a high-resolution line-scan camera that allows to obtain detailed pictures of the sample material, including color data. The current generation camera is the JAI LT-400 CL-F Color Line Scan Camera.
-
product
Eddy Current Testing
Shanghai Xianda Denshijiki Industry Co.,Ltd
And the eddy current generated on the specimen by the specimen by the action of the magnetic field can not be detected (defect) and the change due to the influence of the material is detected.
-
product
Signal Generators/Calibrators
DC Voltage and Current Signal Generator and Tester for Routine Maintenance of Standard Devices
-
product
Leakage Current Tester
TOS3200
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
product
Pulse Current Generator Multi-Pulse Generator
Shanghai Guantu Technology Co., Ltd.
What is the difference between ordinary current and pulse current?The difference between ordinary current and pulse current: ordinary current is continuous and uninterrupted current.Pulse current is a current whose direction does not change and whose intensity changes periodically with time.
-
product
Current Generator
SL / 650
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable to supply primary current or other single-phase 50Hz power supply equipment when calibrating current transformer.
-
product
DC Bench Power
XPF Series
AMETEK Programmable Power, Inc.
The Sorensen XPF is a new type of bench power supply designed to meet the need for flexibility in the choice of voltage and current. Typically, the maximum voltage and maximum current are not required simultaneously. The PowerFlexTM design enables higher currents to be generated at lower voltages within an overall power limit envelope. This is achieved by using the latest switch-mode technology.
-
product
Multi Circuit DC Current Monitor (16 channels)
MCM-1600PV
MULTI MEASURING INSTRUMENTS Co., Ltd.
Measuring･display of DC current values generated by PV systems and DC load current of related apparatus in multi circuit successively for a long term as well as memorizing the average current values between the intervals, of which data can be transmitted to PC in Excel File.
-
-
product
Process / Voltage / Current
Calibrator high precision process signals able to measure and generate current and voltage.
-
product
Dynamic IR Scene Projectors
Mirage™
In 1999, SBIR introduced MIRAGE™, the world’s first integrated Dynamic IR Scene Projection System, designed to support hardware-in-the-loop testing of missile seekers, FLIRs, counter measure simulation and tracking systems. MIRAGE™ is a complete turnkey infrared scene projector that utilizes unique resistive emitter array technology to produce high definition dynamic IR scenes. The original MIRAGE™-1 used a 512 x 511 pixel resistive array emitter capable of frame rates up to 200 Hz. Below is a list outlining the progression of the product line and a list of SBIR’s currently available scene generation systems:
-
product
Low Voltage Boards
- 6 or 8 independently controllable full floating channelsup to 64 V- Up to 60 W Max channel output power- High resolution on voltage set- Programmable TRIP parameter- Programmable ramp up / down- Current generator operation in overcurrent condition- Overcurrent programmable protections- Individual remote sense lines- Up to 0,2 mV voltage monitor resolution- Up to 1 mA current monitor resolution- Voltage ripple smaller than 3 mVpp
-
product
Portable Sources
While testing of meter installations on-site often a sufficient load is missing to achieve reliable results. You can generate currents up to 120 A and voltages up to 500 V with our sources.
-
product
Universal Multichannel System up to 100V
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 100 V output voltage- Maximum Current: 1mA, 10 mA or 1 mA/100 μA (dual range board)- Individual Enable (A1510 only)- Either DB37, DB25 or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA / 100 pA current set / monitor resolution- Up to 2 / 0.2 mV voltage set / monitor resolution- Extreme Low ripple, down to < 3 mVpp- 3 different channel grounding- Common Ground (AGxxxx)- Common Floating Return (Axxxx)- Full Floating (A1510 only)- Independently programmable for each channel:- Output voltage- Current limit- Ramp up/down- TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A1510)
