Test Leads
Cable hook-up between a test node and test instrument.
See Also: Flying Leads, Multimeters
-
Product
Phase Sequence Indicators (Contact Type)
863 PR
-
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Allows you to check a wide range of 3-phase power sources.● Special test leads length are available on request.
-
Product
Digital (1kV below) Insulation Tester
2801 IN
-
Standard Electric Works Co., Ltd
● Microprocessor-controlled with advanced safety features.● Three test voltages : 250 / 500 / 1000V.● Displays and sound warning if external voltage present.● Ener-Save™ feature to extend battery life.● Continuous battery monitoring.● Auto ranging / auto-null / auto-off.● Insulation tested at 1mA.● Built-in carry case, test leads in separate pouch.● Real-time barg-raph display of test voltage and voltage decay during discharge.● Audible and visual message displayed if external voltage is present.● Large LCD.● Display can be customized for special orders.● Continuity buzzer.● Show test time duration (up to 99.9s) for easy comparison.● BS 16 edition.
-
Product
Low-Voltage Twin-Lead Tester
69134
-
Tests 5-50 volt, AC or DC circuits and components.Built-in lamp glows if circuit is live.Each of the 4-1/2'' (114 mm) test leads has an alligator clip on the end.Handy pocket clip.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
6/12/24/36V Conductance Battery Tester
MBT300
-
Tests 6/12/24V lead acid batteries individually or in parallel and series battery packs. Displays battery or battery pack condition as % available capacity, rated capacity (CCAs), state of charge voltage, and good or replace status. Tests 6/12/24/36V starter and charging systems including starter draw, alternator and regulator output (loaded/unloaded), and diode ripple.
-
Product
Probes & Test Leads
-
The Di-LOG range to test leads are designed and manufactured to the highest quality and meet all safety standard as stipulated in BS EN 61010
-
Product
Test Lead Set
69128
-
Set of two (red, black) 32'' (813 mm) test leads.Each lead has alligator clips attached to both ends.Multi-purpose tooth pattern for better gripping of wires and test points.Recommended for general purpose measurements.
-
Product
CAPACITANCE METER
C350
-
This is a high quality digital capacitance meter. Check the accuracy and status of capacitors up to 20mF, a very handy tool for virtually any technician. It features high accuracy (0.5%) and 9 selectable ranges. A zero adjustment knob is also provided to "zero" test lead capacitance. Includes test probe set and yellow rubber boot.
-
Product
Alternator/Battery Load Tester
6031
-
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
-
Product
Industrial Clamp Meters
-
*Measures AC+DC current*AC and AC+DC voltage measurements with digital low pass filter for accurate readings on variable frequency drives*Also measures DC voltage, resistance, capacitance and frequency*Tests continuity and diodes*Flashlight inside clamp jaw for easier work in dark locations*Backlight & relative mode for added versatility*Peak-RMS measures motor inrush current*AmpTip™ increases accuracy on small wires and low current*Two voltage detection modes - non-contact or using a single test lead*Data hold*Recording of Maximum, Minimum, and Average readings*Crest (peak hold) feature captures current or voltage peaks as short as 5 milliseconds
-
Product
Emissions Dynamometers
MD-100-M-2WD
-
High throughput demands of Centralized Emission Inspection require the use of rugged and durable emission inspection equipment. Designed from inception to withstand punishing use and misuse, Mustang Dynamometer has set the performance standards of equipment manufactured and used worldwide for centralized emissions testing. Our pioneering experience has led us to be the world leader in the design and manufacturing of rugged inspection and maintenance hardware and software for the I/M industry. We have centralized testing lanes installed all over the world in climates from cold to hot and from wet to dry. By the end of 2020 we estimate that our equipment will have performed nearly 1.5 billion vehicle tests. Continuous improvement leads us to innovative solutions based on our knowledge of design, service, maintenance, ergonomics and overall functional capabilities. Mustang I/M Centralized Emission Inspection equipment is designed for our customer’s demands.
-
Product
Closed-Link Field Test Kit
630
-
TESCO’s Closed-Link Field Test Kit (Catalog No. 630) with Power Factor has been designed to reduce the weight of field test equipment to the lowest possible limit when testing electric meters without potential links or with the links closed. The unit is protected within its ergonomic carrying case by a durable powder coated aluminum shell. The total weight of the meter test kit including leads, and digital reference standard is only 30 lbs! The test kit carrying case also incorporates ample storage space for the cable set and other tools.
-
Product
Multi-Volt Twin-Lead Tester
69135
-
Checks and indicates voltage on circuits up to 460 volts, AC or DC.Tests for DC polarity, frequency, and polyphase line.Four separate bright neon AC/DC indicators indicate voltage being tested 110, 220, 277 or 460 volts.Reinforced test leads, stored in the case, and furnished with probes on the ends.Reinforced casing.
-
Product
Power Transformer Automatic Test Device
XD71
-
Hangzhou Xihu Electronic Institute
The device is used for power transformer power outage routine test items to do automated testing.Which is characterized by dielectric loss, insulation resistance, DC resistance, tap-changer switching characteristics, short circuit impedance and variable ratio of six test items are concentrated in an instrument,so that the instrument function, test power and test lead height fusion.Field test, just start wiring once, at the end of unplugging wiring once,the middle process by the test personnel in the computer terminal to send command control,the test system automatically completes all or part of the above test items.
-
Product
USB Tester 2.0
TLS-0050
-
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
Product
Continuity Testers
-
The extremely versatile continuity tester offers an insulated, shock-resistant and break-proof plastic housing. The pluggable and screwable connection between the test leads and the terminal post is safe to touch. The continuity test is indicated by an acoustical and an optical signal. The integrated torch light allows you to find wires quick and safe under though circumstances.
-
Product
Low Ohms VOM
260-6XLM
-
Designed for the special needs of solid-state circuitry measurements, the 260-6XLM has extra low power ohms ranges. It also offers all of the advantages of the standard 260 family, including a resettable overload protection circuit on the 260-6XLPM. Both versions come with batteries, manual and test leads with alligator clips.
-
Product
Low Noise Test Leads For N1413 With B2980 Series, 3m
N1425B
Coaxial Cable
The N1425B is designed to operate specifically with the B2985B/87B. It can hold DUTs with large terminals being used with the N1426C. The N1426A with the N1425B is available for measurements of small DUTs such as PC boards or IC sockets. The N1426B with the N1425B enables the construction of simple custom-made test leads. The N1413A High Resistance Meter Fixture Adapter is also required to connect the N1425B to the B2985B/87B.
-
Product
PRO Test Lead Kit
142
-
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
Product
Testing & Measurement Services
-
Delserro Engineering Solutions
Delserro Engineering Solutions is your complete source forHALT/HASS, Accelerated Life Testing, Environmental Testing, Lead Free Solder Joint Reliability Testing, Linear andNon-Linear FEA, Computational Fluid Dynamics (CFD)
-
Product
Earth Ground Test Lead Kit
TL-796
-
*Earth Resistance Test Lead Kit*For use with IDEAL 61-796 3-Pole Ground Resistance Tester
-
Product
Engine Test
-
The engine test bench is a facility used by engine manufacturing plants to validate internal combustion engines before fitting to the vehicle. OEMs perform ‘Hot’ or ‘Cold’ testing operations in order to measure several physical variables and to diagnose any failure of parts or components. Jackmark Engineering provides bespoke rugged electrical test connection leads suitable for the industrial environment of petrol or diesel engine testing.
-
Product
VXI
-
VXI stands for VME eXtensions for Instrumentation. It is an open standard first developed by five leading Test and Measurement companies in 1987 to standardise a backplane capable of developing open, interchangeable instrument modules that could be used to build Automatic Test Equipment (ATE).Data Patterns designs and markets a wide range of VXI modules, some of which are listed below. Due to the use of the latest technologies, Data Patterns VXI modules offer the highest I/O density available in the industry today.Further enhancements of functional capabilities are achieved by the use of VXI IP carriers and VXI M Module carriers. This extends standard functions available from Data Patterns in these mezzanine architectures to the VXI platform.
-
Product
Digital Mini Multimeter
501
-
This is an economical digital multimeter that can’t be beat. The #501 has the capabilities of full range units but is small enough to fit in your pocket. Its low price will surprise you! Includes test leads, protective holster, instructions and installed battery.
-
Product
Deluxe Relay Test Set
60660
-
Jumpers have tabs for clamping and flat pads to place test leads on. No need to pierce wires or connect multiple jumper wires. Also Includes Test Lead Kit for easily and securely connecting Relay Test Jumpers to a multimeter. Jumper wire may be used between common and open to close the relay circuit for testing and has a test port to easily check voltage. Also provides access for a clamp-on amp meter. Relay Puller Pliers easily remove electrical relays without damage to the relay or electrical box.
-
Product
80-500V AC/DC Twin-Lead Circuit Tester
1927
-
Peaceful Thriving Enterprise Co Ltd
*Handy pocket-clip.*Bright neon indicator.*With UL and cUL Approval.*Insulated housing and test leads.*Check voltage on 80-500V AC/DC.*Built-in lamp will glow if circuit is live.
-
Product
Analogue (1kV below) Insulation Tester
4132 IN
-
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
Product
1Gsps, 18 Channel, Logic Analyzer with Protocol Analyzer plugins and Hardware Compression
DigiView™ DV518
-
- Physical Channels: 18- Sample rate: 4ch@1 Gsps or 9ch@500Msps or 18ch@1Gsps (4 ch. are sampled every 1ns or 9 ch. are sampled every 2ns or 18 ch. are sammpled every 4ns)- Typical capture: 100M transitions (> 1B samples)- Hardware based triggers with 8 universal match circuits, and partitionable 16 stage sequencer- Adjustable Threshold (± 4V)- Real-time, Hardware-based, Adaptive Compression- Channels protected to ± 20V- Ground leads protected to ± 12V- High-quality test leads: 66 strand soft copper wires, flexible insulation, and gold plated connectors. Fit .025 square posts as well as the included clips.- Extra ESD protection- Streaming storage with auto fall-back to Store & Forward mode ensures large storage and reliability.- USB 3.0 (SS) or USB 2.0 (High Speed)- USB powered- Each DigiVIew includes all avialable Protocol Analyzer plugins (including: I2C, SPI, CAN, Async, Sync, 1-wire, I2S, TDM)- Free Plugin Developers' Kit- Requires Windows 7 or greater OS (32bit or 64bit)- Free Lifetime sofware updates.- 1 year warranty
-
Product
Micro-Ohmmeters
RMO-A Series
-
The RMO-A is a portable micro-ohmmeter designed for contact resistance measurements of switchgear during manufacturing, commissioning and maintenance stages. This micro-ohmmeter is widely used by medium and high-voltage circuit breakers manufacturers. Other typical applications are testing of disconnecting switches, high-current bus bar joints, cable splices, and different high-current links. It accurately measures not only in factory environments but also in high-induction fields and substationsThe RMO-A series contains 6 models, rated from 100 A (RMO100A) to 600 A (RMO600A). The RMO500A (formerly CPM500) is our best seller, with 500 A ripple-free current and weighs only 8 kg.Although placed in a very portable and lightweight metal housing, RMO-A micro-ohmmeters have very high output power capabilities. They can generate 600 A test current continuously for up to 20 s. You can test with current up to 100 A without rest time. High output voltage enables a wider measurement range at the highest test currents, as well as the use of thinner/longer test cables. For testing with 100 A, 20 m test leads can be provided with only 16 mm2 cross-section.RMO-A micro-ohmmeter generates a true DC ripple-free (less than 1 %) current with automatically regulated test ramps. During a test, the RMO-A ramps up with increasing current before measuring and decreasing current after the measurement. This significantly decreases magnetic transients and ensures great accuracy.An additional option is a built-in High Precision module suitable for measurement of very low resistances, ranges from 1 to 30 µΩ, with 0,01 µΩ resolution.These instruments can store up to 500 measurements in internal memory. A built-in thermal printer is available as an option.Our free DV Win software communicates with the RMO-A micro-ohmmeters via USB or RS232 interface. It allows you to run the test remotely from PC, as well as to download test results, analyze and generate fully configurable test reports.
