Manipulators
1) hold test heads for docking. 2) hold probes for positioning.
-
Product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
CAN Interface
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
Product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Fiber-coupled Polarimeter
-
The new AP6051A stand-alone benchtop fiber-coupled polarimeter enables real time monitoring of the SOP, DOP, and power of a light signal in fiber. It can display SOP data information either on a Poincaré sphere, a Jones diagram or on a virtual oscilloscope. Covering the operating wavelength range from 1520 to 1610nm, it offers excellent performance, fast sampling rate, high SOP accuracy, and wide dynamic input optical power range. Optionally, it can be used in combination with an internal Optical Filter to measure the SOP as a function of frequency. Intuitive software and touch screen allows an easy manipulation of the device.
-
Product
NI-9861, 1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module
781962-01
CAN Interface
1-Port, Low-Speed/Fault Tolerant C Series CAN Interface Module—The NI‑9861 is a fault-tolerant Controller Area Network (CAN) interface for developing applications with the NI‑XNET driver. The NI‑9861 is ideal for applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other data acquisition measurements in the same NI CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same NI CompactRIO chassis.
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
Test Platform
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
Ultra High Performance 3D CT System
UltraTom
-
3D micro-tomography (CT Scan) and nano-tomography. Modular system with multiple imagers and x-ray generators. Experimentations possible in-situ. Large volume Inspection and manipulation volume.
-
Product
Measuring Light Curtains
-
Leuze electronic GmbH + Co. KG
These devices are perfect for measuring moving objects as they pass by. The measurement results can be output via the fully integrated interface. At the same time, the programmable switching outputs allow downstream elements to be manipulated. Likewise, multiple light curtains can be cascaded. The nearly unlimited possibilities for configuring multiple measurement areas and evaluation functions make the devices problem solvers for a variety of measurement tasks. The range of available resolutions and measurement field lengths ensures optimum adaptation to your application.
-
Product
3D Software
Geomagic Wrap
-
Geomagic Wrap 2017 delivers a new and improved 3D scan-to-model workflow. From expanded file format support to manipulating texture maps for bringing your printed parts to life, the 3D scan data toolbox of Geomagic Wrap provides a wealth of possibilities.
-
Product
DR software, for use with CT100 Series TDRs
CT Viewer™
-
CT Viewer™ is a full-featured TDR waveform analysis software package for Microsoft® Windows® XP / Vista PCs that lets you archive, manipulate, analyze, and compare TDR data acquired with CT100 Series Automated Metallic TDRs or any other TDR instrument, now with live internet streaming and remote control of CT100 Series TDRs. CT Viewer™ is included with CT100 Series TDRs. Read on to discover how CT Viewer™ will change the way you test cables.
-
Product
Curve Tracer
Series 5000C
-
Our curve tracers are used worldwide for high volume production, quality control and final testing of descrete semiconductor devices. Provided with an Intel based single board computer(SBC) and Windows based software, the Scientific Test curve tracer is highly reliable, extemely fast, very easy to operate, and provides quick creation of digital curves for data storage and intuitive manipulation.
-
Product
MANIFULATOR
-
As one of the most important module in Probe_Station, manipulator is an accurate system that probe micro distance() and contact on the electrode of semiconductor wafer, device. ECOPIA's Manipulator is very easy to use and probe arm's elastic plate is good to protect sample's surface, from being damaged by Z direction movement.
-
Product
Eyepiece-less Stereo Microscopes
-
Vision Engineering’s eyepiece-less stereo microscopes are better for users and for business. Their ergonomic design lets the operator sit back in a comfortable position, and the expanded pupil technology delivers an enhanced 3D view of the subject. The relaxed natural posture makes it easy and to work with tools and to manipulate the subject. Greater comfort and ease of use directly translate into greater productivity and quality.
-
Product
LIN Interface Module
C Series LIN
LIN Interface
C Series LIN Interface Modules are bus interfaces for developing applications with the NI-XNET driver. The NI-XNET device-driven DMA engine couples the LIN bus to host memory to minimize message latency. You can import, edit, and use signals from LDF databases in integrated LIN databases. C Series LIN Interface Modules work well for applications requiring real-time, high-speed manipulation of many LIN frames and signals, such as hardware-in-the-loop simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
LIN Interface
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
Product
The Nanomotor®
-
The patented Nanomotor® is a piezo driven linear motor. It is a multifunctional basic part for many positioning and manipulation devices. It has a positioning stroke of up to more than a centimeter while operating with atomic resolution. The Nanomotor thus bridges eight orders of magnitude. The Nanomotor consists of a cylindrical housing and a slider with a free axial hole inside. It combines high resolution in the sub-nanometer range with a large positioning stroke. The Nanomotor utilizes a piezo tube for fine positioning and a shock wave produced by the same piezo tube for coarse movements. The small Nanomotor is half the size of a match stick. It can lift six times its own mass. Every point of its stroke can be reached with a speed of up to 1 mm/s. The Nanomotor also works in ultrahigh vacuum or even under water. It is driven by a PC card at a supply voltage of only ±15 volts.
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
ActiveX Controls for ADLINK DAQ/DAQe/PXI-2000 Series Cards (Vista Ready)
D2K-OCX
-
D2K-OCX ActiveX controls communicate with ADLINK data acquisition cards to perform digital, analog, and timer/counter operations. These ActiveX controls well-designed to hide all details of hardware manipulation so the data acquisition operations can be achieved by only few lines of codes. Furthermore, any hardware configuration can be done with the easy-to-use property pages, and the acquired data is returned in a event-driven manner.
-
Product
Probe System for Life
PS4L
-
The Probe System for Life, or PS4L, is SemiProbe’s patented adaptive probe system architecture. Unlike traditional probe systems, all of the basics components of our systems, including the bases, stages, chucks, microscope mounts, and manipulators, are interchangeable, upgrade-able, and configurable. The PS4L Adaptive Architecture ensures and optimal test configuration for each individual customer application.
-
Product
Emission software
EMiScan
-
This Windows Emission package is an ideal debug / development tool providing easy of use with a flexible approach so you can quickly capture and manipulate data
-
Product
Ophthalmic Surgery Microscopy Solutions
-
Ophthalmic surgery requires a high degree of precision to ensure optimal accuracy when maneuvering instruments and manipulating delicate ocular tissue. The surgical microscope is one the most important instruments in eye surgery, allowing ophthalmic surgeons to visualize micro-anatomical details and perform efficient and extremely precise movements.
-
Product
NI-9853, 2-Port, High-Speed C Series CAN Interface Module
779429-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
RF Signal Generators
RF Signal Generator
RF Signal Conditioning provides signal manipulation capabilities for high-frequency or broadband signals. You can use these products to augment the capabilities of connected instruments to improve attributes like accuracy and frequency range.
-
Product
Universal Manipulator
LS
-
Manage the rapidly changing production environment and achieve the lowest cost of test, converting between probe, final, engineering and service positions with ease. Rapid advancements in semiconductor test technology have resulted in highly efficient test cells, capable of device test throughputs far greater than ever before.
-
Product
PCI-8511, 1‑Port, Low‑Speed/Fault-Tolerant CAN Interface Device
780682-01
CAN Interface
1‑ or 2-Port, Low‑Speed/Fault-Tolerant CAN Interface Device—The PCI‑8511 is a fault-tolerant controller area network (CAN) interface for developing applications with the NI‑XNET driver. The PCI‑8511 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
3-DOF Simulation Table
KRD60 series
-
KRD60 Series 3 DOF simulation table simulates various mechanical, electrical, and electronic products installed on ships, seaplanes, and other equipment to perform sway and tilt tests to determine the ability and structural integrity of the product to withstand severe sway and tilt requirements. The tilt test is mainly applicable to large-angle tilt caused by ship damage, manipulation, imbalance in loading and unloading, and wind. The sway test is mainly applicable to long-term swaying of the ship due to external forces such as wind and waves, which must be maintained normally or products that work reliably, and products that have a significant impact on their performance in a rocking environment.
-
Product
Audio Fiber Tracer
CFT-810
-
Motorized Polarization Controller. In addition to its basic function of adjusting polarization states in multi channels, it also provides convenient ‘save and recall’ functions. As a Scanning PC, it provides very powerful ‘auto scan’ modes with variable scanning speeds. Polarization states can be manipulated by either manual adjustment or remote control (GPIB, RS-232) using two quarter-wave plates in each channel of the PC1600. Additionally, the auto scan mode of FIBERPRO’s Motorized Polarization Controller has been upgraded in LPC, and it shows another auto scan mode of four quarter-waveplates with higher polarization extinction ratio when connecting two channels at a high speed. PC1600 is an essential tool to complete fiber-optic, multi-channel measurement systems such as WDM/DWDM as well as R&D (i.e. PMD experiments), and manufacturing.
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Handover Emulator
-
Qosmotec Software Solutions GmbH
The Qosmotec handover test system QPER is a versatile test platform for emulating the RF signal between radio devices in a wireless network, e.g., between mobile stations and radio infrastructure of a mobile network. It is employed in test beds where radio signals are transmitted through coaxial cables and specifically manipulated by testers. QPER can be based on various hardware platforms, from attenuator arrays to digital channel emulators.
-
Product
Manipulators
-
The patented Nanomotor is the heart of any manipulator. Three independent linear stages are used in every single manipulator. The manipulator provides 0.5 nm resolution in all three axis. All manipulators can be used in air setups or inside of electron microscopes. Docking stations allow an easy transport between any setup.
-
Product
SpaceWire Physical Layer Tester
141
-
The SpaceWire Physical Layer Tester (SPLT) is a tool designed to test, validate and verify a SpaceWire system across all levels of the SpaceWire standard. Two SpaceWire ports employ a special LVDS interface which allows the transmitted signals to be deliberately and measurably manipulated to test the capability of a unit under test to receive signals of varying quality.
