Breadboards
Board filled with electrical sockets for quick and replaceable component connections. Facilitates quick prototyping of electrical circuits.
-
product
SparkFun High Precision Temperature Sensor
TMP117 (Qwiic)
The SparkFun Qwiic TMP117 breakout is a high precision temperature sensor equipped with an I2C interface. It outputs temperature readings with high precision of ±0.1°C across the temperature range of -20°C to +50°Cs with no calibration and a maximum range from -55°C to 150°C. The SparkFun High Precision Temperature Sensor also has a very low power consumption rate which minimizes the impact of self-heating on measurement accuracy. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Probe Systems
Mini-PS4L
The mini-PS4L series of probe systems are built using a similar concept as our patented Probe System for Life (PS4L) Architecture. The base system is built on a 300 mm x 300 mm metric breadboard and that allows the user to configure the system to meet the application and budget.
-
product
SparkFun Solder-able Breadboard
Large
This is the Large SparkFun Solder-able Breadboard. A bare PCB that is the exact size as our full-size breadboard with the same connections to pins and power rails. This board is especially useful for preserving a prototype or experiment you just created on a solderless breadboard by soldering all the pieces in place.
-
product
PXI Breadboard Module, 2-Slot, 25-Pin D-Type
40-220A-302
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
PXI Prototyping Module, 2-Slot, 78-Pin D-Type
40-225A-402
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
SparkFun GPS Breakout
NEO-M9N, U.FL (Qwiic)
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
SparkFun Human Presence Sensor Breakout
AK9753 (Qwiic)
This is not your normal Passive Infrared (PIR) sensor! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic-enabled, 4-channel Nondispersive Infrared (NDIR) sensor. Each channel has a different field of view, so not only can the AK9753 detect a human, but it can also tell which direction the person is moving. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
SparkFun Photodetector Breakout
MAX30101 (Qwiic)
The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light that is reflected back from the LEDs. This is useful for various applications like particle (i.e. smoke) detection, proximity measurements, and even photoplethysmography. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
PXI Breadboard Module, 1Slot, Dual 20-Pin GMCT
40-220A-811
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Tiny AVR Programmer
The ATtiny45 and 85 are a couple of really cool little MCUs but did you know you can program them in Arduino? That's right, now you can shrink your Arduino projects down to "tiny size" by moving your code straight over to these small but capable ICs. The standard method for programming the ATtiny ICs involves a breadboard, lots of jumper wires and a hardware programmer, but David Mellis over at MIT Media Lab has simplified the process by laying out this handy USB programmer.
-
product
SparkFun Atmospheric Sensor Breakout
BME280 (Qwiic)
The SparkFun BME280 Atmospheric Sensor Breakout is an easy way to measure barometric pressure, humidity, and temperature readings, all without taking up too much space. Basically, you can find out anything you need to know about atmospheric conditions from this tiny breakout. The BME280 Breakout has been designed to be used in indoor/outdoor navigation, weather forecasting, home automation, and even personal health and wellness monitoring. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Capacitors - Binary Chip
Macom Technology Solutions Holdings Inc.
MACOM’s BOO and BSP Series Capacitors are designed to facilitate bread-boarding or to use where a trimming capability is required. These devices feature the same dielectric layer and bonding surfaces as our 9000 and 9100 Series chip capacitors. By connecting the pads in parallel, the capacitance values are additive, so many combinations are possible.
-
product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
PXI Breadboard Module
40-220-001
These breadboard modules allow the user to construct their own circuits in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis.
-
product
PXI Prototyping Module, 1-Slot, 50-Pin D-Type
40-225A-501
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts And Round Posts (610138200 And 610138117)
510150135
QuadraPaddle modules are molded on .1” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .1” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Fully Loaded With Twin Female Contacts (610138200)
510150131
QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. Allowing flexible configuration options with standard commercial connectors, QuadraPaddle modules are designed to fit any VPC pin and socket-based mass interconnect system. Available in 192 and 480 contact positions, QuadraPaddle modules accept standard .100” (2.54mm) pitch headers, breadboards, and connectors for direct PCB, ribbon cable, and other connections as well as discrete wiring.
-
product
SparkFun Breadboard Power Supply 5V/3.3V
Here is a very simple breadboard power supply kit that takes power from a DC wall wart and outputs a selectable 5V or 3.3V regulated voltage. The .1" headers are mounted on the bottom of the PCB for simple insertion into a breadboard. Pins labeled VCC and GND plug directly into the power lines. The lone pair of pins have no electrical connection but help support the PCB.
-
product
Infrared T1 3/4 LED
350-00003
T1 3/4 Infrared light emitting diode, for breadboard or through-hole projects. Used with the LED Standoff and LED Light Shield to build the IR Transmitter Assembly (#350-00017). Frequently used with the IR Receiver for object detection and autonomous robot navigation, this is a compatible replacement wherever an Infrared LED is found in any of our Education Kits Components Listings.
-
product
PXI Breadboard Module 2-Slot, Dual 20-Pin GMCT
40-220A-812
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis.
-
product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
PXI Prototyping Module, 1-Slot no Connector
40-225A-001
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
PXI Breadboard Module, 2-Slot, 78-Pin D-Type
40-220A-402
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
LSM6DSL Click
64207
Parallax speeds the process of Propeller 2 development through our partnership with MikroE, who has created a family of 850+ Clicks for most I/O functions you may envision. For each of the Click boards stocked by Parallax, you will find a documented Spin 2 code example on our Propeller GitHub Object Exchange. Connect your Click boards to the Propeller 2 Evaluation Board or P2-EC Edge Breakout Breadboard using the #64008 P2 to MikroBus Click Adapter.
-
product
Surface Mount-to-DIP JEDEC SOT-25, SOT-23A-6 Adaptor
1110748
Surface Mount to DIP Adapter for SOT-25, SOT-23A-6. Allows for breadboarding or substitution of microgate SOT-23A-6 and SOT-25 IC and transistor packages into .100 [2.54] pitch proto boards or PC boards. Solder masked top-side pads allow user to hand solder devices directly to topside of adapter with fewer problems of solder bridging. Longer male bottom pins are available at special request for easy use of probe clips. Large topside pads allow for soldering test pins, jumpers, etc. to top of adapter.
-
product
PXI Prototyping Module, 2-Slot, Dual 20-Pin GMCT
40-225A-802
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
product
SCB-68A, Noise Rejecting, Shielded I/O Connector Block
782536-01
68-Pin Female Screw Terminal to 68-Pin Female D-SUB, DIN-Rail, Shielded I/O Connector Terminal Block - The SCB-68A provides a shielded I/O connection for interfacing I/O signals to plug-in data acquisition devices with 68-pin connectors. This Terminal Block combines with shield cables to provide low-noise signal termination. The SCB-68A incorporates a completely redesigned mechanical enclosure with a magnetic removable lid, DIN-rail mount compatibility, and a resettable fuse. It is compatible with single- and dual-connector Multifunction I/O with 68-pin connectors. The SCB-68A also includes two general-purpose breadboard areas and an onboard cold-junction compensation sensor.
-
product
SparkFun GPS Breakout
NEO-M9N, SMA (Qwiic)
The SparkFun NEO-M9N GPS Breakout is a high quality GPS board with equally impressive configuration options including SMA. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations with ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions increasing, precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which makes it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
SparkFun GPS Breakout
ZOE-M8Q (Qwiic)
The SparkFun ZOE-M8Q GPS Breakout is a high accuracy, miniaturized, GPS board that is perfect for applications that don't possess a lot of space. The on-board ZOE-M8Q is a 72-channel GNSS receiver, meaning it can receive signals from the GPS, GLONASS, BeiDou, and Galileo constellations. This increases precision and decreases lock time and thanks to the onboard rechargable battery you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
PXI Prototyping Module, 2-Slot, 9-Pin D-Type
40-225A-702
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
