Standards
A controlled reference or acknowledged technical criterion.
See Also: IEC, IEEE, Mil, Interoperability Test, Compliance
-
product
Calibrators
Handheld calibrator is an exceptional instrument performing precision measurement of pressure, temperature, current or voltage. The base unit includes application-specific firmware for convenient instrument calibration and logging of associated data. In addition, the ATE-2 has the ability to interface the system with a computer, data acquisition system or dumb terminal via the standard USB interface.
-
product
PCI Express Mini Card
mPCIe-UCAN2 & mPCIe-UCAN2-ISO
The mPCIe-UCAN2 card features two CAN ports that instantly install in most any operating system as standard COM/ttyS devices. Each port supports CAN2.0 A/B and FD operations including data rates up to 10Mbps and timestamps with 1μs (or 1ms) resolution. These CAN ports can be controlled using a simple ASCII command/response interface using a superset of the popular CAN232 standard (extendedto support CAN FD requirements)
-
product
PXIe-8431/16, 16-Port, RS485/RS422 PXI Serial Interface Module
781473-02
The PXIe‑8431/16 is a high-performance interface for high-speed communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
product
Flexible Multisensor Probes
IT Series
Physitemp multisensors are made with our specially manufactured thermocouple wire. We test and grade this wire to standards better than the accepted ''Special Limits of Error'' and guarantee 0.1°C accuracy in the range of 0-50°C . All multisensor probes conform to NIST standards. These multisensor probes are custom-made and should be ordered to your requirements on number of sensors and spacing between sensors.
-
product
2-Phase Stepper Drives Based On EtherCAT Field Bus
Nu-Step DA Series
The ADLINK Nu-Step DA Series is a stepper driver based on the EtherCAT bus featuring a 32-bit ARM processor and advanced variable current and frequency conversion technology. The driver generates less heat and motor vibration for more stable operation. It not only supports the standard EtherCAT specification, but also supports table comparison triggers for automated optical inspection (AOI) and linear comparison triggers for line scanning.
-
product
Custom Wiring Harnesses and Cables
From flight critical aerospace wiring harnesses to discrete wire assemblies, WinSoft can meet your toughest requirements. Each of our finished cable assemblies and wire harnesses is built to the customer exact specifications and is 100% quality tested. Cable and harness assemblies are certified to meet all customer requirements and applicable industry standards while manufactured to strict ISO processes and procedures.
-
product
Standard 1.08 (31.00) - 3.50 (99.00) General Purpose Probe
EPA-2B40
Current Rating (Amps): 5Average Probe Resistance (mOhm): 35Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 160Full Travel (mm): 4.06Recommended Travel (mil): 107Recommended Travel (mm): 2.72Mechanical Life (no of cyles): 2,000,000Overall Length (mil): 970Overall Length (mm): 24.64
-
product
AC Current Shunts
CSA Series
Ohm-Labs’ CSA series of ac current shunts are designed as laboratory standards for ac current measurement up to high frequencies.
-
product
Modulator
SFT3301
Hangzhou Softel Optic Co., Ltd.
SFT3301 QAM modulator is a high performance modulator developed according to DVB-C (EN300429) standard which is the standard of the European broadband satellite telecommunication. It provides a more powerful receiving ability of various TS come from encoder, multiplexer, DVB gateway, scrambler and video server. In addition, the modulator also has the function of outputting RF, and simultaneously disposes the TS by RS encoding, convolution interlacing and QAM modulating. This device supports local and remote control through NMS software. For the field scope, it can be used for Broadcasting, Interactive Services, News Gathering and other Broadband satellite applications.
-
product
Electric Insulating Oil Tester
PortaTest
Portatesters are easy to use. Based on the test standard, you select the corresponding test sequence. Then, the required test probe and the electrode gap for the selected test standard is displayed. The setting gauge, included in the scope of delivery, facilitates the adjustment of the electrode gap. Afterwards you fill the insulating oil in the test vessel and close the test chamber.
-
product
4U Rackmount Chassis
AX6145
The AX6145 is a 4U-high rackmount industrial computer chassis which supports ATX Motherboard form factor. Two 8cm ball-bearing cooling fan maintains positive air circulation through the whole chassis. The front access I/O ports and drive bays are designed for ease access and maintenance. A wide range of standard computing peripherals can be integrated with the chassis to meet different application requirements.
-
product
3D Audio Servers
GoldSeries
AuSIM offers a growing number of prepackaged configurations, designed to meet a broad spectrum of R&D and deployment needs. These standard packages are generically called GoldSeries, and have a range of options to tune them to the needs of a specific project. If none of these are appropriate to your application, AuSIM will gladly develop a custom package for your specialized needs.
-
product
Plug-In Temperature Transmitter
HR6200
HighReach Measuring & Controlling System Co.,Ltd
The HR6200 input-type integrated temperature transmitter uses an imported temperature sensor and output RS485 standard signals or 4 to 20 mA standard signals through a built-in microprocessor. The product uses a 316L stainless steel casing, and the temperature probe is placed at The front end, which can be customized according to the requirements of the user.
-
product
Functional Testing for Developers
TestLeft
TestLeft is a powerful yet lean functional testing tool for dev-testers working in Agile teams. It fully embeds into standard development IDEs. A built-in access to object and method library is also available with TestLeft. Dev-testers can thereby easily and quickly create robust functional automated tests without leaving their favorite IDEs such as Visual Studio. It also works well with other tools in dev eco-systems such as source control or continuous integration systems.
-
product
Benchtops
Lightel's benchtop scopes use a USB connection to Windows®-based PCs and tablets to view and save clear detailed images of connector endfaces. Our benchtops provide cost effective innovative solutions for inspecting connectors where standard Fields of View may not be adequate. Each benchtop scope comes with easy to use software designed to take best advantage of that scope's capabilities.
-
product
Epstein Tester
VET-1608
VEER make Digital Epstein Tester VET-1608 is complete stand alone instrument to measure AC magnetic properties of electrical steel of all grade and gauges mostly. It refers ASTM-343 standard. It also refers IEC 60404-2 & IS:649. Epstein Frame method is standard & worldwide accepted method to test important magnetic parameters like Watt/kg, VA/kg, Magnetizing Force, Permeability, Form Factor etc on different induction.
-
product
Linear Power Supplies Precision, GPIB or Local Control, Ultra Low Ripple/Noise
Series ATE-DMG
Kepco's 1000 watt instrument-grade digital power supplies, Series ATE-DMG, are linear low-noise power supplies designed to respond very quickly and precisely to voltage and current setting instructions delivered interactively by the GPIB (IEEE 488.2) or from a front panel keypad. When programmed from the bus, the ATE-DMG power supplies respond to the SCPI (Standard Commands for Programmable Instruments) common language for instruments used in an automatic test system.
-
product
Insulated Torque Wrenches
Intended for low and high voltage applications where torque is critical, Mountz insulated torque wrenches protect their operators in both low and high voltage situations. Essential for worker safety, insulated torque wrenches also improve work quality and productivity by preventing product damage due to arcing or shorting. Applications for linemen and electricians include a wide variety of live electrical situations, such as uninterrupted power supply repair. Mountz insulated torque wrenches meet IEC 6900 standards, keeping your workers safe.
-
product
High Current Discharge Testing System
DTV
Cold Crank Testing to industry standards: IEC, SAE, BCIDischarge capacity performance testing to thousands of amperes
-
product
Airframe Mounted Gearboxes (AMAD)
Airframe mounted accessory drives (AMADs) — Every TRIUMPH Geared Solutions accessory drive is built to the highest standards of precision and reliability. The AMAD provides power for the aircraft’s hydraulic pumps, auxiliary fuel pumps and electrical generators. It also provides engine starting capability by transmitting power from auxiliary power units. Our AMADs incorporate carburized and ground gearing and, if the specification requires, AGMA Class 14 standards. Each drive is designed for high power density to minimize weight. Special features such as self-pressurizing lubrication systems assure proper operation at all altitudes within a given flight envelope. The AMADs also contain a disconnect feature which allows ground crews to disconnect the unit for maintenance and performance of electronic and hydraulic systems checks without the engine running.
-
product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
product
Grid Simulators
A grid simulator can be used to simulate the characteristics of low-voltage mains. For this purpose, all voltages and frequencies of the supply networks occurring worldwide can be simulated. Critical states such as short-term voltage dips or voltage peaks (surge/burst) can also be generated.The integrated sequencer function enables the generation of different network parameters, e.g. distorted waveforms and intermediate oscillations. Therefore, grid simulators are well suited for testing conformity to standards and especially for determining the behaviour of electrical equipment in borderline situations. Many European and other international standards are pre-programmed for testing.
-
product
Standard Voltage 37 Pin D-Type Connectors for Pickering
The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.
-
product
Standard Signal Loop-Powered
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and 1: 1 transmission of 0/4 ... 20 mA current signals without additional auxiliary power. Also for use in hazardous areas. Particularly high reliability and certified functional safety up to SIL 3 / PLe.
-
product
Standard 0.39 (11.00) - 1.39 (39.00) Replaceable General Purpose Probe
MEP-30B
Current Rating (Amps): 2Average Probe Resistance (mOhm): 50Test Center (mil): 30Test Center (mm): 0.76Full Travel (mil): 75Full Travel (mm): 1.91Recommended Travel (mil): 50Recommended Travel (mm): 1.27Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 690Overall Length (mm): 17.53
-
product
Bench Multimeters
Fluke Calibration meters have the precision and versatility to handle the most demanding measurements, on the bench or in a system. These instruments are easy to use and offer excellent value that makes them an ideal solution for many applications. Standards laboratory meters include: Reference multimeters; precision digital multimeters; bench multimeters
-
product
Standard 3.27 (93.00) - 8.13 (231.00) High Frequency Probe
K-50L-QG
Bandwidth @ -1dB (GHz): 4.00Return Loss @ -20dB (GHz): 0.80Nominal Impedance (Ohms): 50Test Center (mil): 550Test Center (mm): 13.97Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 225Recommended Travel (mm): 5.72Overall Length (mil): 1,830Overall Length (mm): 46.48
-
product
Socket Accessories (Thru-Hole Options)
The male pin adapter consists of standard high temperature FR4 with pressed in terminal pins and threaded inserts for mounting the socket. The top side of adapter has gold plated pads to receive socket interconnect and the bottom side has 0.006″ to 0.018″ diameter pin tails. These pins can be soldered to the plated thru holes in the target board. Then socket can be mounted to the threaded insert.
-
product
Testing and Assessment Services for Unmanned Aerial Vehicles
Unmanned aerial vehicles (UAVs), more commonly known as drones, have many applications. UAVs can be used in agriculture for crop spraying, movie making and aerial photography, disaster relief, and can even imitate flying animals for conservation or research purposes. Our services can help you make sure your UAVs meet international norms and standards. We test materials and resilience, confirming that your drones do not pose a threat to human health or the environment. Our services can help you make sure your UAVs meet international norms and standards. We test materials and resilience, confirming that your drones do not pose a threat to human health or the environment. Our team of experts is dedicated to UAVs and their applications – and a global network of offices. We can give you the advice and expertise you need to speed your drones to market. Our team of experts is dedicated to UAVs and their applications – and a global network of offices. We can give you the advice and expertise you need to speed your drones to market.
-
product
Universal Transmitter
Model LXT-380
Teledyne Analytical Instruments
The Model LXT380 transmitter is a single or dual channel, intelligent, multi-parameter designed for the online continuous measurement of pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity and resistivity. The Model LXT380 Tramsitter digitally communicates with the SP3X digital sensor, automatically configuring the trasmitter's menues and display screens to the measured parameter. The LXT380 tramsitter can be Loop powered or 4-wired DC powered. The standard configuration has a 4-20 mA and a serial communication port with MODBUS RTU output. Alarm relays option is only available on 4-wired DC powered transmitters. LXT380 Transmitter loop is available in FM, ATEX and IECEx certifications.
