Data Acquisition
senses the physical, represented as an analog signal, that is then converted to digital data. Also known as: DAQ
See Also: Data Acquisition Systems, PCI Data Acquisition, DAQ, Digitizers
-
Product
Data Acquisition System
Pixie-16
-
The Pixie-16 is a data acquisition system for nuclear physics and other applications requiring coincident radiation detection with large number of channels.
-
Product
Data Acquisition DSP Based 16 Channel
CPCI-AD8-opt8
-
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
Product
PXI 32-channel High Voltage Data Acquisition
M9216A
-
The M9216A is a high voltage data acquisition module that allows simultaneous measurement of eight channels of positive voltages ranging from 1 mV to 100 V. Each channel comes with a concurrent 5 V and 100 V measurement range, with every channel capable of acquiring very low and very high voltages without the need for switching ranges.
-
Product
Data Acquisition System
DAQ973A
-
Get the next-generation data acquisition (DAQ) system with a three-slot mainframe and your choice of nine plug-in modules. Interface with the DAQ using Keysight BenchVue DAQ software or use the intuitive graphical front panel with task-oriented, self-guiding menus.
-
Product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
-
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
Product
64-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2355A
-
The U2355A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
Product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
-
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
Product
Data Acquisition Module for Embedded Systems with IO60 expansion
IO60-M410
-
WINSYSTEMS’ IO60-M410 is a reliable data acquisition module for embedded systems with IO60 expansion featuring 24 GPIO (General Purpose Input-Output) tolerant to 30 V DC. Activity LEDs indicate device communication and DAC fault. WINSYSTEMS can provide custom configurations for OEM clients. Please contact a Applications Engineer through our contact page for details.
-
Product
8-CH Analog Input Module
ND-6017
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Data Acquisition Software
-
The very powerful data acquisition software from Elsys transforms the data acquisition hardware into a measurement solution that can be used directly after little training.
-
Product
Data Acquisition DAQ
-
Keysight Technologies has provided data acquisition (DAQ) and switching solutions for more than twenty-five years. We provide data acquisition solutions for electrical, physical, mechanical, acoustic and signal routing applications up to 50GHz.
-
Product
PCI Data Acquisition Boards
AD8S-100DMA Series - Single low-spur 8-bit, 100 Ms/s
-
Model AD8S-100DMA is similar to the AD8-100DMA, has a single low-noise eight-bit 100MSPS A/D converter and can acquire up to 100 MS/s on a single channel into the host system's RAM. Drivers for 64 bit Linux and Solaris operating systems included.
-
Product
PCI Data Acquisition Boards
AD8-1250DMA Series - 8 bit, 1.25 GS/s
-
Model AD8-1250DMA contains a 1.25 gigasample/second 8 bit A/D, 8 GB of on-board SDRAM memory and the ability to transfer data directly into the computer system's memory at up to 320 MB/s on 64-bit PCI systems.
-
Product
PCI Data Acquisition Boards
ADDA12-100DMA Series - Dual 12-bit A/D + Dual 14-bit D/A, 25 Ms/s
-
Model ADDA12-100DMA has two simultaneously sampling 12-bit A/D converters, two 14-bit D/A converters, five vectored TTL inputs and two vectored TTL outputs, and is able to transfer data directly into the computer system's memory at 100 MB/s in systems with 64-bit PCI slots or 80 MB/s in 32-bit slots.
-
-
Product
Complete Data Acquisition System
ScopeLogicDAQ
-
ScopeLogic - complete data acquisition system - consists of Digital Oscilloscope and Logic Analyser. This small instrument is making the accurate analysis of complex analog-digital signals possible - thanks to simultaneous sampling finding relationship between these signals is easy. The user is able to simultaneous use 16 digital channels and 2 analog channels with standard scope probes.
-
Product
Data Acquisition Unit
-
The Teledyne Test Tools T3DAQ1-16 is a 16 channel Data Acquisition System incorporating the latest 4.3 inch (10.92 cm) dual-display technology which can be configured to show Data Histograms, Data fluctuation Trends, Bar Graph, Statistics or the traditional Number mode, all in an easy-to-use interface.
-
Product
3-CH RTD Input Module
ND-6013
-
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Data Acquisition & Control
-
With these DAQ systems, you can acquire and digitize signals from variety of sources and sensors, store the data, analyze it, and present the results in local and remote locations.
-
Product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
-
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
Product
Remote Data Acquisition
-
Sometimes your sensors or the piece of equipment you are trying to control is not in a convenient place to have a PC close by. The sensors may be widely distributed through out your plant and it just wouldn’t be cost effective to run all your wiring to where the PC is. In addition, low level signals are more accurately acquired when digitized close to the signal source. In all these cases our REMOTE ACCES line of products will help. The REMOTE ACCES pods are intelligent, sensor to computer interfaces. Each pod can be used as an autonomous data logger to acquire data for later download. Or as many as 31 pods may be connected on a single two wire multidrop RS-485 network allowing a cable distance of up to 4000 ft. You can also go wireless and extend your range by adding RS-485 wireless transceivers to your serial port. Each unit comes in a rugged NEMA 4 enclosure and can withstand harsh industrial and marine environments.
-
Product
Data Acquisition
-
From one to hundreds of measuring channels, AOIP data acquisition systems enable users to measure, remote display, monitor through any network, record and process any kind of physical and electrical sensors.
-
Product
64-CH 12/16-Bit Up to 3 MS/s Multi-Function DAQ PCI Express Cards
DAQe-2200 Series
-
ADLINK DAQe-2200 series are highdensity and high-performance multi-function DAQ PCI Express cards. The devices can sample up to 64 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with high-density analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 32 AI channels in order to achieve maximum noise elimination.
-
Product
Strain Measurement Data Acquisition Modules
-
Automated strain measurement systems allow you to test measuring and experimental equipment as well as to combine data for the purpose of engines tests, tests of various components, manufacturing technological processes control and many other industrial applications.
-
Product
SIRIUS Data Acquisition (DAQ) System
SIRIUS
-
Measure anything precisely. We build the SIRIUS line of instruments for one purpose only measure any kind of signal, anywhere, in any environment with flexibility, precision and ease of use you have been dreaming of. SIRIUS offers endless configuration possibilities: from 4-channel 200 KS/ch distributed USB solutions to high speed 128 channel standalone solutions with built-in PC and display.
-
Product
Data Acquisition Unit CATCH
MS 1523
-
CATCH is a web based locomotive monitoring system. This system provides locomotive data on Internet. Locomotive data are automatically download and organized at one place. The downloaded data can be viewed from anywhere through the Internet. By this flexibility the decision taking authority can get into an action immediately.
-
Product
Data Acquisition & Analysis
-
American Environments Co., Inc.
American Environments facilities are equipped with automated data acquisition systems.
-
Product
cPCI Data Acquisition
-
The cPCI data acquisition product line provides a variety of high-speed digital conversion cards from 50MS/s, 100MS/s, 500MS/s to 4GS/s. These conversion cards feature 8-, 10-, and 12-bit resolutions, as well as wide bandwidth and large acquisition memory. The high-speed digitizer, when configured into a data acquisition system, provides basic multi-channel oscilloscope functionality in a compact chassis.
-
Product
PXI Data Acquisition
DAQ
-
Installation and configuration is fast and easy with standard connectors, soft front panels and Keysight connection expert. In addition, software drivers support the most common programming environments such as Visual Studio®, C, C++, Visual Basic, MATLAB® and LabVIEW™.
-
Product
PCI Data Acquisition Boards
AD8-1500DMA Series - 8 bit, 1.56 GS/s
-
The AD8-1500DMA series has a 1500 MSPS 8-bit A/D, 8GB/16GB of on-board SDRAM memory and the ability to transfer data directly into the computer system's memory at up to 320 MB/s on 64-bit PCI systems. Sampling is controlled by an onboard oscillator or by an external clock input, which may be in the frequency range between 20 MHz and 1500 MHz. Multiple boards may be configured to acquire either concurrently, for more simultaneous acquisition channels, or sequentially, with an automatic overlap selectable from 0 to nearly 2GB, in 512KB steps, for longer record length. Drivers for 64 bit Linux and Solaris operating systems included.
