EMI Receivers
measure conducted and radiated emissions for compliance to EMC standards.
See Also: EMI, RFI, Near Field Probes
-
product
Micro Coax/Micro Power, Module, Receiver, 90 Series, 120 Positions
510104270
Micro Coax/Micro Power, Module, Receiver, 90 Series, 120 Positions.
-
product
MIPI Receiver Test Solution
M8085A
The M8085A is a software plug-in for M8070A Bit Error Ratio Test system software within the M8000 series of BER test solutions. The M8085A software plug-in controls either the M8190A or the M8195A Arbitrary Waveform Generators to create C-PHY or D-PHY standard compliant test signals. In addition it provides routines for calibration of all signal parameters and for all tests specified in the applicable Conformance Test Suite. Together with the additional available DUT control interface it is possible to read the BER of the receiver under test from the M8070A software and display the BER dependency from test parameters within the M8070A user interface.
-
product
Signal, Module, Receiver, QuadraPaddle, 480 Position, Unloaded
510150116
Primary mating module 510151106. (May mate with other ITA modules, as well.)
-
product
Ground EMI Filters
High-frequency signals on ground is never good news - it interferes with normal operation of equipment and creates electrical overstress (EOS). However it is easy to block propagation of EMI on ground by installing highly-effective ground EMI filtes in ground lines. Our unique patent-pending ground EMI filters provide very low impedance for DC and mains' power while effectively blocking propagation of high-frequency currents throughout facility or equipment ground. Ground filters meet safety standards, as well as ANSI/ESD S6.1 and ANSI/ESD S20.20.
-
product
90deg Hybrid With Balanced Receiver
This page describes one of Optoplex's innovated products, a 90deg optical hybrid integrated with balanced photo-receivers, which can be used in optical sensing applications, particularly the coherent Doppler wind LIDAR (light detection and ranging). Coherent detection has been widely found in applications for RF and optical communications. In the past few years, coherent technology has been advanced dramatically in high-speed optical communications. With this advancement, key parts and components are commercially available and cost-effective for many applications beyond telecommunications, such as narrow linewidth lasers, optical hybrid, balanced photo-receivers, and DSP, etc.
-
product
Tool, Locator, TriPaddle, Receiver
910104146
Tool, Locator, TriPaddle, Receiver (only for contact p/n #'s 610110128 Rev C+ and 610110177)
-
product
Optical Receiver Stress Test
N4917BACA
A complete, automated, and repeatable solution for optical receiver stress test.
-
product
Signal / 20-26 GHz / 75 Ohm HD, Module, Receiver, TriPaddle, iCon Series, 64/8 Position
510160115
iCon modules mount from the rear of the iCon receiver and ITA and allow installation and removal of pre-wired cable blocks. Primary mating module 510161115. (May mate with other ITA modules, as well.)
-
product
Digital Wideband Receiver Family
IZT R3000
The IZT R3000 is a professional digital hf, vhf and uhf receiver. Its world-class rf performance and state-of-the art digital signal processing make it the ideal sensor for direction finders, signal recording and COMINT systems. The IZT R3000 has been ordered by the German Federal Network Agency as ITU-compliant Monitoring Receiver.
-
product
Coherent Optical Receiver
IQRX
The IQRX is a “gold standard” coherent receiver for the measurement of coherent modulation formats such as QPSK, 64QAM and OFDM.Its high-bandwidth, low-noise architecture makes it ideal for high-quality, low-distortion coherent signal measurement.With two built-in lasers and convenient touchscreen LCD front panel control, the IQRX delivers quick and reliable measurements.
-
product
40Gb/s DQPSK Receiver
The integrated DQPSK receiver incorporates an optical phase demodulator (delay-line interferometer or DLI) with 2 pairs of balanced photo-diodes and 2 linear TIAs into a single butterfly package. Compared with the currently available discrete solution in which a separate DLI and a separate receiver are used, the integrated DQPSK receiver eliminates labor intensive fiber routing and coupling (between the DLI and the balanced receiver) as well as the skew control. Moreover, the integrated DQPSK receiver offers a smaller footprint suitable for today’s demanding high speed transponder applications.
-
product
DisplayPort 2.0 Receiver Test
N5991DP2A
Use the Keysight N5991DP2A DisplayPort 2.0 Receiver Test Software to test, debug and characterize your DisplayPort Sink products maximizing the usage of your test instruments.
-
product
ITA, I2 MX, EMI, XL Backshell (XL Bend Radius and Cable Exit)
410130126
This model i2 MX includes the backshell only and does not include module inserts or front protective cover. The XL-size backshell allows for a greater cable bend radius and large cable exit. The max cable bundle eff diameter= 1.67".
-
product
ITA, 9050, 50 Module, Double Tier, for EMI
410104577
ITA, 9050, 50 Module, Double Tier, for EMI
-
product
Replacement Protective Cover, G2, Receiver
310113394
The Receiver Protective Cover is provided to keep your modules and contacts enclosed when the Receiver is not in use. Part 310113394 is included with every 310120110 receiver.
-
product
Waveguide Receiver Protector
The continuous evolution of radar systems creates an ever more complex RF power environment in which sensitive receivers must operate and survive. Teledyne limiters deliver vital protection for a wide range of receivers, providing protection from L-Band through to Ka-Band (1 - 40GHz) and peak power levels up to 1MW with unparalleled low insertion loss levels.
-
-
product
Multi-standard Cable/terrestrial Receiver For PCIe
DTA-2131
High-quality VHF/UHF receiver with support for all popular cable- and terrestrial standards, including ATSC 3.0, DAB, DVB-T2 and ISDB-T. The SDR approach enables full-channel reception (all services), advanced RF measurements and graphs.
-
product
Compact Receiver Module
MixAMC-I
Virginia Diodes'' standard Spectrum Analyzer Extension Modules (SAXs) provide high performance broadband down-conversion and frequency extension of microwave specturm analyzers into the THz range. VDI now offers integrated MixAMC modules that provide industry leading performance in a compact package. These integrated MixAMC modules are used to down-convert millimeter-wave / THz signals only. Spectrum Analyzer Extension mode is not currently available for the MixAMC-I products. Integrated MixAMC modules utilize a low frequency LO input (<20 GHz) and have a seprate IF output port. Integrated MixAMC modules configured for high IF bandwidth may be available upon request.
-
product
CATV RF Optical Receiver
L-RF-MN-RX
The QuestTel''s L-RF-MN-RX module optical receivers are versatile, low-cost and compact optical receivers for use in HFC fiber applications. It is perfect solution for the transport and distribution of CATV RF signals over fiber optic cable. The L-RF-MN-RX module housed in a small housing and have adjustable RF output level. May be used as a hand held device for testing, or placed at a customers premise for the reception of cable television services. The Receiver is designed to operate with a very low optical input level between the range of +3dBm to -12dBm.
-
product
Receiver Compliance Test Automation Platform
Test a wide range of digital high-speed buses with a fast and reliable solution including system calibration and one button compliance tests.
-
product
GNSS Software Receiver
SX3
With IFEN’s SX3 frontend measurement synchronization betweenIF-sample data and external sensor data (as IMU or barometer for example) is possible,as well as integration of user defined algorithmswithin the SX3 application programming interface.
-
product
Telemetry Receivers
2U R200A Series
Systems Engineering & Management Company
R200A Series Receivers are designed for fixed and mobile Telemetry Ground Stations, but particularly for mobile applications where space is at a premium. The R200A provides for many of the same configurations and options available with the larger R600A and R400 systems, using the same cards, modules and RCMS network software for optimum interoperability. In addition, the RT200 Tracking Receiver configurations are an extremely popular, low cost solution for antenna tracking installations. The R200A provides the same proven performance and reliability and user interface of the R600A and R400. Like the R600A and R400, a "non-PC" configuration is available for remote operation via Ethernet. The 2U R200A receiver has become one of SEMCO's most popular receivers in terms of small form factor and operational performance and reliability.
-
product
Digital Receiver XMC
XF07-516
Curtiss-Wright Defense Solutions
The XF07-516 is a rugged quad channel 250MSPS 16-bit digital receiver XMC. The ADC devices directly interfaces to a user programmable Xilinx FPGA which allows high performance processing such as Digital Down Conversion (DDC), filtering and custom algorithms.
-
product
Wireless Sensor Transmitters, Receivers & Displays
High accuracy, high quality measurement is interfaced with simple yet powerful configuration and monitoring software. T24 gives sensor manufacturers and integrators the complete flexibility to build their own sensor modules around it. The system easily replaces wired systems, reducing installation and maintenance costs.
-
product
Micro Coax, Contact, Receiver, RG316
610140101
Primary mating contact 610141101. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outerCable Specifications RG316Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Mini Two Output Extra-low Receiving Uni-directional Optical Receiver
9082 (Out-door)
Hangzhou Huatai Optic Tech. Co., Ltd.
9082 is an economic extra-low receiving uni-directional receiver. It is commonly used in "fiber to building" and some remote houses in the village . It is out-door type and its power supply is 220V or 60V.
-
product
Visual Analysis Tool for GNSS Receiver Data
Panorama
Panorama is the flagship tool when it comes to analyzing receiver data. When engineers use Panorama they spend more time looking at plots and making decisions, instead of making plots and writing reports. Panorama takes receiver data (.csv files) from PANACEA and RxStudio (other ODS products) and turns it into over 60 engineering plots ready to view at the click of your mouse. These plots give engineers and analysts the ability to view summary level data, head to head comparisons, receiver specific results, and 3D LLA replays using STK.
-
product
SATA 3 Receiver Test Automation Software
N5991ST3A
The N5991ST3A is the latest receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize SATA devices and hosts.
-
product
Micro Power, Contact, Receiver, PCB Mount
610142108
Micro Power, Contact, Receiver, PCB Mount.
