Infrared Sensors
Detect infrared radiation and produce a measurable signal of the detected amount.
-
Product
Power Sensor and SNS Noise Source Cable (6.1m/20 feet)
11730C
Power Sensor
The Keysight 11730 series power sensor cables are used with the 8480 and E-series power sensors (except the E9320 family of peak and average sensors). These cables are designed to reduce RFI effects on low power readings with an improved shielding design in the cable itself. Cables may be ordered individually or in pairs in any combination desired for single and dual-channel measurements.
-
Product
S2 Blinx Digital Sensors
ULP-S2 BLINX
LED Sensor
The Universal LightProbe S2 Blinx Digital is designed for the simple ON/OFF test of any color blinking or steady-state LED, for fast results with a digital output. The Universal LightProbe S2 Blinx Digital Sensors check the ON/OFF status of any color LED, whether stable or blinking/pulsed, up to a rate of 15 Hz, and provide a Logic “1” output (5 volts) only if the LED is “ON” and a Logic “0” if the LED is “OFF.”Operating temperature range: 0oC to 70oCPower consumption: Operates from +5, 12, 24 or 28 volts D.C., at 6mA max.Voltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Load: 20mA max. (Source/Sink). Non-inductiveOutput Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longOperating Temperature Range: 0hC to 70hCTypical response times: <66mS, shorter for brighter LEDsFiber-Optic Probes: Wide Aperture Fiber-Optic Probe recomended
-
Product
Infrared Thermometer
MT-4612
-
Ideal for measuring of mechanical, chemical, pottery,food, metallurgy, electric power, air condition,high-temperature heat treatment.
-
Product
Infrared Microscope
DDR200/300 NIR
-
The McBain DDR200 NIR (for 200mm) and DDR300 NIR (for 300mm) provide high-speed defect detection and precision measurement on wafers and other parts. These cost-efficient systems offer unique advantages for both production and process development use, providing an optimum near-infrared (900-1700nm) solution when both subsurface defect detection and dimensional metrology are required.
-
Product
High-Accuracy Infrared Thermometer [Built-in type]
IT-270
-
IT-270 is a built-in type Infrared thermometer with industry-leading* accuracy in a small footprint. Measurement temperature, wavelength selection and viewing characteristics can be customized to meet various needs.
-
Product
Fourier Transform Infrared Spectrophotometer
IRSpirit
-
Despite their small footprint, smaller than an A3 size sheet of paper (297 x 420 mm), these models have been engineered with a wide sample compartment that accommodates existing accessories from Shimadzu and other manufacturers. This capability makes them the smallest (installation footprint) and lightest FTIR spectrophotometers in the world that can be used with optional products from other manufacturers. They also include a program, IR Pilot, with 23 application-specific workflows that can be utilized without involving any complicated parameter setup process. Customers can select from either the IRSpirit-T model, which offers sensitivity equivalent to standard Shimadzu models, or the reasonably priced IRSpirit-L model.
-
Product
SparkFun Grid-EYE Infrared Array Breakout
AMG8833 (Qwiic)
-
Get ready to be able to see like the Predator! The SparkFun Grid-EYE Infrared Array Breakout board is an 8x8 thermopile array, meaning you have a square array of 64 pixels capable of independent temperature detection. It’s like having a thermal camera, just in a lower resolution. To make it even easier to to get your low-resolution infrared image, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Infrared Thermometers
-
Two specifications tell you nearly everything you need to know about any infrared (laser) thermometer: its measurement range and its distance-to-spot (D:S) ratio. The wider the range and the higher the D:S number (a measure of its optical resolution), the better the instrument. Infrared Thermometers (IRTs) with lower numbers are perfectly adequate for simple tasks like spot-checking food temperatures and energy auditing such as the IRT207 Non-Contact Infrared Thermometer. Higher-priced infrared thermometers intended for industrial users may have a SKU that ends in "K" such as the IRT850K Ultra-Wide-Range Infrared Thermometer with K Port and Adjustable Emissivity. The "K" indicates that it can accept inputs from a "K" type thermocouple probe used to measure temperature on-contact.
-
Product
Non-Dispersive Infrared Monitors
OPTI-Sense Series
-
Teledyne Advanced Pollution Instrumentation
The OPTI-Sense series of sensors is based on Non-Dispersive Infrared (NDIR) technology. They are designed to precisely measure the absorbance in the infrared spectrum of specialty gases typically found in semiconductor applications. They are very compact and designed with no moving parts, making the OPTI-Sense robust and ideal for continuous in-situ gas monitoring of semiconductor processes.
-
Product
Sensor
Lepton
-
The FLIR Lepton™ is the most compact longwave infrared (LWIR) sensor available as an OEM product. It packs a resolution of 80 × 60 or 160x120 pixels into a camera body that is smaller than a dime. This revolutionary camera core is poised to equip a new generation of mobile and handheld devices, as well as small fixed-mount camera systems, with thermal imaging capabilities never seen before. Lepton contains a breakthrough lens fabricated in wafer form, along with a microbolometer focal plane array (FPA) and advanced thermal image processing. In order to support the lepton and make it easy to use, we have developed a breakout board to support the module along with example source code. Please see the Lepton Thermal Camera Breakout Datasheet for more information.
-
Product
Longwave Infrared Thermal Camera Module
Tau® 2
-
Made in USA, the Tau® 2 OEM thermal imaging cameras offer an unmatched combination of features and reliability, making them well-suited for demanding applications including unmanned vehicles, thermal sights, and handheld imagers. Improved electronics provide powerful image processing modes that dramatically improve detail and contrast through continuous histogram equalization. Radiometry is available in every pixel for both 640 × 512 and 336 × 256 resolutions and all three camera grade levels. All Tau 2 configurations share electrical, mechanical, and optical interfaces allowing integrations to be designed that work seamlessly with all formats. Available in Commercial, Performance, and Industrial variants, each with unique sensitivity and pixel operability thresholds to meet operational requirements. Radiometry is an optional feature for Performance-grade cameras, and standard feature with Industrial-grade. All Tau 2 configurations and resolutions share electrical, mechanical, and optical interfaces allowing integrations to be designed that work seamlessly with all formats.
-
Product
10 MHz to 33 GHz LAN Wide Dynamic Range Average and Peak Power Sensor
L2063XA
Power Sensor
The Keysight L2063XA is a fast, accurate and wide dynamic range 10 MHz – 33 GHz LAN peak power sensor.
-
Product
Infrared T1 3/4 LED
350-00003
-
T1 3/4 Infrared light emitting diode, for breadboard or through-hole projects. Used with the LED Standoff and LED Light Shield to build the IR Transmitter Assembly (#350-00017). Frequently used with the IR Receiver for object detection and autonomous robot navigation, this is a compatible replacement wherever an Infrared LED is found in any of our Education Kits Components Listings.
-
Product
Infrared Gas Detector
iTrans2
-
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
-
Product
Infrared Gun-Style 50:1 w/Laser
425
-
Gun-Style Infrared thermometer with Dual Laser Sighting, LED Flashlight and Hi/Lo Alarm. With HDPE carrying case and magnetic stand.
-
Product
Sensors
-
As traffic management challenges intensify, ITS strategies prioritize the multitasking capabilities of intelligent detection sensors. Econolite’s sensors exceed basic traffic detection by performing tasks like counting, classifying, tracking, and providing advanced detection for adaptive systems and dilemma zone safety. In modern multimodal intersections and roadways, advanced detection sensors are indispensable, featuring capabilities for bicycle and pedestrian detection and differentiation.
-
Product
Sensor Six-Pack
PT-6
-
PT-6 Sensor Six-Pack - For multi-point temperature measurements. Inexpensive, Flexible. Welded sensor beads, tough kapton insulation. Diameter is .029''. Maximum temperature 350°C, Time constant 0.01 Seconds. 5 foot lead. Not isolated.
-
Product
Inductive Sensors
-
Our hygienic sensors are extremely durable against abrasive and aggressive media: their labeling is resistant to abrasion and chemicals. The luminous displays are protected against destruction and the housing construction is optimized for safe cleaning.
-
Product
ChromaLine Sensor
MPLS-DM
-
Sciences et Techniques Industrielles de la Lumière
Based on STIL's chromatic confocal technology, ChromaLine sensor family represents the next step in industrial integration.Thanks to its accuracy, its robustness and a life span of several years without any maintenance, MPLS sensors are adapted to the requirements of on-line control.
-
Product
Pressure Sensors
-
Whatever configuration you require, look to Sensata. Our devices span a spectrum of pressure ranges, configurations and form factors.High pressure (>750psi / 50bar)Micro Silicon Strain Gauge solutions provides rugged reliability and a hermetic seal for a wide variety of environmentsMid pressure (100 to 750psi / 6 to 50 bar)Ceramic capacitive or MEMS solutions offer a wide range of solutions tailored to application needs at superior valueLow pressure (inches of water to 100psi / 2mbar to 6 bar)MEMS solutions including TPMS offer extremely low power consumption and wireless connectivity
-
Product
Magnetic Sensors
-
Magnetic sensors are used for the detection of positions without contact or wear and tear. They are used where very long sensing ranges are required. Since magnetic fields penetrate all non-magnetisable materials, the sensors can detect magnets through walls made of stainless steel, aluminium, plastic or wood.
-
Product
Humidity Sensors
-
A humidity sensor is a device that detects and measures water vapor. TE Connectivity (TE) manufactures a complete range of calibrated and amplified RH sensor products to measure relative humidity. Based on our robust capacitive technology, these humidity detectors provide accurate measurement of dew point and absolute humidity by combining relative humidity (RH) and temperature (T) measurements.
-
Product
Dual Input Thermometer And Infrared Thermometer
-
We hereby certify that this product has been calibratedand found to be in accordance with the applicableSPECIFICATIONS and STANDARDS.Accuracies of the standard equipment used inthis calibration are traceable to the National Standards
-
Product
Web Sensor
P8511
-
Web Sensor P8511 is designed to connect one probe. To Web Sensor P8541is possible connect up to four probes. Temperature or humidity probes are available asoptional accessories
-
Product
Temperature Sensors
-
It is used by many factory because of its simple and convenient temperature measurement.
-
Product
Process Sensors
-
To achieve the highest product quality, to minimize production and maintenance costs, and to react immediately to deviations in the production line, the continuous control and analysis of the production process are mandatory. The improved visibility of all process steps goes hand in hand with increased product quality. Therefore, the best process instrumentation is required.
-
Product
Sensor Technology
-
Power Monitoring and Diagnostic Technology Ltd.
PMDT is the only manufacturer to utilize all 5 types of online partial discharge sensor technology. Using multiple sensing methods ensures that PD activity is always discovered, located, and characterized. PMDT's handheld PDetector and PDStar units have more capability than the high-end diagnostic equipment of the past. The small handheld, battery powered unit can completely perform the test and analysis without the need of a PC. PDetector, PDStar, and PDiagnostic instruments feature high-resolution phase-resolved analysis of PD signals (PRPD and PRPS) in real time, so you get your test results instantly!
-
Product
Proximity Sensors
-
Premier Electrosystems is an esteemed name in the manufacturing of inductive proximity switch, photo sensors, capacitive sensors, magnetic sensors, hall effect sensors, analog sensors, encoders, infrared sensors, etc. with NABL calibration certificate
-
Product
Medical Sensors
-
The pressure sensors listed below are available in a wide range of shapes, sizes, pressure ranges, and resolutions.
-
Product
Infrared Thermometers
-
Non-contact Infrared Thermometer Sharply Focus on Measurement Spots with Two-Beam Laser Marker, Ideal for HVAC Applications
