Capacitance Bridges
A bridge that compares capacitance of a reference capacitor to DUT.
See Also: Capacitance
-
Product
Capacitance Detection Probe
Which Ender
-
By sensing capacitance the Which Ender identifies if a wire is connected to a contact. When the Which Ender's button is pressed, a tone is produced. If a contact is connected to a wire, this tone will drop in pitch when the probe tip touches the contact. The Which Ender is essential for locating opens, breaks, and unused pins in connections.
-
Product
Capacitance/Loss Bridge
AH 2550A
-
The AH 2550A offers unparalleled stability, resolution and accuracy in a capacitance/loss bridge (whether manual or automatic). Its numerous state of the art features make it an exceptionally user-friendly instrument, just as was its predecessor, the AH2500A. The precision and ease of use of the AH2550A are creating new applications in science, calibration, and production in a wide range of fields.
-
Product
Bridge Rectifier Assemblies
-
Bridge Rectifier Assemblies are constructed by packaging diodes and/or SCR components with heat sink extrusions in a bridge circuit.CEHCO uses M, T, N and W heat sink extrusions to build rectifier assemblies.
-
Product
4-20mA Bridge AmplifierR
90416
-
This miniature, on-board, transducer amplifier is capable of supplying excitation voltage and amplifying millivolt signals from strain gage based transducers.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
779521-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Capacitance Sensor Systems
-
MTI Instruments offers high resolution capacitance sensors, probes and systems that generate low noise, highly accurate and high stable measurements. Our Capacitance sensor line-up offers accurate measurements for automated inspection applications such as thread quality inspection, disk drive run-out, leveling or flatness measurement, lens alignment, tire run-out and bulging. Our Accumeasure capacitive sensors offer large stand-off distance that includes single and multiple channel rack systems that connect up to 10 capacitive sensors or capacitance probes with individual analog measurement outputs. We also offer cost-effective customized capacitive sensor amplifier board and probe system for easy integration. Our inspection systems linearity exceeds 0.01% full scale measurement (FSM) and resolution to sub nanometers.
-
Product
Capacitive Product Selector
Elite Series
-
Highest performance, most versatile modular capacitive displacement sensor systems. High resolution, wide bandwidth, display and control options.
-
Product
PLD For Bridging, Infinitely Reconfigurable I/O Expansion.
MachXO
-
*Up to 27.6 Kbits sysMEM™ embedded block RAM and up to 7.7Kbits distributed RAM*SRAM based logic can be reconfigured in milliseconds using JTAG port*IOs support LVCMOS, LVTTL, PCI, LVDS, Bus-LVDS, LVPECL, RSDS*Up to two analog PLLs per device that enable clock multiplication, division, and phase shifting*Available in TQFP, csBGA, caBGA and ftBGA packages
-
Product
Capacitance Standard
SCA Series
-
The SCA Standard Capacitor series are highly stable cost-effective capacitance standards with low temperature coefficient, low losses and a wide range of values of 1 pF - 10,000 F. The cost and flexibility make this our most popular capacitance standard.
-
Product
Repair of Six Diode Bridge Assemblies, P/N 5989C
-
CEHCO is specialist in repair of various rectifier assemblies. One such assembly is shown below:Specifications:- Six Diode Bridge Assembly, P/N 5989C- AC input terminals: (3, 4 , 5)- DC output terminals: (1), POSITIVE and (2), NEGATIVE
-
Product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781209-01
Strain/Bridge Input Module
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
Product
Capacitance Tan-Delta Test Set
-
Since our establishment in the year 1975, we have been engaged in manufacturing and exporting Capacitance Tan-Delta Test Set. This test set is extensively used to measure dissipation and capacitance of various equipment. Manufactured at our well-equipped manufacturing unit as per set international quality standards using supreme quality components, this test set is tested thoroughly by our quality analysts on various defined parameters. Offered Capacitance Tan-Delta Test Set can be purchased from us at pocket-friendly prices.
-
Product
Gateways And Bridges
FarLinX Mini Gateway
-
A compact remotely manageable X.25 to TCP/IP Gateway with XOT and PAD support.
-
Product
Decade Box, Calibrated, Capacitance, 5, 100pF to 11111µF, 5 %
72-7265 CAL
-
The 72-7265 CAL from Tenma is a capacitance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set at any non polarized capacitor value from 100pF to 11,111µF in 100pF increments. The decade accuracy is ±5% capacitors used throughout at <1μF, 1KHz test frequency, ≥1μF, 100Hz test frequency. It has weight of 304g/0.69lb and dimension is 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
Portable Bridge Structures Control System
-
Portable bridge structures control system is a set of digital modules and intelligent sensors placed inside of a compact case. Basic delivery scope of the system includes:
-
Product
Resistance Bridges
-
Provides the best in measurement uncertainties for Direct Current Comparator (DCC) Resistance Bridges. Unique innovations in 6622A design and modularity means users no longer have to decide what Bridge satisfies current requirements as well as future requirements. Optional modules allow for normal, high ohms, and low ohms measurements without having to purchase multiple bridges as per competitive products.
-
Product
CAPACITANCE METER
C350
-
This is a high quality digital capacitance meter. Check the accuracy and status of capacitors up to 20mF, a very handy tool for virtually any technician. It features high accuracy (0.5%) and 9 selectable ranges. A zero adjustment knob is also provided to "zero" test lead capacitance. Includes test probe set and yellow rubber boot.
-
Product
CAMAC-to-FERA Bridge
CFB
-
The WIENER CFB is an intelligent, programmable, re-configurable CAMAC-to-FERA bridge with sequencer that allows one to interface both, common and custom-made CAMAC modules to FERA-readout-based data acquisition systems.
-
Product
Capacitive Touch Controllers
TouchXpress
-
Silicon Labs' TouchXpress devices are highly optimized solutions that enable designers to easily design and integrate capacitive sensing into applications. These devices quickly replace mechanical buttons and switches with modern capacitive touch buttons by eliminating the firmware complexity and reducing development time.
