Phantom Loads
generate different current values based upon the current rating of the energy meter under test. 2) standby power of a device turned off.
See Also: Parasitic Drain
-
Product
Power Load Switches
-
Low-resistance power load switches offer reliable overcurrent and thermal protection. They are designed for general-purpose power protection or for applications such as USB, hot-swap and power distribution. The power switches come in 1- or 2-channel versions with fixed and adjustable overcurrent limit. Some include a USB charge controller specifically designed to optimize USB host applications.
-
Product
NO LOAD & LOAD TEST BENCH
-
International Biological Laboratories
These are the test benches incorporating control & measurement circuitry necessary for testing single phase as well as three phase transformers of several VA to MVA rating & voltage class of 11KV/433V,as well 33KV/11 KV, after manufacturing, repairing, reconditioning. Following tests can be done by these Test Sets.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
Load Cells
-
Selection of load cells must always be guided by the end users particular system requirements and by the application. The PIAB Load Cells range from typical compression/tension load cells to S-beam and shear beam types for stationary applications as well as for mobile weighing systems.
-
Product
Load cell simulator
PC2M
-
PC2M signal calibrator has been realised to perform periodicalchecks and calibrations on indicators with a 2mV/V input anda 4 or 6 wires systems. Provided with a main switch with 6 selectable steps, it allows to control the linearity on both positive and negative field. Internally, the 350W full bridge unbalancing, is generated by high stability passive resistances (1 ppm/C).
-
Product
Channel Load Generator
802.11p
-
Qosmotec Software Solutions GmbH
When many cars are equipped with 802.11p communication technology, high traffic density will also cause significant load on the radio channel. From normal wireless communication systems it is a known problem, that many users can cause a complete breakdown of the network. Car-to-X communication technology tries to protect itself against those kind of breakdown by a carrier sensing mechanism: Each communication device has to check first, if the radio channel is busy. In that case, it waits for a random delay to avoid packet collision on the radio channel, which causes a loss of both collided packets.
-
Product
Load Cell Transducer
-
Unitech Scales And Measurements Pvt. Ltd
Force can be measured by different methods, one of the most effective and accurate method is by using strain gauge based load cells. Four Transducer class strain gauges are bonded on the specimen and are connected in the form of Whetstone Bridge. The specimens are of different types depending on the requirement such as S, column, beam, ring, shear beam, binocular etc. UNITEH’S Load Cells are used for wide applications rite from commercial weighing scale to industrial process controlling, R & D applications and educational institutions. UNITECH’S manufacture load cells from 1Kg to 100Tons for compression or tension or universal (Compression and tension) applications. We also undertake custom built load cells for specific requirement and for OEM users.
-
Product
AC Electronic Load
-
AC&DC Electronic Loads are design for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources and other power devices such as switches, circuit breakers, fuses and connectors.
-
Product
4kW Electronic Load
PT04-48
-
For Telecom Rectifier and Power Supply testing. This model has been developed to accommodate testing of both 48V and 24V telecommunications power systems or Power Supplies. It is also useful as a general-purpose variable Load. Its founding principle is simplicity – ease of use, enhanced reliability, greater value for money and wider applicability.
-
Product
Load Tester for D Type Durometers
-
A load tester for checking the spring load characteristics of ASKER hardness testers at the hardness readings of 25, 50, and 75.
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
DC Electronic Load
-
DC electronic loads are designed for testing a wide range of power conversion products including AC/DC and server power supplies, DC/DC converters, EV batteries, automotive charging stations, and other power electronics components. These units can be synchronously paralleled up to 240kW and dynamically synchronized for generating complex multi-channel transient profiles. The 300% peak overpower capability provides extra headroom for fault condition simulations in automotive batteries, fuel cells, and more.
-
Product
AC Load Bank
-
PC software controls offer advanced load profile solutions and model options range from small, portable, low-power units, to high-power indoor or outdoor permanent load solutions.
-
Product
Unclamped Inductive Load Tester
ITC55300C
-
Model ITC55300C performs ruggedness testing of power MOSFETs, discretes and modules and IGBTs, discretes and modules. It also tests single and dual diodes, and forward and reverse bias of IGBTs when used with an optional ITC55-RSF Output Selector Box.
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
cPCI Load Boards
-
VECTOR Electronics and Technology, Inc.
Vector Electronics & Technology, Inc. cPCI resistive load boards provide a means to test power generated and cooling capability of cPCI systems.
-
Product
Regenerative DC Electronic Load
IT8300 Series
-
ITECH newly launched IT8300 Regenerative DC Electronic Load, it not only can simulate various load characteristics, but also can feed power back to grid without pollution. IT8300 series unique regenerative function can convert the absorbed DC power into AC power and feed it back to local grid.
-
Product
Load Cells & Force Transducers
-
BLH and Nobel Weighing Systems offer a wide variety of load cells and force transducers, ranging from the unique KIS load cell and weigh module to the VPG transducers range of products. Our many years of experience, our state-of-the-art instruments, and the exceptionally broad range of components that go into our systems allow us to deliver high-quality solutions tailored to your needs.
-
Product
Spring Loaded Connector 20A
Swift-Dock-Ultra-Power®
-
For applications with current loads up to 20 amps. With a pitch of 10mm, this is our largest and most rugged or our Swift-Dock range of spring loaded interface assemblies. Ideal for... Rapid battery charging, Rugged environments, Data-loggers, Telecoms devices.
-
Product
Load Banks
-
From battery discharge testing to power equipment verification, our load banks are designed for precise testing and maintenance, helping you maintain peak performance and compliance with ease.
-
-
Product
Road Load Data / Durability
-
Vehicle Durability Testing and Road Load Data AcquisitionA road load data acquisition system from Dewesoft is a perfect vehicle durability testing solution for real-drive tests or tests on the road simulator test benches. Our advanced DAQ technologies will shorten time to test dramatically and make sure you get the correct measurements right the first time.
-
Product
On Load Tap Changer Analyzer
TAP-4-PLUS
-
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
Product
Electronic Load System
-
Electronic loads are required for testing fuel cells such as PEMFC, AFC, PAFC, MCFC, SOFC. These electronic loads are designed either in IGBT technology with power, current and voltage ranges according to specific requirements or in transistor technology. Electronic loads in IGBT technology are designed for high voltage ranges up to 900 V, current ranges up to 1000 A, and power ranges up to 480 kW.
-
Product
DC Loads
-
Becker Nachrichtentechnik GmbH
Becker Nachrichtentechnik offers wideband multichannel DC decouplers for antenna diagnostic applications. Due its high bandwidth the device is suitable for all broadcast, cellular and Wi-Fi standards.
-
Product
Electronic Loads
-
The DSO and DSOT series electronic loads are designed using advanced linear technology.The DSO series offers two main functions: constant current and constant resistance. However, these loads can absorb full power between 20% and 100% of the acceptable input voltage thanks to the autoranging mode.For more extensive requirements, we offer 'DSOT' models that also include constant voltage and constant power functions. These functions are essential for testing voltage generators such as automotive alternators or photovoltaic panels to determine their power curve. In addition, DSOT models have a basic '0 Volt' characteristic, which means they can be used with input voltages as low as 0 Volt. However, they still maintain a high reaction speed, which can reach 1V/us and 8A/us.
-
Product
Beam and Singlepoint Load Cells
-
We have trimmed all the non-essential fat off these load cells, however you can be sure that nothing has been trimmed from the actual load cells, they are precision tested and certified to meet all the exacting requirements on the downloadable technical specifications shown below.
-
Product
Generator Loading System
-
Mosebach Manufacturing Company
GLS (Generator Loading System) is a load bank for use with your generator to load it automatically to your set point. This will keep your generator running at its optimal point and reduce your maintenance costs. Fully programmable by you.
-
Product
Resistive Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Resistive load banks are an important tool for testing and verifying the performance of power systems such as generators, UPS systems and turbines. They simulate real-world electrical loads by dissipating power as heat through resistive elements.
-
Product
Electronic Load Mainframe GPIB
3300 Series
-
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
