GPS Simulators
-
product
GPS Amplifier/Splitter
The amplifiers has typically 40 dB of gain while the splitters can split an antenna from 4 to 20 ways.
-
product
1 Or 2 Stream MIL-STD-1553 PMC Test And Simulation Modules With Prog. Coupling,onboard Bus Network And Variable Output Amplitude
AMCX1553-xT
MIL-STD-1553 Test and Simulation modules for PMC with 1 or 2 Dual Redundant streams plus 8 Discrete I/O’s (on Rear-I/O).
-
product
LED Solar Simulator
LumiSun-50
The LumiSun-50™ is a high power, multi-wavelength LED solar simulator that meets IEC 60904-9 Class AAA for spectral match, uniformity of irradiance, and temporal stability. The LumiSun-50 achieves a spatially uniform illumination field from a chip-on-board (COB), multiple-wavelength LED die array. The field of illumination is 50 x 50 mm at a working distance of 200 mm. The LumiSun-50 includes a driver/controller which individually provides constant current to each die in the COB array. Total irradiance of 1.1 sun units is provided and can be decreased to 0.1 suns. The LED light source of the LumiSun-50 is contained within an air-cooled housing that can rotate the angular beam alignment. Adjustment and setting of the optimum light path working distance is visually facilitated by a converging pair of red dot laser pointers.
-
product
Impulse Noise Simulators
INS Series
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
product
Signal Architect Simulator Software
GNSS
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
product
Transducer Simulator
Model 7V
Impedance: 350 ohms nominal. Output Ranges:Fixed rotary switch: 0 to 3 mv/v in 6 steps of .5 mv/v .
-
product
GPS DRIFTER
Microstar
A low-cost current following drifter designed to track currents at 1m to 5m beneath the surface. The Microstar was specifically designed to meet the unique challenges of coastal environments as a shallow water small scale current measuring platform.
-
product
PXI/PXIe Battery Simulator Module, 2-Channel
41-752A-003
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Radar・Sensor Simulation Framework
COSMOsim
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
product
Solar Array Simulator DC Module, 65V, 8.5A, 510W
E4361A
The Keysight E4361A is a 510W solar array simulator DC power module that simulates the output characteristics of a solar array. The E4361A is primarily a current source with very low output capacitance. It offers fast I-V curve changes allowing you to accurately simulate the output of different solar arrays under various environmental conditions (ex. temperature, age, eclipse, spin etc.). The E4360 gives you the flexibility to operate it in two ways:
-
product
4, 8, 16 Or 32 Channel ARINC429 Test And Simulation Modules For VME (6U)
AVC429-x
Integrated modular solution by using the AMCX429-x PMC cards installed on AIM’s AVC-2 Generic VME64x (6U) carrier card.
-
product
Flash Solar Simulators
Sciencetech manufactures a range of flash solar simulatorsSee the Flash Solar Simulator Overview to compare products across different product lines.
-
product
Fibre Channel PXI Express Test & Simulation Instrument
PXIe-FC4
Avionics Interface Technologies
3U PXIe form factor will fit into any PXIe or hybrid slot - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Triggering and Filtering - Error Injection on any Header or Payload Parameter - Data Capture to on-board memory or disk file - Live Capture and Current Value Monitoring - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Supports HS-1760E applications, including AS5653, AS5625, and AS5627fcXplorer Windows-based FC Simulator and Analyzer Test Software
-
-
product
Simulate millions of real-world end-user environments
PerfectStorm
Keysight Network Applications and Security
The next generation of our well-received PerfectStorm 10/40GbE platform is available now. PerfectStorm 100GbE is the world's only native 100GbE testing platform, far ahead of other test solutions, the closest of which offers just 10GbE native interface support. The new platform comes to market at the right time, as equipment sales of 100GbE are ramping in Service Provider and Enteprise Data Center.
-
product
Single Or Dual Stream MIL-STD-1553A/BTest And Simulation Module For Standard Ethernet
ANET1553-x
The ANET1553-x is a member of AIM’s new line of Ethernet based modules for analysing, simulating, monitoring and testing MIL-STD-1553A/B databuses. For wireless applications, an ANET compatible USB Wifi dongle is optionally available. The capability to execute Python scripts in the ANET is a standard feature. For applications with multiple ANET devices AIM offers the ADock ANET Docking Station to host up to 4 ANET modules.
-
product
MIL-STD-1553 A / B Test And Simulation PMC Module
PMC-1553
*Dual redundant*1, 2 or 4 channels*Simultaneous bus controller, 31 remote terminals, bus monitor*Error entry and detection*FPGA based hardware architecture*Multi-level trigger for data acquisition and filtering*10 programmable, discrete I / O (up to 30V)*IRIG-B timecode encoder / decoder with free-running mode*Real-time recording and physical bus playback*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, LabView Real-Time and other systems*Heat sink and / or protective coating available*Optional input / output for front panel
-
product
ARINC 429 PXI Express Test & Simulation Instrument
PXIe-C429
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Panel-mounted Power Amplifier(Hardware In The Loop Simulation)
PA30Bi
PA30Bi is the panel-mounted type real time simulation amplifier with three-phase current and four-phase voltage.
-
product
USB2.0 Module With 2 CAN Bus Nodes ARINC825 Compliant For Testing & Simulation of Avionic ARINC825/CAN Bus Systems
APU825-2
USB2.0 module with 2 CAN bus nodes ARINC825 compliant for testing and simulation of Avionic ARINC825/CAN bus systems.
-
product
Emulate Test in simulation
STIL-VT
Emulate test patterns in simulation environment with DUT simulation model. The simulation allows pre-silicon debug of test patterns. Reads the intermediate STIL format of tester patterns and creates a Verilog /VHDL simulation test bench. (A sub-set of Virtual tester solution)
-
product
2 Port 10/100/1000Mbit/s AFDX/ARINC664P7 Test, Simulator And Monitor Module For PCIe
APE-FDX-2/B
AFDX®/ARINC664P7 Test and Simulation module for PCIe x1 with 2 full duplex ports programmable for 10/100/1000 Mbit/s. Versions available for both Airbus and Boeing variants of ARINC664P7.
-
product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
product
ARINC 429 Test & Simulation Interface for VME
VME-429
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
SIMULATOR
458-LM-A8-18A
Simulates 26 AWG PIC as specified in ANSI T1.417Bandwidth DC to 18 MHzIdeal for testing ADSL, ADSL2, ADSL2+, ADSL2++, VDSL,VDSL2(supports up to Profile 17a) modems/DSLAMs8 channels per line moduleLoop lengths programmable from 0 to 15,000 ft in 1,000-ft incrementsPlugs into our Model 458-CC-16 (16-slot) or 458-3SLB (3-Slot)chassisChannel-to-Channel isolation up to 90 dB
-
product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Acceleration Simulation Mode Roller Set for Vehicles with a Single Driven Axle
ASM-BF/1 | VP 230043
Maschinenbau Haldenwang GmbH & Co. KG.
The ASM-BF/1 roller set is used in test centres and is suitable for vehicles with a single driven axle. It was designed for the exact measurement of the exhaust gas behaviour of vehicles during their transient emission test and permits a driving resistance simulation for the exhaust gas tests ASM-5015 and ASM-2525 (Acceleration Simulation Mode) in accordance with the specifications BAR '97.
-
product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 750 V Isolation
43-752A-012
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Training & Simulation Devices
Designed to minimize instructor input and provide realistic, automated response.
-
product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
