Leakage Current Clamps
Measure low current emf surrounding a conductor.
-
product
Metra ACDC Clamp 1000A
Metra Clamp 1000A /300A measures important electrical parameters like AC Current, AC Voltage, DC Voltage. It also features Capacitance, Ohm & Continuity, frequency, Duty cycle and temperature meas-urement.
-
product
Flexible AC/DC Current Tester
FCM-400
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Bending free flexible clamp sensor*Measuring ranges AC/DC 0.100A～300A(Min. resolution 0.001A)*Big CT window (φ450mm)*Easy accessibility to the hard to clamp object
-
product
Current Transformer
ST-60CT
Standard Electric Works Co., Ltd
● 400/5A - 800/5A● 7.5-10V A● Class 1● Insulation 600V
-
product
Leakage Current Monitor
LCM500
The Doble LCM500 Leakage Current Monitor can measure condition while a surge arrester is still in service, measuring the quality of the metal oxide blocks and helping manage the risk of failure.
-
product
Current Clamps and Sensors
Are designed for measuring leakage current diverted towards the earth. It enables the fault to be located or anticipated without disconnecting the equipment linked. It is specially designed to detect low fault currentson power circuits.
-
product
AC/DC Clamp Milliammeter (CE)
M-700
MULTI MEASURING INSTRUMENTS Co., Ltd.
*High sensitive for low range leakage current.*Suitable for measurement of 4-20mA DC controlled circuit.*DC mV analog signal output.*Lowest influence from Magnetization and Terrestrial magnetism.*Wide measuring ranges up to DC 1000mA and AC 10A.
-
product
Current Signature Analysis
The Iris Power MDSP3 uses the Current Signature Analysis technology which relies on the concept that faults in the induction motor rotor or driven components result in changes to the rotor magnetic field pattern. Unique magnetic rotating fields are produced due to the faults which induce detectable stator current components indicative of the fault.
-
product
Mini Digital Clamp Tester
M-210+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・23mmφCT window and ultra compact size.・Data-hold function. Especially useful when working in dark or hard to get areas.
-
product
Opto-Isolated Current Loop Signal
4029
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
product
Current Tester
MIG0624
The MIG0624 current tester is designed to test surge protection devices for low voltage applications (<1000 V). MIG0624 is a current generator delivering a 8/20 µs impulse up to 24kA. The exact waveform delivered is a function of the surge generator and the impedance to which the surge is applied.
-
product
AC/DC Clamp Meter
2660 CL
Standard Electric Works Co., Ltd
● 4000 counts.● Voltage measurement, current measurement, resistor measurement, frequency counter, capacitor measurement.● Bargraph indication.● Range change function.● Data hold function freezes the reading.● REL function.● Peak function.● Diode measurement.● Max / Min function.● Continuity check.● Low battery indication.● Auto Power Off (APO) function.● Safety design throughout with no exposed metal parts, shielded banana plugs and recessed input terminals.
-
product
Clamp on Meters
2000 counts LCD displayData hold for easy readingAuto-power offSafety as per IEC1010-1, Cat.II 1000V
-
product
Tidal Current Flow Meter
KDL’s tidal current flow meter gives you the ability to monitor the speed and direction of tidal currents . Tidal flow speed information is extremely important to aid shipping movements such as berthing.
-
product
Bluetooth Integrated Clamp Meter
This is a Bluetooth with memory Integrated Wireless Connectivity AC Clamp Meter
-
product
Leakage Test
Leakage current and discharge current depend on the insulation of the device. The measurement simulates various fault situations that could occur during operation. The test determines whether the measured current is within the permissible limits and poses no danger to the user in case of a fault.
-
product
Low Noise Current Preamplifier
SR570
Stanford Research Systems, Inc.
The SR570 is a low-noise current preamplifier capable of current gains as large as 1 pA/V. High gain and bandwidth, low noise, and many convenient features make the SR570 ideal for a variety of photonic, low temperature and other measurements.
-
product
C/I Clamp Meters
CLAMPMETER,OPEN JAW (CSJ-100)
*AC amperage, AC/DC voltage measurement*Open jaw design eases AC current measurement*Slim profile with build-inprobe storage on back*Measures resistance up to 20MΩ*Audible continuity and diode test*Bright LED and audible alarm for non-contact voltage detection*Auto power off for longer battery life*Data hold to capture measurements*2000 count LCD*Accessories included: (2)1.5V AAA batteries, test leads and carrying case*Lifetime Limited Warranty
-
product
High-Voltage Differential Probe, 25 MHz
N2791A
Use the N2791A 25-MHz low-cost high-voltage differential probe to make safe and accurate floating measurements with an oscilloscope. The N2791A differential probe allows conventional earth-grounded Keysight oscilloscopes to be used for floating signal measurements of up to 700 V of differential voltage and common mode voltage.
-
product
AC Current Sensor
LFR
The LFR ac current probe has been designed to have market leading low frequency performance, meaning low phase shift and low noise. This compact, low cost, clip-around probe is both flexible and dual-range, and is optimized to give minimal phase measurement error at frequencies from 45Hz to 20kHz and have a very low noise floor.
-
product
Digital Clamp Meter
DL369
UEi Test & Measurement Instruments
The PHOENIX Clamp meter series starts with the DL369, the perfect meter for contractors who need basic features without all the extras. Great for general troubleshooting and electrical maintenance, this isn't just a stripped down model, the PRIME is a fully functional tough meter made to get the job done.
-
product
Eddy Current Testing
MIZ-200
The MIZ-200 eddy current instrument can handle the most demanding environments with ease. Offered in both tubing and surface array configurations, MIZ-200 is ideal for applications within Balance-of-Plant/Power Generation, Transportation and Oil and Gas markets.
-
product
DC Bias Current Source
DU2020/2030/2040
Delta United Instrument Co., Ltd.
Frequency: 10KHz - 200KHz Veracity:3% + 3 digitsTiming: 0.1 - 999 H, settable 3 1/2 bits LCD Display
-
product
Time, Current, And Resistance Meter
AllWin Instrument Science and Technology Co., Ltd.
1. Time, current and resistance can be displayed simultaneously2. Out put current:5~30A. Ground resistance range: 50~600 mohm
-
product
Phase Meter Current Shunts
610 and 650
Clarke-Hess Communications Research
The Model 610 and 650 Current Shunts are specifically designed to operate with the Model 6000A Precision Phase Meter. These shunts are frequency tuned to have negligible phase shift (less than 5m) at 50/60Hz making them ideal for line frequency applications. They can also be idealized for other frequencies as specified by the user. Consult factory for details.
-
product
Zero Phase Current Transformer
MZL-45
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
product
8-Ch SPST 20A-250VAC High Current
YAV90087
8 power relays Switching 20A 250Vac PNP Outputs para control or YAV90304 control CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
Current Probe
PA-655
*Max. ±50A DCA*Resolution: ≧5mA*Bandwidth: DC~500KHz*Rise Time: 0.7us*Over Range Function*20mV/A, 200mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
product
Pressure To Current Measurement Trainer
Unitech Scales And Measurements Pvt. Ltd
Pressure to Current (P to I ) Trainer:This setup comprises of pressure chamber fitted on a base board. A pressure transducer and bourdon pressure gauge are fitted to the chamber. Digital pressure indicator with transmitter output is provided to display the pressure sensor by the pressure transducer. Transmitter output 4 to 20mA can be measured by a current meter. Foot air pump is provided to build the pressure.
-
product
Check Current Before Working
Radio Ampstik® 2023
The Radio Ampstik uses the same current sensor technology as the original SensorLink Ampstik. It quickly takes accurate current measurements and direction of current flow indication. Knowing source and load direction is essential for power system protection, load balancing, and metering.
-
product
Cryogenic Current Comparator (CCC)
6200A
Measurements International Ltd.
Introducing the Model 6200A Cryogenic Current Comparator Bridge (CCC) from Measurements International (MI) – the ultimate solution for achieving the highest level of resistance calibration accuracy. With an uncertainty of less than 3 parts in 10-9, our CCC surpasses all other technology on the market.
