Multifunction DAQ
-
Product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable, 2m
192061-02
Multifunction Cable
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair, Shielded Multifunction Cable - The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths.
-
Product
MultiFunction Calibration
-
Omega offers a large selection of configurable Multi-Channel Meters that accept a wide variety of input signals for scanning, displaying, and logging measured data from multiple sensors.
-
Product
Multi-Functional Power Meter with LCD Display
PM135
-
The PM135 provides a cost-effective substitute for numerous analog meters used by industrial, commercial and utility customers for basic power metering.
-
Product
Cable, 10 Pos Combicon to Pigtail, 2 Meters
190656-02
Multifunction Cable
The SH10M-10F Cable, sometimes referred to as SH10F-P, connects C Series DAQ devices with a 10-pin screw terminal to open signal wires. The SH10M-10F Cable is offered in different lengths.
-
Product
Multifunction Tester
COMBI521
-
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Multifunctional Scratch Hardness Tester
-
Sataton Instruments Technology CO., Ltd
Multifunctional scratch hardness tester is an integrated testing instrument designed for cross hatch cut method and five-finger (five arm) method to measure scratch or mar resistance, hardness, susceptibility of a material surface to different physical damage like scratching, marring, scraping, etc. The tester are made of two parts, one is for determination of resistance to scratches and cuts according to cross-cut test for paints and varinishes. The other is for
-
Product
Multi-Functional Dynamic System Monitor
PFMonitor
-
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
-
Product
DAQ Devices
-
LabJack makes USB/Ethernet based measurement and automation devices which provide analog inputs/outputs, digital inputs/outputs, and more.We provide a robust and highly supported interface between computers and the physical world.
-
Product
RCONAF-EC
Multifunction Cable
A 6”cable transitions from the card edge connector on the RAF-EC-2P (champ 36) to one male HD-15 connector and two shielded RJ-45 connectors.
-
Product
Multifunctional Immunity Test System For Automotive Electronics
EMS-ISO7637
-
EMS-ISO7637 automotive multifunctional immunity test system meet newest ISO7637-2 requirement of
. This standard was issued by international organization for standardization, and this system included all of ISO-7637 required test waveform and meet most of automotive manufacturer’s requirement for automotive electronic immunity test. -
Product
High Voltage Multifunction Phasing Sticks
PC7K / PC11K / PC22K / PC33K / PC44K
-
Kusam Electrical Industries Limited
* Designed to Exceed VDE 0681 part 5.* Dual Color Coded Scale (%, Vac).* Neon indicator lit when >1200 Vac.* Compare between Phases.* Measure and test Phase to Earth.
-
Product
Configurable 3U OpenVPX Multifunction I/O Boards
Multifunction I/O
NAI offers a variety of 3U VPX solutions, including rugged I/O Boards and SBCs - designed to be combined with our smart function modules - to create a COTS-based, high-density, multifunction I/O solution for most sense and response requirements.
-
Product
80 I/O Multifunction Module
YAV90832
Digital I/O Module
16 Analog Inputs 0…15Vdc 10 Bits Zin= 1,2MOhm 24 Digital Inputs (Trigger) 32 Digital Outputs 11…45V/650mA 4 Analog Outputs 0…10Vdc 10 Bits 4 Outputs PWM CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Multifunctional Meter
CPM-12
-
CPM-12 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.Hardware can be option a a RS485 Modbus communication port.Auto wiring change (Note) via softwareCE and FCC approved
-
Product
Multifunction Tester
M70
-
M70 is a mobile device dedicated to measuring Insulation resistance with test voltage up to 1000VDC and Continuity of protective and equipotential conductors with current of 200mA in private and industrial electric installations.
-
Product
USB-6343, 32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device
782252-01
Multifunction I/O
32 AI (16-Bit, 500 kS/s), 4 AO (900 kS/s), 48 DIO USB Multifunction I/O Device - The USB‑6343 offers analog I/O, digital I/O, and four 32‑bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB‑6343 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Multifunction Data Collection and Analysis System
2002
-
The Model 2002 DME System is a state of the art, multifunction data collection and analysis system. It is suitable for application in an electrical utility substation or plant environment to produce Sequence of Event (SER), Digital Fault Recorder (DFR), Dynamic Disturbance Recorder (DDR), and Continuous Recorder data in conformance with PRC-002-1 and PRC-018-1. All data recorded by the DME system is stored in IEEE C37.111 format and named in conformance with IEEE C37.232. The system also has a software option to enable the Phasor Measurement Unit (PMU) feature to provide streaming data in conformance with IEEE C37.118.
-
Product
Multifunction I/O
526
-
Four 24-bit quadrature encoder inputsFour 16-bit analog outputsEight 16-bit analog inputsEight digital I/OSingle supply (5 V) input powerProgrammable interrupt timerVersatile watchdog timerxPC Target Real-time rapid prototyping softwareavailable through MathWorks
-
Product
Multifunction Instrument for Education and Training
LabXplorer
-
LabXplorer turns your desktop, laptop, tablet or smart phone into a powerful, multifunction test and measurement instrument for a wide range of applications. Instruments, whatever you need, are at your fingertips. LabXplorer provides multimeter, oscilloscope, spectrum analyzer, logic analyzer, programmable analog and digital signal generator, impedance analyzer and also measures characteristics of passive electronic components and semiconductor devices.
-
Product
USB-6361, 16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device
782256-01
Multifunction I/O
16 AI (16-Bit, 2 MS/s), 2 AO (2.86 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6361 offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6361 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
110-250V AC Multi-Function Screwdriver Voltage Tester
5120A
-
Peaceful Thriving Enterprise Co Ltd
With CE, GS and UKCA Approval. Operates by two LR41, 1.5V batteries. Test for voltage, continuity. By contact method, check on 110-250V AC. By non-contact method, check on 110-500V AC. Detecting pulse of the high-tension ignition.
-
Product
6-24V Multi-functional Auto Tester With LED Display
6510A
-
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
Product
Multifunction Installation Testers
-
Shanghai Beha Electronics Co., Ltd.
Loop impedance and prospective short circuit current measurement• Line impedance and prospective short circuit current measurement• Earth loop resistance in TT-systems• Rotary field test• RCD measurements (contact voltage, trip time, trip current - ramp method)• RCD analysis for test of all RCD parameters • Low Ohm and continuity measurement • Insulation measurement up to 1000V (suitable for 690 V industrial mains systems)• Earth resistance measurement with probes and clamp adapters• Voltage and frequency measurement • Current measurement with clamp adapters(optional)• Power and energy measurements• Harmonics measurement for voltage and current upto the 21st harmonics
-
Product
M12 Cable, 2-Pin Female Connector to Pigtail, 5 m
196648-05
Multifunction Cable
M12 Cable, 2-Pin Female Connector to Pigtail, 5 m
-
Product
Multi-function Double Way Datalogger
VA602-A1-R1
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Multi-function record meter is a new record meter designed for the actual demand of various industrial site, which integr.
-
Product
150 KS/s, 12-Bit, 16-Ch Multifunction USB Module
USB-4711A
-
Supports USB 3.0 SuperSpeedBus-powered16 analog input channels12-bit resolution AISampling rate up to 150 kS/s8-ch DI/8-ch DO, 2-ch AO and one 32-bit counterDetachable screw terminal on modulesSuitable for DIN-rail mountingOne lockable USB cable for secure connection includedPortable
-
Product
Multifunctional Meter
AEM-DR
-
Provide high accuracy measurement, display and remote communication of single phase & three phase parameters (V, A, P, Q, S, PF, Hz, Kwh). Multicircuit design and relay output modular expansion design decrease the overall cost and make the functionality more flexible. All monitored data is available via a RS485 serial , for the needs in energy management, alarming, and remote controlling. Embedded flash memory for Data-Logging can avoid any data missing once the communication is interrupted. Moreover, its ultra compact size DIN-rail mounting makes itself mountable in virtually any panel, enclosure or indoor Cabinet.
-
Product
Multifunction Meter
MPI-530-IT
-
Short circuit loop measurement:*impedance measurement with 23 A (44 A phase-to-phase), short circuit resistance Rzw=10Ω,*measuring range: 95...440V, frequency 45...65 Hz,
-
Product
DB9M-Pigtail, 9-Pin D-SUB Male to Pigtail I/O Cable, 2 m
157867-02
Multifunction Cable
9-Pin D-SUB Male to Pigtail I/O Cable, 2 m
-
Product
3U OpenVPX Multifunction I/O Board
68C3
Multifunction I/O
NAI’s 68C3 is a 3U OpenVPX multifunction I/O and communication board with three function module slots that can be configured with a variety of I/O and communication functions. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
