Resistance Decade Box
set of precision resistors configured in desired resistance values.
See Also: Decade Box, Capacitance Decade Boxes, Inductance Decade Boxes
-
Product
8-Port Junction Box
-
Teledyne Marine Cable Solutions
A heavy-duty junction box designed for use in high-risk environments where the cost of failure is significant.
-
Product
DC Resistance Tester
ZLD-10
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.5-2008/IEC60851-4; Inspection standard: JB/T4279.2-2008Used to measure conductor with nominal diameter ≥0.01～9.0mm or various round or flat copper and aluminum wires and other metal wires with DC current resistance of 100μΩ～99.99Ω;Combination of intelligent DC conductor resistance measuring meter and DC resistance test fixture with sample straightening function;Test range can be selected according to the resistance value of sample, and after clamping samples current resistance value would be displayed;Both potential fixture and current fixture are made of copper;The application of microcomputer control allows for full-automatic completion of test;LED will intuitively display measurement results;
-
Product
3 Wire (Digital) Earth Resistance Tester
2720 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Battery test indication.● Calibration performed with supplied test leads.
-
Product
Resistance Tester With Leakage Current (Loop Current)
GT00WD00ZY
-
*screen display*Double protection insulation*Non-contact measured resistance, safe, fast
-
Product
Surface Insulation Resistance Testing
-
Following over 2 years of intense research and development, we are proud to introduce the next generation of equipment used to measure changes in Surface Insulation Resistance.
-
-
Product
Winding Resistance Meter 15Amps, 2 Channels Rack
WR14R
-
Raytech Digital Winding Resistance meter WR14 R is the rack mount version of the WR14. They are designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
Corona Resistant Tester of Enamelled Wire
DPT-1000S
-
Shanghai Dean Electrical Co., Ltd
·The tester is comply with the requirements of standards GB/T 1707-2008, GB/T 24122-2009, GB14711-2013, meet the requirement of standard JB/T 10930-2010;·Multiple samples can be tested at same time;·Used for testing the feature of high frequency pulse resistance (performance of Corona-resistance).
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TT Series
-
RMO-TT series is perfect for measuring winding resistance of inductive objects such as power and distribution transformers or autotransformers. Additionally, every transformer resistance meter from RMO-TT series can analyze:tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.Transformer demagnetization can also be performed with all RMO-TT instruments.The series is consisted of 3 models, with maximal test current from 40 A (RMO40TT) to 100 A (RMO100TT). RMO100TT is the only portable transformer resistance meter in the market with 100 A DC output current.The three independent channels enable testing of three windings in series. Consequently, a user can measure winding resistance in every tap position of an on-load tap changer without discharging between the tests.In addition to winding resistance measurement, a user can perform a detailed on-load tap changer analysis by analyzing recorded graphs (10 kHz sampling rate) and by measuring vibrations on an external tap changer tank.All RMO-TT instruments have a built-in tap changer control unit. Because of this, it is possible to remotely control on-load tap changer (OLTC) directly from the device. Also, a user can program DV-Win software to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
Product
Surface Resistance Tester
MR – 1
-
The different specific resistances are specified by selecting one of the pre-programmed materials, or by measuring the specific resistance of unknown materials and entering the result. Preferably the coat thickness is displayed, but the measurement and display of the actual resistance, the square resistance and the specific resistance is possible, too. All measured values can be transmitted into a PC via a serial interface. Controlling the MR-1 on the other hand is not possible.
-
Product
Manual Switch Boxes
-
RTI's manual switch box is a portable and versatile test solution for quick IC electrical verification tests. RTI's 96-pin manual switch boxes integrate with a variety of test configurations that are customized to your test and device needs. It requires no software and connects directly to an external power supply for bias test, and performs quick comparison tests using an A/B relay box.
-
Product
3D inversion geophysical software for Resistivity and Induced Polarization Data
RES3DINV
-
This program is designed to invert data collected with a rectangular grid of electrodes. The arrays supported include the pole-pole, pole-dipole, inline dipole-dipole, equatorial dipole-dipole and Wenner-Schlumberger. The RES3DINV program uses the smoothness-constrained least-squares inversion technique to produce a 3D model of the subsurface from the apparent resistivity data alone.
-
Product
1KV Insulation Resistance Tester
2680
-
Shenzhen Chuangxin Instruments Co., Ltd.
1KV insulation resistance tester
-
Product
3 Wire (Digital) Earth Resistance Tester
1120 ER
-
Standard Electric Works Co., Ltd
● Waterproof: IP54● Capable of measuring earth resistance and earth voltage● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test● The test leads are supplied as standard accessories for simplified two-wire measuring system● 0Ω adjustment● Battery operated● Data hold function● Low battery indication
-
Product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
-
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
-
Product
4 2/3 Digital Resistance Meter (1/32 DIN)
CS3-RS
-
CS3-RS Resistance Indicator has been designed with high accuracy, display, control, remote communication.A compact body design for small equipment, laboratory instrument, and others.Also are available with relay output, analog output, RS485 Modbus RTU communication to cover a wide range of applications.
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
3 Wire (Digital) Earth Resistance Tester
1820 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● The test leads are supplied as standard accessories for simplified two-wire measuring system.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.
-
Product
Cost Effective Capacitance Decade Box
CS Series
-
The CS Series Capacitance Decade Box is a cost effective and commonly used capacitance decade box for production and educational applications
-
Product
Resister
-
Our ARFC type Film Flat Chip Resistor & ARFCN type Thin Film Chip Resistor Network are high precision Metal Film resistors produced with high purity. Alumina Substrate and Ni-Cr-Si Resistor Film based on high precision Etching Technology. The electrode Terminals are made with Spattering Film and Nickel-Solder Plating, and solderability is very good in all Flow, Reflow and Dipping type soldering for Hybrid IC, SMT, PCB etc. Our ARFC Metal Film Resistor & ARFCN type Thin Film Chip Resistor are being produced under the thorough quality control, and are being used widely in high precision and high reliability electronics circuit such as Measuring Instrument, Medical Instruments, Communication and other Industrial Instruments.
-
Product
Transformer Resistance Testing
-
Transformer insulation resistance deterioration is one of the most common causes of transformer failure: a failing transformer is a costly replacement in an electrical system with the potential for a long downtime. If you fail to maintain your transformer with regular insulation resistance testing (as can be carried out by the Megger Transformer Ohmmeter (MTO) series of transformer test equipment) then it’s likely to fail before reaching its maximum operating life.
-
Product
DI Boxes
-
Applied Research and Technolgy
Instrument DIs for stage and studio, plus specialized tools to connect virtually any source to a mixer, interface, or PA.
-
Product
Field thermal needle system for thermal resistivity / conductivity measurement
FTN01
-
Hukseflux Thermal Sensors B.V.
The FTN01 Field Thermal Needle System allows performing fast, on-site measurements of the thermal resistivity or conductivity of soils, in particular around the typical depth of burial of high voltage cables. FTN01 is designed with a focus on robustness and saving time, while still offering sufficient accuracy for typical field measurements. The sensor is a Non-Steady-State Probe (NSSP), TP09, which is mounted at the tip of the Lance LN01. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Zero Resistance Ammeters
-
Current sinks are electronic circuits which can sink electric power in a controlled manner, thus acting as controlled loads. Our current sinks are designed as four - quadrant current sinks which can feed and sink currents in both polarities (also disregarding the polarity of the resulting voltage).
-
Product
Insulation Resistance Tester for PV (2 range)
MIS-PV1
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
The model MIS-PV1 is an insulation resistance tester for the exclusive use in photovoltaic systems. The ordinary insulation resistance testers cannot make measurement properly during generation of PV systems. This instrument, however, can measure the insulation resistance simply by touching probe to the live line whether making generation or not. There are two ranges of PVH and PVL. PVH is for high voltage generation system (more than 500V and less than 1000V) and PVL is for the system less than 500V.
-
Product
Edge AI Box
-
Arm-based edge AI boxes are powered by NXP, NVIDIA and Rockchip. They provide AI inference capabilities in a low-power fanless design.
-
Product
Terminal Box Knock Out Tester
-
King Design Industrial Co., Ltd.
Since the solar panels and power junction box are exposed to the sun and rain, therefore, if junction box can sustain for several years or even several decades without damaged and maintain normal supply of electricity, it will become critical equipment for the solar power parts manufacturers making quality assurance testing to their commodities.
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
-
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
Product
VB Build-A-Box
-
The VB Series, Build a Box provides a solution for any combinations of signal transport over fiber. With the VB-10 (10 card slots), VB- 6 (6 card slots), VB-4 (4 card slots), a unit can be created to your specification by populating the case with any configuration of VB-Cards. Each card’s I/O can be sent or received over its own disparate fiber, or all signals in the box can be multiplexed onto just one fiber. Inherently portable, each unit is ready for field applications or can be rack-mounted with optional Rack Mount kits.
-
Product
Ground Resistivity and EarthService Tester
AD-510
-
Large, readable LCD display (2000 counts), Instant battery life indicator, Test frequency: 128 Hz (quartz generator), Test Voltage: max 30 V peak-to-peak, Range: 0,01 W ? 2 k W. Accuracy resistance measurement: 1 % 2 digits,
