Three Phase Energy Meter
-
Product
AC Clamp Meter
2950 CL
-
Standard Electric Works Co., Ltd
● Pocket size.● 4000 counts.● Full automatic measurement. Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (Auto off in 1 minute).
-
Product
UL496 Lampholder Torsion Meter
CX-DTN
-
Shenzhen Chuangxin Instruments Co., Ltd.
This Lampholder Torsion Test Device is strictly designed according to UL496 etc. It's mainly used to the screw lampholder torsion test of protecting accidental force.
-
-
Product
Phase Splitter Comb Generator
-
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
Product
W Series Panel Meter
ST-160
-
Standard Electric Works Co., Ltd
● Measuring Range : DC uA-200, 500 DC A -1, 5, 10 DC V -5, 10,15, 20, 30, 50, 100, 150, 300, 500● Accuracy : Class 2.0● Case and Composition: Acrylic Resin front and ABS Resin case Bezel mounting● Color：Black case, yellow scale plate.● Pointer：Tube type, black or red LED Custom ranges depend upon warrant quantity Suitable for VU meters of Amplifier usage
-
Product
Electro Magnetic Meter
-
This meter is used to indicate radiated electromagnetic fields. Wherever there is a voltageor a current, electric (E) and magnetic (H) fields arise.
-
Product
General Purpose Benchtop XRD System for Phase I.D. and Phase Quantification
-
In a move to bring lab-quality performance to the manufacturing floor, Rigaku introduces the MiniFlex XpC, a manufacturing-optimized powder diffractometer for fast and accurate quality control measurements. It is extremely easy to operate using Rigaku’s new EasyX quality control software, which requires minimal clicks to run. A minimal interface means there will be no accidental error variance from operator to operator. The MiniFlex XpC can be configured with a conveyor belt or robot for automated sample processing and collaboration with other instruments. With an 800 W X-ray source and a short-diameter goniometer, the system has the performance of a lab unit, and thus can greatly improve throughput for quality control measurements.
-
Product
Material Moisture Meters
-
The testo 606-2 moisture meter measures the moisture content in wood, building materials and the surrounding environment. This allows you to check storage and drying conditions quickly and easily.
-
Product
EMF/ RF Field Strength Meter
-
Designed for measuring and monitoring Radio–Frequency electromagnetic field strength.
-
Product
Water Cut Meter
-
The Drexelbrook Universal IV Series products feature full compensation for both temperature and density as well as multiple mounting options which includes insertion and spool piece probes.
-
Product
Smart Heat Meters
-
Ultrasonic heat meter is a kind of instrument used to measure and display the released heat power when the heat-carrying liquid pass through the heat exchange system.
-
Product
Digital Panel Meter
DC
-
Laureate DC voltage and current panel meters with a DC signal conditioner board combine high accuracy with high read rate and a wide range of isolated output options for computer interface and control. Accuracy is 99.99% of full scale 1 count. Used as a direct-reading DC voltmeter, the Laureate provides a full-scale readout of 20,000 counts and six full-scale voltage ranges from 200.00 mV with 10 mV resolution to 600.0 V with 100 mV resolution.
-
Product
Voltage Control Phase Shifter
-
RF Lambda’s voltage control phase shifters use an analog control voltage to vary the phase of an RF signal. They are available in a variety of frequencies and overall phase shift ranges. Hermetically sealed options are available upon request.
-
Product
Multifunction Electrical Installation Meter
AMPI-520
-
The AMPI-520 digital meter is designed to measure impedance in short-circuit loops without tripping the differential protection, it also measures the protection tare, earth resistance, continuity and phase sequence check.
-
Product
Prepayment Meters
-
Shenzhen Star Instrument Co., Ltd.
Star Instrument single-phase and three-phase prepayment meters.
-
Product
Phase Detector Modulevalon
4002
-
sThe Valon 4002 Phase Detector module Independently measures both Gain/Loss and Phase between two signals. It is a perfect complement to all our Frequency Synthesizer modules and ideal for many experimental RF applications. The 4002 enhances the performance of the AD8302 base core.
-
Product
AC/DC TRMS Insulation Clamp Meter
CMi210
-
A unique insulation clamp meter for the installation, testing and maintenance of domestic and industrial installations. This high specification clamp meter can perform insulation tests to 6G Ohms with 5 test voltages from 50V to 1000V.
The clamp provides True RMS measurement of AC current to 1500A and AC voltage to 750V. It will also measure DC current to 2000A and DC voltage to 1000V. The CMi210 has all the same test functions you would expect to find on a high specification multimeter with the added benefit of temperature measurement.
-
Product
Power Meters andCalibration Cells
-
The Solar Reference Cell consist of a 20 x 20 mm monocrystalline silicon Photovoltaic Cell encased in a 92 x 70 x 16 mm metal enclosure with a protective quartz window and a temperature sensor. The temperature sensor is a 100 ohm platinum Resistance Temperature Detector (RTD).The Solar Reference Cells come with a Certificate of Calibration and compatible set of connecting cables. The following parameters of the reference cell are certified: Isc, Imax, Voc, Vmax, Pmax, Area, Fill Factor and Efficiency. The certification is accredited by NIST to the ISO-17025 standard and is traceable both to the National Renewable Energy Laboratory (NREL), and to the International System of Units (SI). A compatible cable set is also supplied with each Solar Reference Cell.
-
-
Product
Heat Flow Meter
-
Thermal conductivity is a measurement of a materials ability to conduct heat and can be critical for evaluating energy efficiency and thermal performance of materials. The HFM-100 Heat Flow Meter is designed as an easy-to-use method for the measurement of thermal conductivity and thermal resistance of insulation products, construction materials, packaging, and assemblies. Available at an exceptional value, the Thermtest HFM has been engineered for industry-leading performance by combining the highest accuracy, repeatability, and widest temperature range possible, and follows international standards: ASTM C518, ISO 8301, and EN 12667.
-
Product
Electricity Metering Device- Residential
ES-10B
-
Designed for the residential smart meter rollout in Great Britain, this 4 terminal single phase electricity meter is the second generation version within our SMETS2 compliant solution.Taking learnings from the first generation meter, the ES-10B is a more refined SMETS2 compliant electricity meter with 100A main disconnect relay, dedicated secure microcontroller and with multiple interfaces including Zigbee and DLMS.
-
Product
Three Axis Accelerometers
TAA
-
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
Product
Dew Point Meter
NOVOTEST KTR-1
-
Dew Point Meter NOVOTEST KTR-1 is designed for rapid non-destructive measurement the temperature, humidity, dew point calculation and measurement of the surface temperature by contact method.
-
Product
Phase Stable Cables
FlatPhase 100 Series
-
Best in class phase stability vs. temperature makes FlatPhase™ the preferred option when you need flat phase.Our proprietary foamed fluoropolymer dielectric avoids the typical PTFE knee to deliver a flatter phase response.
-
Product
Rotating Torque Meter
NTS-6 series (S1/S2/S5/S10/S20)
-
Torque measurement of rotating body. Measure rotational torque during assembly of devices with rotating functions and on finished products. While the output shaft self-rotates, the built-in sensor catches load fluctuations on the rotating body. It is possible to measure the rotation starting torque of the rotating object ( which does not rotate by itself and does not have power) and the load torque during rotation. (Printers, copiers, zoom lenses, door knob mechanisms, hinge mechanisms, etc...)
-
Product
Phase Monitors
-
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
Product
Keypad Meters (STS)
-
Shenzhen Star Instrument Co., Ltd.
Star Instrument single-phase and three-phase keypad energy meters.
-
Product
Digital Sound Level Meter
Model KM 926
-
Kusam Electrical Industries Limited
KM 926 designed according to the IEC 651 TYPE 2 & ANSI S1.4 TYPE 2 for sound level meter. Instantaneous sound measure function. Measurement Range : 30 ~ 130decibel. With two equivalent weighed sound pressure levels, A & C. Fast & Slow dynamic characteristic modes. AC & DC signed output for frequency analyzer level recorder, FFT analyzer, graphic recorder etc.
-
Product
Ion 700 Benchtop Meters
-
Oakton benchtop 700-series meters are designed for use in crowded laboratory settings. Compact footprint of less that 6" x 7" (16 x 18 cm) conserves valuable space, while the large, dual-display LCD provides excellent visibility—even from a distance. Ion 700 meter measures pH, mV, relative mV, ion concentration and temperature. Automatic temperature compensation (ATC) maintains reading accuracy even with fluctuating temperatures. Models feature five-point pH calibration with automatic buffer recognition for both USA (pH 1.68, 4.01, 7.00, 10.01, 12.45) and NIST (pH 1.68, 4.01, 6.86, 9.18, 12.45) pH buffers. Meters additionally feature ion concentration calibration of up to 5 points. Meter features include Auto-Hold, selectable °F or °C measurement, and easy recall of electrode slope or offset. The convenient pull-out quick reference card keeps procedures handy at all times. Use 700-series meters with any pH, ORP, or ISE electrodes with a BNC connector.
-
Product
Optical Laser Source & Power Meter
-
Shanghai Grandway Telecom Tech. Co., Ltd
Grandway provide a variety of optical network testing instruments to play a stable performance in the process of optical network construction and maintenance.
