Temperature Chambers
Life test cycling of temperature accelerating electronic degradation.
See Also: Environmental Chambers, Chambers, Humidity Chambers
-
Product
Refrigerator Type Constant Temperature And Humidity Chamber
THC Series
-
Optimal chamber for testing materials with mechanical properties sensitive to temperature and humidity effects, such as fibers, paper, or films. Temperature regulation: Automatic control by heater and refrigerator.
-
Product
NI-9213, 16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module
785185-02
Temperature Input Module
16-Channel, 75 S/s Aggregate, ±78 mV C Series Temperature Input Module - The NI‑9213 is a high-density thermocouple input module that is designed for higher channel count systems. With this module, you can add thermocouples to mixed-signal test systems without taking up too many slots. The NI‑9213 includes anti-aliasing filters, open-thermocouple detection, and cold-junction compensation for high-accuracy thermocouple measurements. The NI‑9213 features NIST‑traceable calibration and a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range.
-
Product
Platinum Chambers
-
The Platinum series are top quality temperature/humidity chambers in four larger sizes than our popular Platinous and Global-N lines. More powerful heating and cooling systems on these models ensure prompt response, even with larger and heavier loads. Change rates up to 12°C/m or more is possible, depending on the model.
-
Product
Near-field Chambers
-
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
Product
Temperature Module
U1586B
Temperature Input Module
The U1586B temperature adapter expands the capabilites of your handheld oscilloscope or handheld digital multimeter to measure temperature, either in °C of °F. To be used with a K-type bead thermocouple, and with approximately 1600 hours battery life with an alkaline battery, this adapter ensures you get the most out of your handheld scope or DMM purchase.
-
Product
Temperature and Humidity Chambers
-
Weice Testing Instrument Co.,Ltd.
These chambers are manufactured and designed to meet the high quality requirements and standards, such as UL1581 and IEC60598. They are able to perform under extreme conditions, variable temperature and humid environmentals ensuring high performance testing and superior quality of products.
-
Product
Temperature Chamber
-
HIACC Engineering & Services Pvt. Ltd.
Optimised heating & cooling system offers higher performance & energy efficiency. The test chamber can be customised suiting to different test standards. It comes with larger viewing window, ports for live specimen testing, visual alarm system, improved mobility and smaller footprint.
-
Product
Bench Top Temperature Environmental Chamber
-
Burnsco Environmental Test Chambers
Our compact bench top chamber is ideal for prototype testing, life testing, and quality and durability testing . Its small footprint and comparatively large volume make it ideal in labs where space is a premium.
-
Product
Temperature Sensors
-
Vishay is the only supplier that manufactures both ceramic technology-based thermistors as well as thin film-based RTDs. That means customers have the widest choice of NTC and PTC thermistors along with TFPT and PTS RTD sensors for maximum sensitivity, stability, and accuracy in temperature sensing applications.
-
Product
Environmental/Stability Chambers
-
Canden offers unique- Dual environment chamber-This model allows users to set different temperature, humidity setting in 2 sections with in the same chamber divided by a common wall.
-
Product
Antenna Test Chamber
-
Comtest provides Antenna test ranges fully covered with microwave absorbers for both near-field and far-field measurements. Because we always strive for new solutions, our R&D department developed our ‘Javelin Tip’ polystyrene absorbers. The enhanced material composition and altered shape, lead to improved performance and cleaner working space, enabling you to make high precision antenna testing fast, reliable, and worry-free.
-
Product
Environmental Chamber
-
Qualitest Environmental Chambers are capable of simulating a wide range of temperature, humidity, and other environmental conditions. These environmental chambers are well-suited for use in electronic, military, and pharmaceutical quality assurance and reliability testing, as well as research testing and production processes.
-
Product
Temperature Recorder
G0841MW
-
Complete solution for temperature record during the transport.
-
Product
Insect Rearing Chambers
-
Chamber uses thermoelectric assembly for heating and cooling. This type of cooling/heating system completely eliminates need for conventional refrigeration system and failures due to mechanical components such as compressors thereby drastically increasing the life expectancy of each chamber.
-
Product
Medium-size Reverberation Chamber
E-Series
-
The E medium-size multicavity Reverberation Chamber Series represents that state-of-the-art in reverberation chamber technology. The E-Series can make single measurements, batch tests, protocols or campaign tests for different frequency bands, different technologies and different channel models, running overnight without human intervention.
-
Product
Benchtop Temperature And Humidity Environmental Test chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Benchtop Temperature and Humidity Test Chamber provides a compact footprint and multi-function test performance. It is very popular for labs and product manufacturers to test various small electronic product, electronic components and materials with simulating temperature and humidity environment condition.
-
Product
Humidity and Temperature
Humidity and Temperature Data Logger DL-200
-
Non destructive testing / Humidity and Temperature
-
Product
Vertical Flammability Chamber
TF312
-
TESTEX Testing Equipment Systems Ltd.
Comprises a draft free stainless steel flammability chamber with observation window for easy test viewing. Specimen holders, burner and associated hardware are dependent on the test standard and must be specified.
-
Product
Aquatic Chamber
6800-18
-
The 6800-18 Aquatic Chamber is used to measure steady-state carbon assimilation and chlorophyll a fluorescence from algal suspensions, coral, macro algae, and sea grasses using the LI-6800 Portable Photosynthesis System, the preferred photosynthesis system for terrestrial plant research.
-
Product
Walk in chamber for Complex Salt Spray Test (Temperature controllable)
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
Product
Test Chambers
-
The left-hand axis scales the level of the 100 measurements and the right-hand axis displays the uncertainty to a statistical confidence level of 95%; proving the repeatability is better than +/-0.25dB between the measured values. Guaranteeing repeatability, accuracy and correlation across Lab’s, across Production lines and across the World
-
Product
Thermal Shock Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Three zone thermal shock chamber uses the test material structure or composite material to withstand the degree of extreme high temperature and low temperature in a continuous environment in an instant, so as to test the chemical changes or physical damage caused by thermal expansion and contraction in the shortest time.
-
Product
Automotive High Low Temperature Environmental Test Chamber
-
Dongguan City Simplewell Technology Co. Ltd.
*Windscreen deforsting and demising tests for M1 category vehicles;*Windscreen wiper and washer property tests*Cold start tests for M1 category vehicles and engineers*Air conditioning system tests for M1 category vehicles*Property tests for small-size refrigerated trucks*Environmental tests for M1 category vehicles,small-size trucks,special purpose motor vehicles,motorcycles,engineers and components.
-
Product
Salt Spray Chambers
MX-9200
-
LR Environmental Equipment Co. Inc.
A high reliability thermostatic temperature controller maintains the salt solution at a preset controlled temperature in a reservoir within the double wall construction. The salt solution is introduced into the chamber through an atomizing nozzle. The nozzle can be calibrated by us to perform to MIL-STD-19500B, paragraph 40.8 and other specifications. This specification requires that a salt residue be deposited on the specimens, in addition to generating salt fog atmosphere.
-
Product
Compact Humidity Chambers
FW1.5
-
The Bemco FW1.5, mechanically cooled Compact Humidity Chamber, has a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH. This chamber features direct dry air injection and a direct humidity sensor.
-
Product
Modular Walkin Chamber
-
CME’s Modular Walk-In chamber offers unmatchable flexibility in installation. The panelised construction is engineered to perform at demanding testing conditions offering highest reliability and performance. Besides modular construction, we also offer Walk-In chamber made from welded rigid panels.
-
Product
Temperature Logger
TRIL-8
-
The LogTag® Dry Ice “Probe-less” Temperature Logger operates, measures and stores up to 8000 temperature readings in temperature environments ranging from -80°C to +40°C (-112°F to +104°F).
-
Product
Cytogenetic Drying Chamber
CDS-5
-
Developed in cooperation with Mayo Clinic, Thermotron's Cytogenetic Drying Chamberthe CDS-5was specifically designed for conducting cytogenetic slide drying tests during harvest of in situ and non-in situ grown cultures. The CDS-5 provides the optimum controlled temperature and humidity environment required to achieve ideal chromosome spreading results. As evidenced in research conducted by the Cytogenetics Laboratory at Mayo Clinic, the CDS-5 facilitates reliable and repeatable chromosome spreading. The use of an environmentally controlled drying chamber is a practical and cost effective way of achieving ideal chromosome spreading in a routine and highly consistent manner. Favorable chromosome spreading results can be obtained for both in situ and non-in situ cultures including PHA stimulated lymphocytes, bone marrow, amniocytes, and fibroblast.
-
Product
Vibration Test Chambers
-
Our vibration test chambers offer a variety of solutions for vibration testing. AV-Series and CV-Series vibration chambers offer rapid temperature change rates with combined temperature, humidity, and/or vibration environments. These chambers are designed for compatibility with your choice of electrodynamic or mechanical vibration systems. The Benchtop Vibration Table, ideal for vibration testing of small components or electronics and is designed for stand-alone testing or may be placed in an environmental chamber for combined temperature and vibration testing. HALT/HASS Test Chambers provide extreme vibration and temperature capabilities in order to identify design and product weaknesses.
-
Product
Condensation Chamber
-
Wewon Environmental Chambers Co, Ltd.
The condensation test chamber does not need special installation conditions, just need to connect to the ordinary power supply and running water can be used normally. The functional diversity of the equipment, fast and low operating costs make the machine a very high cost performance condensation testing machine in the market. The machine can be programmed to control three different test effects: Humidification, natural cooling and drying, and the corresponding temperature and running time of each test, and set the total time of program running and the number of cycles. The condensation tester has an automatic water replenishing device. When the water temperature exceeds the upper limit, there will be a protection device for safety warning, and it is very safe to use.https://www.wewontech.com/condensation-chamber/
