-
product
IVN-8561, Automotive Ethernet Interface Device
786169-01
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
product
Cable Management Tools and Testers
For anything compture repair and workstation installation tool, you've come to the right place. C2G carries a variety of cable tools and testers for network, coaxial, electrical, F-type, PC, telephone, and fiber cables. Our crimp tools are also available for RCA, BNC, F-type, RJ45, RJ11, RJ12, and flat ribbon connectors. C2G cable cutting tools can be used to cut a range of wiring types, from RG6 and RG59 coax, speaker wire, UTP network cable, flat ribbon, and more.
-
product
UTP Cable Tester
21-8574-00
The Lan Cable Tester is consists of unshield RJ45:568A, 568B & USOC. The tester also easy to operate, the user begins testing by connecting. The multiple LEDs showed indication. This Lan Cable Tester is very practical tester can be easily read and correct pin configuration of cable continuity, open, short, miswiring, & no connection.
-
product
Ethernet Media Switch
Ethernet media switch is a layer 2 switch running on Ethernet or Fast Ethernet. It equips with one or two fiber ports and four copper UTP ports and hence acts as easy-to-use add-drop equipment for connecting network devices into optical fiber network. Ethernet media switch meets corresponding IEEE 802.3 standards.
-
product
Coupling Decoupling Network for Communication Lines
CDN61000-5C
• Application Range: ≤4kV, 1.2/50us pulse, 8 wire unshielded twisted pair (UTP) • Test Voltage: Max 4KV, 2 kV (1.2/50 µs pulse when RJ45 connector is connected. Maximum test voltage is 1.5kV when RJ45 female is unconnected or auxiliary terminal is not protected.) • Coupling mode: 90V gas- discharge tube+250ohm Resistor/Each Wire, 8 Wires Simultaneously-Ground (Common Mode) • Input and output interface: RJ45 connector • Terminal layout (RJ45 connector): First pair of lines: pins 1/2 Second pair of lines: pins3/6 Third pair of lines: pins 4/5 Fourth pair of lines: pins 7/8 • Max. operating speed: 1000MBit/s • Max operating voltage: Max 50V DC • Max operating current: Max 1A Related Instruments
-
product
Smoke Detection Sensor - UL Approved
ENVIROMUX-SDS
For warning of smoke. Photoelectric smoke detector. Smoke sensitivity: 0.98-2.4%/ft. Built-in 135° F (57° C) thermal heat sensor. Includes mounting hardware. Connect to RJ45 or digital input sensor ports. Supports CAT5/5e/6 UTP or STP cables. Screw terminal. To connect to the RJ45 inputs use CAT5/5e/6 cable terminated at one end with RJ45 connector. Connect the un-terminated end to the sensor screw terminal. Operating temperature: 14 to 122°F (-10 to 50°C). Maximum cable length: 1,000 ft (305 m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: UL, RoHS.
-
product
Ethernet Media Converter
A physical layer equipment which interconnects the Ethernet, Fast Ethernet, or Gigabit Ethernet on copper UTP and the related fiber optics network. Ethernet media converter meets corresponding IEEE 802.3 standards.
-
product
4x4 VGA + Audio Matrix Switch with UTP Output and IP Control
VSM-I-A-4-JA4
Switch up to 4 VGA inputs to 4 VGA outputs with independent audio routing. Additional RJ45 output connectors provide extended output up to 1000 ft (305 m) over a single UTP cable (with compatible URA receivers). 550 MHz bandwidth supports resolutions beyond 1920x1200.
-
product
CAT-5 Cable Equalizers
Analog Devices high speed, differential receivers and CAT-5 cable equalizers compensate for the transmission losses of UTP and coaxial cables up to 300 meters in length. Our design techniques for products such as the AD8123 optimize performance for low noise, short-to-medium range applications, while also providing the high gain bandwidth required for long cable equalizations. Various gain stages are summed together to best approximate the inverse frequency response of the cable. Logic circuitry controls the gain functions of the individual stages so that the lowest noise can be achieved at short-to-medium cable lengths.
