Battery Load Testers
determine the condition of batteries to provide power.
See Also: Battery Capacity Testers
-
Product
Electronic Loads
-
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
Product
Dummy Load
-
Dummy load is capable of dissipating four times the legal limit 6 kW for 2 minutes and legal limit 1500 watts key down, forever. It covers the 160 meter to 6 meter bands (actually 1 Mhz-60 MHz continuously). It is a dry dummy load intended for testing amplifiers and station conditions. Two fans on the rear of the unit are automatically turned on when the internal temperature reaches 120°F/49°C . The unit runs off a universal AC supply. Simple to operate and use, the dummy load includes an RF sample output of -60 dBc.
-
Product
Spring Testers
-
Imada offers manual or motorized spring testers in vertical or horizontal configurations.Lever-operated manual systems enable rapid compression and tension spring testing.Wheel-operated manual systems enable slower, more precise movement with the hand wheel.Motorized compression testers offer the most control and highest degree of repeatability with the ability to set a constant test speed and range of movement.All spring testers can be configured with a digital force gauge with data output for analysis by data acquisition software. An optional digital distance meter to measure displacement is available.
-
Product
ContactLAB Tester
-
The ContactLAB test platform provides fully configurable reader signal emulation for validation of ISO 7816 contact smart cards and Single Wire Protocol (SWP) USIM for NFC enabled mobile handsets.
-
Product
All-In-One Battery Testing System
-
Integrating charge-discharge and temperature testing into one.
-
Product
Ethernet Tester
GAOTek Gigabit
-
GAOTek Gigabit Ethernet Tester is a handheld tester for installation, commissioning and maintenance of 10M/100M/1000M ethernet networks. By combining network performance test & monitoring, data packet sniffing, traffic generation, cable test and BER test in one unit. It is widely used in testing BER of layer 1, layer 2, layer 3, and full-featured RFC-2544 and Y.1564 testing. It can help the front-line field technicians analyze the network quality and locate the fault rapidly.
-
-
Product
Voltage Testers
-
Electrical Receptacle Tester Instantly Displays Wiring Condition of Any Standard 3-Wire AC 110-120 OutletNeon Indicators Give Positive Indication of Current StatusCompact Unit Simply Plugs into any Standard 3 Wire/Grounded Receptacle (110–125 Volt AC Circuits)Tests for 6 Circuit Conditions: Open Ground, Open Neutral, Open Hot, Hot/Ground Reverse, Hot/Neutral Reverse & Correct WiringBlister PackedcULus ListedOrder Qty of 1 = 1 Piece
-
Product
6/12 Volt Heavy-Duty Variable Carbon Pile Load Tester
6036B
-
• High-volume testing and fleet use• Tests 6/12 Volt batteries• 1000 Amp load; tests batteries up to 2000 cold cranking amps• Cools with high RPM fan for continuous battery testing• High resolution carbon pile assembly for smoother operation and longer life• Optional Model 6038C for added mobility with convenient heavy-duty cart with wheels• Made in USA of US and Global Components
-
Product
Single-functional testers
3110
-
The MI 3110 EurotestIM is a perfect tool for testing of permanent integrated or portable Low Voltage Electrical Installa-tions supplied by Generator or Transformer and protected by an IT earthing system. Designed for simple but efficient safety testing of Integrated IT Earthing System powered with LV Generator or Transformer! With a single, pre-programmed AUTO SEQUENCE® with sub-tests and adjustable limits it is possible to perform all the necessary verifications of safety limits of a specific LV IT installation.
-
Product
Wiring Tester
WIZE
-
The testers can be used both in production and maintenance, as WIZE® is suitable for simple wiring tests and complex interconnect tests for full systems. WIZE®’s specifications make it compatible with the standard requirements used for testing in the aeronautics, space, rail and defence sectors or any other industry using wiring.
-
Product
BIP Tester
-
BIP TESTER is a measuring device designed for users that already have a unit injector test bench, but their lack reliable BIP measurement.
-
Product
AC Loads
-
During AC electronic load tests, loads are simulated to confirm that a power device or system can operate properly, according to its capacity rating. This type of resistive load testing can often pinpoint power system issues in time for preventive maintenance to be performed. AC load tests can also evaluate the capacity of your essential batteries. Our loads are built to help you reduce downtime, power disruptions and risks to systems. They are valued in utility, transportation, data center, industrial manufacturing and communications environments. Our portable AC load products from Eagle Eye Power Solutions withstands harsh field testing conditions. The AC Load Banks from Eagle Eye are designed to test generator sets, UPS units, power inverters and other AC sources of power. Transcat also stocks devices that flexibly support both AC and DC load applications.
-
Product
Battery Testing
BTS 200
-
This testing and maintaining battery system allows to perform measurement of battery voltage, discharging current test and testing of battery capacity. BTS 200 can be connected with external load unit ELU 200.
-
-
Product
GAS Testers
-
Shenzhen Noyafa Electronic CO.,LTD
Noyafa GAS Tester uses high-quality semiconductor sensors, which can effectively eliminate interference and accurately obtain the concentration of formaldehyde, TVOC, etc. within the measurement range, accurate to the thousandth. With more than ten years of professional testing background, well-known big brands are more at ease and assured to use.
-
Product
Compression Tester
-
Guangzhou Biaoji Packaging Equipment Co., Ltd.
Compression tester is used to test the compression resistance of packaging bag.
-
Product
Smart Load Manager
-
Nippen Electrical Instruments Co.
This is flush mounting micro controller based instrument with multilayer PCB having SMT components offering accuracy and reliability along with reduction in EMI and EMC interference. These are specially designed to simultaneously measure, display and communicate several electrical parameters. This meter is an Ideal data source for effective Energy management, SCADA, PLC, BMS etc to measure as many as 36 parameters on 23 display pages, which are true RMS. The readings are displayed on 3 line bright Red 7 segment LED, each row/ line having 4 14.2mm high LEDS.
-
Product
Shock Test System, Battery Test
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's shock test system used to measure and determine the impact resistance of a product or package. It is mainly used to evaluate the reliability of the function and the integrity of the structure of the test product under impact environment. Suitable for impact testing of aerospace, aerospace, marine, military, consumer electronics, automotive, household appliances and display equipment.
-
Product
CTEK PRO Battery Tester
40-209)
-
Complete with an integrated printer, it’s now easier than ever to determine and present the current state of a battery and electrical system with the CTEK PRO Battery Tester. The PRO Battery Tester performs quick, simple, and accurate battery or system testsin seconds without heat, sparks, or user interpretation. The results can then be printed and reviewed immediately with customers for added impact to preventative maintenance routines and customer service. The CTEK PRO Battery Tester is patented and features a 2-year warranty.
-
-
Product
Rotor Tester
SL Series
-
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing fully opened, fully closed squirrl-cage rotors with process slot, with or without shaft, it can identify broken bars, slim bars, under-casting, porosity, sand holes, residues, improper end rings, internal short circut in bars, eccentricity.
-
Product
Insulation Testers
-
PeakTech Prüf- und Messtechnik GmbH
This digital insulation measuring device is required for various measurements of cables, components and their insulation. The voltage required for the insulation measurement can be set using the rotary switch. By pressing the test button, the set voltage is output and the device / line to be measured is checked. In order to carry out a measurement permanently without having to hold the button down, the test button can be turned while pressing it. For the insulation measurement function, three voltage values can be selected to cover a wide range of test types.
-
Product
Car Battery Analyzer
TE6-0602
-
Hangzhou Tonny Electric & Tools Co., Ltd.
For DC12V car battery test. Plugs conveniently into any vehicle cigarette lighter socket, Measure remaining power, Compact and easy to store, Easy to read light meter
-
Product
HDMI Tester
21-8575-00
-
The HDMI Tester is designed to provide fast convenient verification of proper pin connections of HDMI cables and wall plates. The set includes a Main Test Unit and Remote Test Receiver.
-
Product
Capacitor Tester
MIG0603CAP
-
The MIG0603CAP consists of two circuits with impulse capacitance 20 µF and 0,25 µF. Both circuits generate a voltage wave shape 1,2/50 µs and are combined in a 4 unit height 19" rack. The generator circuits are defined in IEC 60384-14 and EN 132400. The serial resistors Rs, the impulse capacitor CT, and the load capacitance Cp will be automatically switched when different capacitance ranges are selected on the MIG0603CAP.
-
Product
Circuit Testers
-
The circuit breaker finder pinpoints the specific breaker powering the circuit being worked on. Eliminates guessing and unwanted power outages caused by tripping the wrong breaker.
-
Product
Battery Management Systems Testing
System
A Battery Management System (BMS) is an embedded unit performing critical battery functions, including cell monitoring and balancing, pack charge and discharge control, safety, and communications. The BMS must be tested early in development to optimize control algorithms, as well as during manufacturing to ensure reliable functionality. Bloomy’s family of BMS test systems provides a consistent platform for engineers to bring a BMS to market faster, and more reliably.
-
Product
Battery Test Chambers
-
At Weiss Technik we supply battery test chambers specific to testing batteries in a variety of conditions including low or high temperatures, humidity changes, vibration changes, and altitude changes. Our battery test chambers are designed to test Lithium Ion batteries, lead acid, Battery Managements Systems (BMS), battery packs, modules, battery cells, and more.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
