Microwave Attenuators
Reduce the amplitude of microwaves without distorting waveform.
-
Product
RF Attenuators
-
Home > Products > Test and Measurement > AttenuatorsBird - The RF ExpertsRF AttenuatorsBird manufactures a broad spectrum of devices from 2 W to 4000W. Our resistive product portfolio includes air-cooled, water-cooled, oil-dielectric, convection cooled, and conduction cooled RF attenuators with a wide range of connectors and attenuation values.
-
Product
FieldFox Handheld Microwave Analyzer, 18 GHz
N9917B
Microwave Analyzer
Keysight's FieldFox portable analyzers are equipped to handle your toughest working environments during routine maintenance, in-depth troubleshooting, and anything in between.
-
Product
Fixed Attenuators
-
Macom Technology Solutions Holdings Inc.
MACOM offers fixed attenuator bare die to be used in chip and wire assemblies. These products offer excellent return loss and flat attenuation from DC to 50 GHz. Attenuation values range from 0 to 20 dB.
-
Product
Chip-Type Attenuators
-
Panasonic Industrial Devices Sales Company of America
Chip-Type Attenuators for high-frequency signal attenuation, level adjustment or matching improvement.
-
Product
POWER ATTENUATORS
TYPE ATF
-
National RF’s Type ATF Power Attenuators were designed to allow interfacing of linear power amplifiers to RF exciters, where a specific amount of drive to the amplifier is prescribed. Often, however, drive from the RF exciter exceeds this minimum prescribed level and some form of power attenuation must be used in order to not damage the input of the power amplifier. National RF’s type ATF-3 offers 3 dB of power attenuation (1/2 of the power) when used between the exciter and the amplifier and will handle an input power of 132 Watts, RMS (continuous power) while providing about 66 Watts RMS output power, when it is terminated into 50 ohms. In practice, the ATF-3 attenuator will handle exciters achieving Peak Envelope Power levels (PEP) in the area of 200 to 250 Watts while providing half of that power to the load. For less attenuation requirements, the ATF-1 and ATF-2 offer 1 and 2 dB of attenuation, respectively.
-
Product
Manually Variable Attenuators
-
The JFW 50 Ohm dual rotary attenuator has been a staple tool to RF engineers for over 30 years. Our years of proven quality and performance make our manually variable attenuators right for any RF environment. Whether you are using the rotary attenuator on your RF test bench or mounting it to a panel, the JFW dual rotary attenuator makes adjusting attenuation quick and easy.
-
Product
Programmable Attenuators
-
JFW offers 50 Ohm and 75 Ohm programmable attenuators with either relay or solid-state designs. 50 Ohm Relay Step Attenuators, 50 Ohm Solid-State Step Attenuators (TTL), 50 Ohm Solid-State Step Attenuators (USB), 75 Ohm Relay Step Attenuators, 75 Ohm Solid-State Step Attenuators, Analog Programmable Attenuators, High Power Solid-State Step Attenuators.
-
Product
Variable Attenuator
VAXE
-
The VAXE Variable Attenuators are waveguide components for tunable signal leveling or reflection compensation in waveguide networks. The Attenuators consist of waveguide section with a resistive film evaporated on the mica surface. The Attenuators has 0 ÷30 dB minimum attenuation range. The VAXE Attenuators are available in four waveguide bands between 33 GHz and 170 GHz.
-
Product
Manual Attenuator (Waveguide)
-
RF Lambda’s manual waveguide attenuators are used to control signal levels using a manual control knob. These are commonly used in test setups or systems where an operator is present and there is a need to change signal levels manually.
-
Product
Attenuator
J2140A
-
CharacteristicRatingMaximum Input Level+20dBm3dB Frequency RangeDC ~ 50MHzMaximum VSWR1.3Attenuation Accuracy0.2dB
-
Product
LXI Microwave Multiplexer, SP6T, 12-Bank, 50GHz, 50Ω, SMA-2.4
60-800-612
Microwave Multiplexer
Our 60-800-612 is a 12 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Microwave Multiplexer, Single SP8T, 26.5 GHz, 50 Ω, SMA, Terminated, Failsafe
40-788-041-T
Microwave Multiplexer
The 40-788-041-T (PXI) and 42-788-041-T (PXIe) are single failsafe SP8T 26.5 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-788 range of multiplexers are available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel. Remote versions are also available which can support one or two multiplexers in a dual slot module.
-
Product
Variable Optical Attenuator
CARY-VA3301B
-
The CARY-VA3301B handhold variable optical attenuator is used for continuously variableoptical signal attenuation. Since the variable optical attenuator is used in the laser system for the on-line testing, CARY-VA3301B can be used in the digital system of communicationdevices (such as: PHD, SDH) and also can be used in the CATV system testing.
-
Product
FieldFox Handheld Microwave Analyzer, 9 GHz
N9915A
Microwave Analyzer
9 GHz max frequency Carry the world's most integrated handheld & micro; W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
Variable Optical Attenuator
-
Shenzhen Golight Technology Co.,Ltd
Variable optical attenuator uses high-precision attenuation control components, and combines a selfdeveloped embedded data processing platform and precise calibration process, can be provided with maximum 60dB optical power attenuation and optical power monitoring function. Real-time display of input and output optical power.
-
Product
Attenuator
Attenuator VXI
-
The module consists of three blocks:*attenuation unit;*KU block*switching unit
-
Product
Variable Optical Attenuators
5418
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
-
Product
Attenuators And Pulse Limiters
-
A bidirectional attenuator, i.e. the attenuation and power capability specification is valid for both directions. There is a large variety of applications for this attenuator: The measuring range of a spectrum analyzer can be increased. Any kind of meter can be protected against overload; it can be used to control the linearity of a meter reading. It can minimize measurement uncertainty caused by mismatched impedances. During an EMI receiver calibration an attenuator directly at the pulse generator output is inevitable.
-
Product
Programmable RF Attenuators
-
The AD-USB R3 is AdauraTech’s latest design in the AD-USB series of programmable RF attenuators. Combining all the best features of the previous models, the R3 is the new series flag ship. With a completely custom machine aluminum enclosure, the R3 boasts 95dB of attenuation. The addition of Ethernet allows EASY implementation into the most modern of test setups by allowing network control via HTTP web interface or direct Telnet while the USB port powers the device and allows for serial communication.
-
-
Product
VOA Variable Optical Attenuator
JW8506
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW8506-VOA Variable optical attenuator is JOINWIT specially designed for the current optical transceiver, optical network integration test. It is the test equipment with excellent performance. JW8506-VOA Variable optical attenuator through the design of high density，greatly saves equipment cover space，multi-channel independent optical attenuation provides a higher rate of test date throughput and test，the device also provides several communication interface，can support system integration with Joinwit testers. It is the ideal solution of 40G/100G optical module、optical network、optical attenuation sensitivity in optical transmission field and error rate.
-
Product
Variable Optical Attenuators
5420
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
Optical Variable Attenuator
JW3303
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3303 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, therefore, JW3303 can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV)
-
Product
Variable Optical Attenuator
KI 7010 Series
-
The KI 7010 Series hand held Fiber Optic Variable Attenuator is a precision handheld instrument commonly used for testing optical system margin. Superior specifications, high productivity and remote control capability also make this a genuine laboratory instrument.
-
Product
FieldFox Handheld Microwave Analyzer, 26.5 GHz
N9918B
Microwave Analyzer
A lightweight, durable cable and antenna analyzer, spectrum analyzer, network analyzer, and more.
-
Product
Voltage Control Attenuator
-
Voltage variable attenuator offering infinite attenuation precision and broadband performance
-
Product
Coaxial Dynamics RF Attenuators
-
Coaxial Dynamics RF Attenuators offer a reliable and accurate method for reducing RF power levels. All of our designs dry convection cooled and can be used in any position.
-
Product
Optical Variable Attenuator
TW3303
-
Techwin(China) Industry Co., Ltd
The Perfect Handhold Tester Series Optical Variable Attenuator TW3303 TW3303 handhold optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there, thereforeTW3303 can be used in the digital system of communication devices (such as: PHD, SDH) and also in the system of adopting analog modulation (CATV
-
Product
SMA Rotary Attenuator
WATT-6SR1211
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
