Optical Combs
Frequency comb measuring light frequencies.
-
Product
Mini Fiber Optic, Contact, Receiver, Polymer Optic Fiber
610113170
Fiber Optic Contact (Receiver)
This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113171. (May mate with other ITA contacts, as well.)
-
Product
Reference Radiators / Comb Generators
-
The Spectrum Generator is a family member of the Schwarzbeck pulse generators, which are used as pulsestandard world wide. Whilst the latter one uses a bounce free relay contact to discharge a coaxial lineto the load resistor, it uses a special avalanche transistor instead of the relay contact.
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
Mini Fiber Optic, Contact, ITA, Multimode
610113173
Fiber Optic Contact (ITA)
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113172. (May mate with other Receiver contacts, as well.)
-
Product
Erbium Fiber Frequency Comb
-
Detailed description of item: The AOSense frequency comb is a low noise, polarization maintaining (PM) device. Key features include a PM fiber architecture centered at 1550nm with turnkey modelocking; a free-running linewidth of the carrier-envelope offset frequency of <200 kHz; a temperature-insensitive all-fiber f-2f interferometer exhibiting fceo beatnotes with SNR > 45dB (300kHz RBW); and dual fast/slow cavity length actuators with a bandwidth of >300 kHz. The repetition rate of the comb is factory set and allows matching across multiple combs for dual comb applications. The optics package incorporates an optical heterodyne module designed for locking to the comb to an ITU-specified laser reference. The comb is capable of supporting an Allan deviation of < 5 x 10-18 at 1 second and ~10-20 after 105 seconds. Add-on features include all fiber extensions to visible wavelengths corresponding to several atomic transitions. An integrated comb electronics package is currently under development.
-
Product
Comb Generator
CG118
-
The main application of comb generator is to quickly verify 1GHz above radiated emission and conducted emission test setup.And the most important application is 3m chamber and 10m chamber 1GHz above to18GHz with 250MHz frequency spacing for site validation,shielding efficiency. reference signal source Noise Generators Signal Generators
-
Product
Flatness Mirror
10773A
Optical Module
The Keysight 10773A Flatness Mirror is a 100% reflectance mirror that turns the direction of an incoming laser beam 90 degrees. The mirror, used in the 5530 Laser Calibration System, measures flatness in applications such as surface plate calibration. It can be used in place of the 10707A Beam Bender (6 mm or less beam diameter) for applications that require the larger aperture of the 10773A.
-
Product
Comb Generator
HPR727A
-
The HPR727A Comb Generator provides precise harmonic signals with a fixed and known phase relationship between each tone, making it an ideal tool for time-domain calibrated RF measurements.
-
Product
Comb Generators
-
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
Product
USB Harmonic Comb Injector
J2150A
-
The USB Harmonic Comb Injector is a fast, easy-to-use, ultra-portable signal generator for interrogating your PDN to identify noise sensitivities. Quickly identify power supply related issues. Multiple modes include time and frequency jitter. Wideband harmonic comb spans 1kHz-1GHz+. Great for clock power supply EMI spectrum testing.
-
Product
Fiber Optic Sensors And Fiber Optics
-
Over 350 customized fiber optic solutions. Smaller, more precise, faster. Robust - High-temperature, chemically resistant, mechanically robust glass or plastic fibers. Better performance - Position-independent detection of irregular objects or liquids. Plug & Play - Intuitive parametrization with the Baumer Sensor Suite via IO-Link.
-
Product
Optical Square
10777A
Accessory Kit
The Keysight 10777A Optical Square, used with Keysight straightness measurement optics, adds squareness measurement capability to the Keysight5530 Laser Calibration System. The optical square measures the squareness of axes during laser calibration of a machine tool. The Keysight 10777A uses two accurately-aligned mirrors to direct an output beam at precisely 90 degrees to an input beam.
-
Product
Optical Monitoring
-
Perform OSNR monitoring, valid channel detection, and center wavelength measurement of signals with arbitrary modulation formats.
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended
7-416804000-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Multimode, 62.5/125, Single Ended.
-
Product
Optical Systems
-
Thorlabs' optics can be incorporated together to create packages with new functionalities. Some of the packages highlighted here range from beam expanders and collimators to interferometers and spectroscopy kits. Optical isolators, Pockels cells, and modulators are other examples.
-
Product
Optical Controllers
-
Teilch’s compact DM controller for the Kilo DM is capable of delivering 16bit resolution over 220V and with dynamic range of 1kHz. System is directly integrated with the Zif Socket, eliminating the need for cables and providing a direct mechanical connection from the bench mount to the DM.
-
-
Product
Optical Switches
-
Nanning Xionghua Photonics Technology
Optical Switches by Xionghua Photonics
-
Product
Optical Tensiometers
Theta High Pressure
-
The Attension® Theta High Pressure is a tensiometer for measuring wettability and interfacial tension at high pressures and high temperatures within enhanced oil recovery research. With the harsh conditions of an oil reservoir in mind, the instrument is designed to ensure ease of use and yet offer wide measurement possibilities.
-
Product
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, Single Ended
7-414845000-036
Fiber Optic Patchcord
Mini Fiber Optic, Patchcord, Receiver, 36", Polymer Optic Fiber, Single Ended.
-
Product
Optical Sensors
-
Broadcom offers a wide range of optical sensors solutions including ambient light, RGB color, proximity and gesture sensors for a broad range of applications including:*Mobile / Computing - smart phone, tablet, laptop, gaming mouse, printer*Consumer Electronics – TV displays, handheld game console, digital camera*Lightings – Industrial / commercial lightings, residential lightings, outdoor street lightings*Automotive – Instrument panel illumination*Medical Diagnostic Equipment*Industrial Instrument*Contactless switches*White Goods*Sanitary Products*Health / Fitness Products
-
Product
Active Optics
-
Radiall designs and manufactures end-to-end optical links for massive data transfers in harsh environments.
-
Product
Radiating Comb Generators
TBCG1
-
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
Product
Fiber Optics
-
The use of fiber optics as light guidance allows great modularity and flexibility in the setup of an optical measurement system. Optical fibers can be made of many materials, such as plastic, glass, and silicates (SiO2). For high-quality fibre optics, as used in spectroscopic applications, synthetic fused silica (amorphous silicon dioxide) is used, which can be intentionally doped with trace elements to adjust the optical properties of the glass.
-
Product
Optics And Opto-Mechanics
-
Goniometers, optical rails/benches/stands, lens tubes and light guides.
-
Product
Optical Transmitter
ST1015-10mW
-
Hangzhou Softel Optic Co., Ltd.
*Designed for FTTH(Fiber To The Home) Networks *Excellent Linearity and flatness *Single-mode fiber high return loss *Using GaAs amplifier active devices*Ultra low noise technology *Using DFB coaxial small package laser *Smaller size and easier install *Red-LED for power indication
-
Product
Optical Comparators
-
Starrett optical comparators provide a time tested, cost effective, solution for non-contact measurement. Optical comparators are used for an exceptionally wide range of dimensional inspection applications.
-
Product
Mini Fiber Optic, Contact, Receiver, Multimode
610113172
Fiber Optic Contact (Receiver)
* This contact available for purchase as a patchcord only. Choose link below to configure as a patchcord. Primary mating contact 610113173. (May mate with other ITA contacts, as well.)
-
Product
Optical Transmitter
ST1550E
-
Hangzhou Softel Optic Co., Ltd.
SFT1550E is a high performance external modulation 1550nm Optic transmitter with a high quality LiNbO3 external modulator and a high power, narrow bandwidth, low noise DFB laser. It adopts a series of unique innovation technique to reach the excellent system control. With 47~862Mhz bandwidth, CNR≥53dB, CTB≤-65dB, CSO≤-65dB, SBS: 13, 16, 18adjustable, it can make CA TV network transmit video, audio and data with high performance. The machine can is equipped with perfect RS232 communication interface, SNMP network management and 1+1 backup power supply .
-
Product
Punched Wet Film Combs (Aluminium)
112AL
-
The Elcometer 112AL, being punched from aluminium, is not as accurate as precision formed stainless steel wet film combs and has a shorter lifespan.
