Digital Fault Recorders
record out of limit electrical power system events.
See Also: Fault Recorders, Transient Recorders, Disturbance Recorders
-
Product
PXI-6514, 64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module
778965-01
Digital I/O
64-Channel, ±30 VDC, 32 Sink/Source Inputs, 32 Source Outputs, Bank-Isolated PXI Digital I/O Module—The PXI‑6514 is an industrial digital I/O interface with eight banks of isolated channels. With programmable power-up states, you can configure the initial output states in software to ensure safe operation when connected to industrial actuators. If a computer or application fault occurs, the PXI‑6514 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
16-Ch Source-Type Digital Output EtherCAT Slice IO Module
AMAX-5057SO
Digital I/O Module
Channels:16 (Source Type)Voltage Rating:10~30VDCRated Current Output:0.5A per channel atsignal "1"Leakage Current:10 μA per channel atsignal "0"Output Delay:From logic level 0 to 1:150μs; From logic level 1 to 0: 2ms
-
Product
PXI/PXIe Digital To Analog Module - 4 Channel
43-770-001
Digital / Analog Converter
The 41-770-001 (PXI) and 43-770-001 (PXIe) have four Digital to Analogue Conversion channels in a single PXI/PXIe slot. Each channel is fully isolated and able to supply a programmable voltage or programmable current output. The outputs can work in one of several modes of operation: ±1 V, ±2 V, ±5 V, ±10 V, ±20 V, 0-40 V, ±5 mA, ±10 mA, ±20 mA. Each channel of the 41/43-770 module is able to simulate the open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785171-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
NI-9437, 24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module
783393-02
Digital Module
24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9437 is well suited for direct connection in rail and power applications along with a wide array of industrial and automotive switches, transducers, and devices with high-voltage input needs. It features ratiometric thresholds that automatically adjust to 2/3 of the user supply voltage.
-
Product
640 Gb/s Digital Signal Processor
M8132A
Digital Signal Process
The M8132A is a powerful digital signal processing module featuring two customers accessible Xilinx Ultrascale+ FPGAs, four optical data interfaces (ODI) running at up to 160 Gb/s in+out each, and a PCIe Gen3 x8 link to the AXIe backplane. In addition, the module provides a trigger input and output, synchronization input and outputs for deterministic latency between compatible digitizers and AWG modules as well as a 10-general purpose I/O pins. The M8132A is part of Keysight’s Wideband Solution Platform that consists of a portfolio of compatible instruments, including digitizer, arbitrary waveform generator, digital signal processor and storage modules.
-
Product
Digital Multimeter Device
Digital Multimeter
Digital Multimeters measure voltage, resistance, current, capacitance, inductance, and temperature. Some models also have an isolated digitizer mode. Use these products to test consumer electronics, fuel cells, aerospace production, and more.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 40 MS/s on 24 Channels
DN6.593-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
68-Pin D-SUB Female to 68-Pin D-SUB Female, Twisted Pair, Shielded Digital Cable
183432-0R4
Digital Cable
The SH68F-68F Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
Product
PXIe Digitizer: 4 Channels, 2 GHz, 12-bit
M5200A
Digitizer
The M5200A is a single-slot PXIe four-channel, high-speed, analog to digital digitizer. It is a high-performance digitizer with easy-to-use programming libraries, real-time sequencing technology, and FPGA programming.
-
Product
NI-9437 , 24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module
783737-01
Digital Module
24 VDC to 250 VDC, 8-Channel (Sinking Input), 1 µs C Series Digital Module - The NI‑9437 is well suited for direct connection in rail and power applications along with a wide array of industrial and automotive switches, transducers, and devices with high-voltage input needs. It features ratiometric thresholds that automatically adjust to 2/3 of the user supply voltage.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 24 Channels
DN6.592-24
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
32-Ch High Voltage Relays & Multimeter
YAV90HVT
Digital Multimeter
The YAV90HVT is used as an automatic CAN bus controlled floating AC/DC true RMS digital volts/milliamps meter with built-in scanner, able to work directly in appliances and industrial mains powered electric/electronic equipment.Its powerful microcontroller allows to work as a distributed device able to data acquire, compare and return high level messages, reducing test operation time.The analog output is used as a set value for the optional high voltage programmable power supply for Hipot tests up to 1500V.The board uses Tripaddle connection modules and can operate as stand alone or be mounted on a standard Virginia Panel receiver.The board includes National Instruments LabView virtual control panel and operating software for a true Plug & Play operation.
-
Product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
Digital Multimeter
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit High Speed Digitizer - 250 MS/s on 8 Channels, 8 Single-Ended Inputs
DN2.442-08
Digitizer
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
Digital I/O
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
Product
64-Ch 1-Bus Fault Insertion
YAV91082
Fault Insertion Unit
64 channels 1 thread 2A 250V 1 Fault Insertion Buses Switching up 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
Product
Dynamic Digital I/O with Per Channel Programmable Logic Levels and PMU PXI Card
GX5295
Digital I/O
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 4 Channels (Differential)
M2P.5926-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
NI-6581B, 100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO
783887-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel, Kintex-7 FPGA-Support, Digital I/O Adapter Module for FlexRIO—The NI-6581B is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. A digital I/O adapter module for FlexRIO can be used to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581B can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
Digital I/O Module
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785165-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
Digital I/O
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
Ethernet/AFDX/BroadR-Reach PXI Fault Insertion Switch - 4 Channel
40-201-004
Fault Insertion Unit
This high bandwidth differential fault insertion module is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This module supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, BroadR-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
Product
68-Pin D-SUB Female to 68-Pin D-SUB Female, Twisted Pair, Shielded Digital Cable
183432-05
Digital Cable
68-Pin, Female D-SUB to 68-Pin, Female D-SUB, Twisted Pair, Shielded Digital Cable - The SH68-68-D1 Digital Cable connects NI 6533/4 digital instruments and NI 660x or 661x counter/timer modules to 68-pin accessories. This shielded cable features twisted pairing and is offered in different lengths.
-
Product
Digital and Analog I/O's
Digital I/O
6TL's line of YAV module digital and analog I/O equipment.
-
Product
PCI-4065, 6½-Digit, ±300 V, PCI Digital Multimeter Device
779770-01
Digital Multimeter
The PCI‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
Product
Handheld Digital Multimeter, 4.5 Digit, Water and Dust Resistant
U1273A
Digital Multimeter
Organic LED (OLED) display for high brightness level and wider viewing angles (up to 160 degrees)Features set that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.6% for ACV accuracy)Intelligent features to improve productivity and safety (LPF, ZLOW, Smart )Better grip Visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 10,000) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
Product
PXI-6508, 96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module
777598-01
Digital I/O
96-Channel, 5 V TTL/CMOS, 2.5 mA PXI Digital I/O Module—The PXI‑6508 uses four, 24‑bit programmable peripheral interfaces (PPIs) that can each be divided into three, 8‑bit ports. The PXI‑6508 can interface to peripherals or other computers, and it can operate in either a unidirectional or bidirectional mode and handshake with peripheral equipment. The PXI‑6508 is well suited for applications that require onboard pull-up resistors.
-
Product
VXI Digital Multimeters
Digital Multimeter
Maximize the use of your legacy test systems with our line of high-performance VXI digital multimeters.
