Programmable Attenuators
-
Product
PXI High Density Precision Resistor Module, 4-Channel, 3Ω to 52.4kΩ
40-298-133
Programmable Resistor Modules
The 40-298-133 is a high density programmable resistor module with 4 channels which can be set between 3Ω and 52.4kΩ with 1Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 1.02k Ohm
40-294-021
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 3.55kΩ
50-298-123
Programmable Resistor Modules
The 50-298-123 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-350-HI
Programmable Resistor Module
The 40-230-350-HI (PXI) and 42-230-350-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 1.5MΩ with 0.125Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-126
Programmable Resistor Modules
The 40-297A-126 (PXI) and the 42-297A-126 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 26.7 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Programmable FPGA Card
CP-FPGA-2
-
Concurrent Real-Time’s family of programmable FPGA PCIe cards feature a powerful field programmable gate array that supports both digital and analog I/O. The cards can control up to 96 digital I/O signals along with 16 analog inputs and 16 analog outputs. Each card’s I/O functionality is fully customizable by the user by means of the FPGA Workbench tools.
-
Product
Variable Optical Attenuators
5418
-
The FOD 5418, 5419, 5420 Variable Optical Attenuators are designed for singlemode application at 1310 and 1550 nm or multimode application at 850 and 1300 nm. They allow variable attenuation settings in range from 0 to 80 dB with resolution 0.05 dB.
-
Product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
Programmable Resistor Modules
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
PowerSync Programmable Load
PSL-3000
-
Sifos Technologies provides a one-box solution to facilitate testing and analysis of Power Sourcing Equipment (PSE) behaviors including basic compliance to the IEEE 802.3at and 802.3bt specifications. Each PSL-3000 test port is an autonomous and fully isolated instrument offering stimulus and measurement resources for 2-Pair PSE testing. Each test slot can be configured as an autonomous and fully isolated instrument for testing 802.3bt and pre-standard 4-Pair PSE’s from either test port in that slot.
-
Product
Programmable Hi-Pot Tester
DU331/332/333
-
Delta United Instrument Co., Ltd.
Large LCD Display Window for Setups and Test Values Output Frequency 50/60 HZ SelectableAll Initial Default Function Setting scan be Changed Easily to Fit RequirementEasy Manual Driven with Cursor Guiding Operation Mode Battery Backup Function will Recall theTest Parameter Settings before Power offLarge Memory (100 sets) for Setup Steps & ParametersEach Memory offers 9 steps of different Test ParametersTest mode: Single Step, Multiple Steps (Step by Step), Test Circle Number or Continuous Test are Programmable DU333 is designed for Multi-point Scan Test DU331/DU332 can perform Multi - point Test when used with Scan Box DU330
-
Product
Variable Attenuators
-
Wuhan Sunma Technology Co., Ltd.
SunmaFiber offer optical variable attenuator is used for continuously variable optical signal attenuation. As the attenuator is used in the laser system for the on-line testing, there can be used in the digital system of communication devices (such as:PHD, SDH) and also in the system of adopting analog modulation (CATV).
-
Product
Programmable AC Power Source
LSP-500VAC
-
• Applied with the AC-DC-AC inverter technology and digital waveform synthesis & waveform feedback technology, low distortion power; • Applied with entire cycle high-precision measurement technology and high-speed sampling technologies, panel of instrument will directly and accurately displays the power output of the voltage, frequency, current, active power and power factor to achieve the integration of the source table; • Applied with SCM control and measurement technology, high intelligence; • Applied with zero output impedance technology, the output equivalent impedance is almost zero and further improve the stability of power supply; • Applied with isolated floating output technology, the power output and input have good isolation, floating output, conducive to make sure power itself safety and operator’s safety; • Perfect voltage, current anomalies and overheating protection, improve the reliability of power supply; • Applied with power limiting technology to avoid strong interference on the power grid and other electrical equipment, while facilitating reliable operation of the power supply itself; • The input voltage can be option via a toggle switch of panel mains 110V/220V; • The initial phase and end phase of the output voltage waveform can be set {0°-359° (±1°)}; • Measurement process can be programmed to control (1 to 50 memory groups, 1 to 9 steps for each memory group);
-
Product
PCI High Density Potentiometer Card 4-Channel, 12-Bit, 0 To 4k Ohm
50-296A-121-4/12
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Programmable Oscillator Amplifier
Amplifier
Computer Conversions Corporation
The Computer Conversions Corporation POA90-3 is a programmable quadrature oscillator with a built-in power amplifier, capable of driving current loads of up to 200mA. The sinusoidal outputs are 2.5Vrms signals that are phased 90° apart as REF out and REF out +90 (Quadrature), allowing the unit to be used with Synchro, Resolver, LVDT/RVDT, Inductosyn, or similar inductive transducers.
-
Product
Low Power Programmable AC Source
61600 Series
-
Chroma Systems Solutions, Inc.
Power:500VA (61601)1000VA (61602)1500VA (61603)2000VA (61604)4000VA (61605)Voltage range: 0-150V/0-300V/AutoFrequency: 15Hz 1000HzCompact size and weight attributable to advance PWM technologyBuilt-in PFC, provide input power factor over 0.98 (full load)AC+DC output mode for voltage DC offset simulationProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage, current limitOne-key recall for 9 different voltage and frequencyLow output impedance for testing IEC 61000-3-2 ( 61605 )Comprehensive measurement capability, V, Irms, Ipk, Inrush, P, Q, S, PF, CF of current and etc.High output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates ON/OFFAnalog programming interface3 units combined to 3-phase power outputEasy-use software for operation and ON/OFF testOptional GPIB and RS-232C interfaceFull protection: OP,OC,OV and OT protection
-
Product
EMU & Mission Data Programmer
MS 1603
-
The EMU – MIP programming station is used to program, read and erase mission data of Mirage 2000 Aircraft and it has additional feature of programming the Extended Memory Unit. It has 3 EMU Slots (1 Read only) and 5 Slots (1 Read only).
-
Product
High Power Programmable AC Source
-
Chroma Systems Solutions, Inc.
Simulate various AC line input conditions and measurement of critical characteristics for products under test
-
Product
Orange5 Programmer + Full Set Of Adapters
-
Orange5 a programmer for programming memory and microcontroller motorola. The advantage of Orange5 is built macrolanguage to save protocols. It gives the ability to add micro schemes, meeting the requirements of manufacturers’ read and write algorithms.
-
Product
Programmable DC Power Supply
IT6100 Series
-
IT6100 series assure you accurate measurements with 0.1mV/0.1mA high resolution and high accuracy. With high-speed List mode output and voltage rise speed up to 20ms, it can independently edit and perform the default voltage waveform to meet the high-speed test needs. IT6100 series has built-in 5 1/2 digital voltmeter and milliohm meter, which can measure additional signals. IT6100 series supports SCPI communication protocol, GPIB/USB/RS232 interfaces are optional for customers.
-
Product
Programmable DC Power Supply
62000L Series
DC Power Supply
The Chroma 62000L Series Programmable DC power supplies have low noise linear performance and fast transient response. The units have many unique functions that are targeted for overall automated test system integration, automotive power electronics MCU/ECU, power semiconductors, wireless communications, etc. The 62000L Series is a high quality yet cost effective programmable DC Source, designed to meet the stringent requirements of the next generation of power electronics. The GPIB and USB control interfaces come standard with the 62000L Series, no additional purchase required. The 62000L Series can be easily remote controlled via either of these two interfaces. The 62000L weighs less than 2.5 kg, and its case measures 214.6W * 88.6H * 280D mm. Its light weight and compact size makes it easy to handle and stack safely.。
-
Product
Programmable AC and DC Power Source
AFX Series
-
The AFX Series is a family of high power, single, split and three phase, AC, DC and AC+DC output capable Power Sources. Available models range from 6 kVA to 90 kVA with available configurations to 150kVA. Using a modern user interface for ease of use, the AFX Series is cost effective and fully programmable for both basic frequency conversion and advanced AC power line or DC power disturbance test applications.
-
Product
PXI/PXIe High Density Precision Resistor Module, 3-Channel
40-297A-146
Programmable Resistor Modules
The 40-297A-146 (PXI) and the 42-297A-146 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
75-Watt AC/DC Power Supply; Single Output
56KS1
Programmable Power Supply
NAI’s 56KS1 is a 75 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides full-power, single output, at a baseplate temperature of +85° C.
-
Product
3-Phase Programmable AC Source
-
Chroma Systems Solutions, Inc.
Delivers the right solution to simulate all kinds of input condition of UUT to be utilized in R&D and QA, suitable for commercial applications from laboratory testing to mass production
-
Product
DC Bias Attenuators
-
a fixed DC Bias attenuator from Pasternack. This 10dB attenuator is an in-line, resistive PI attenuator pad design. Our coaxial 50 Ohm attenuator is manufactured to precise RF / microwave industry specifications.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 102kΩ
40-251-034
Programmable Resistor Modules
The 40-251-034 is a programmable resistor module with 4 channels which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
SignalHawk I/O Programmable FPGA Card
CP-FPGA-6
-
The SignalHawk I/O FPGA Card (CP-FPGA-6) is a programmable digital I/O solution designed for real-time applications requiring flexible, low-latency signal processing. Built on an Altera Cyclone V FPGA with 301K logic elements, the card provides configurable digital I/O capabilities for simulation, data acquisition, and industrial control environments.
-
Product
Universal Programmers
-
A universal programmer is basically capable of programming anything, it will have a 40-pin or 48-pin ZIF socket and independent pin drivers allowing voltages and signals to be applied to each pin. These programmers are considered low to medium cost and would suit someone working with many different types of devices. Programming houses or larger development companies working with many different memory/logic devices would benefit from the capabilities of this type of programmer, its an all in one solution.
-
Product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm With SPDT
50-293-114
Programmable Resistor Modules
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
