Pyroelectric Sensors
Turn absorbed radiant energy into a current or voltage.
See Also: Thermopile Sensors
-
Product
Photoelectric Sensors
-
Our broad range of photoelectric sensors is aimed at all automation solutions where noncontact object detection can be utilized. The wide variety of different operating principles, models, sizes and specifications means that the best possible sensor can always be found for the relevant application and all conditions that occur in practice can be met.
-
Product
MEMS Optical Sensor Test
-
For optical sensor test Cohu offers a variety of solutions being driven by requirements for tri-temp, parallelism and stimulus spacing. Customized optical stimulus units are integrated into Cohu’s test handling systems. For light detector test, we implement different types of light sources, such as infrared, ambient- and colored light. We offer different solutions for 3D image sensors combining emitter and receiver tests of LiDAR, Time of Flight and Structured Light devices.
-
Product
Hall Effect Sensors
906
-
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
Product
Vehicle Presence Sensor
TrafiCam
-
FLIR TrafiCam is a vehicle presence sensor that combines a CMOS camera and a video detector in a single unit. FLIR TrafiCam detects moving and stationary vehicles at signalized intersections. Via detection outputs, vehicle presence information is transmitted to the traffic controller so that signal timing can be adjusted dynamically. This way, vehicle waiting time at traffic lights is reduced and traffic flows are optimized.
-
Product
Paper-Based Screen-Printed Electrode (Paper-Based SPE Sensor)
ZPE1
-
A paper-based screen-printed electrode (SPE) for electrochemical analysis, biosensor research, and rapid diagnostic applications, offering low-cost fabrication, excellent reproducibility, and convenient disposable use.
-
Product
Temperature Measurement IR Sensors & Detectors
M34
-
A thin-film thermopile in a TO-5 package with an active area of 3.16mm x 0.4mm that offers low noise output.
-
Product
LilyPad Temperature Sensor
-
Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor.
-
Product
MOTUS Stand-Alone Sensor
-
There are numerous ways of measuring Ocean Waves. At Aanderaa, we focus on three measurement types: pressure, acoustic, and motion. In this section, we cover the motion-based sensors in the MOTUS family.MOTUS Directional Wave Sensor is suitable for integration on different buoy types. It is intended for commercial as well as research use. The directional stand-alone Sensor processes wave data and is configurable to directly present parameters and wave spectrum. The sensor can be connected to a SmartGuard using the CANbus-based AiCaP protocol. It can also be connected to a PC or third-party systems through the RS-232 interface.MOTUS Wave Height Sensor is for wave height only. As the MOTUS Directional Sensor, it is suitable for integration on different buoy types. In the sensor, the directional wave parameters are locked. It is possible to open the wave direction parameters with a software license from Aanderaa later if the need changes. MOTUS Lite OEM Sensor is the OEM version of the MOTUS Directional Wave sensor. It is delivered as an electronic board without housing and cables. Please get in touch with the factory for more options and restrictions.
-
Product
Long-distance Separate-amplifier Proximity Sensor
ES Series
-
Long-distance Separate-amplifier Proximity Sensors. Detecting distance twice that of conventional sensors. Detecting distance is easily adjustable. Wide range of sensor head types available. Built-in alarm output. Separate amplifier proximity sensors with twice the detecting distance of self-contained sensors and a range of up to 8-mm (shielded) and up to 70-mm (non-shielded).
-
Product
Printed Electronics & Printed Sensors
-
The first membrane switch was developed and produced in 1978 using printed electronics. Conductive pastes can now also be printed on substrates such as paper, textiles, or metal in addition to polyester. Our functional foils and printed electronics enable compact, and extremely efficient electronic products that are used in every industry. Processing intelligent pastes that have various physical properties enable the production of new and innovative applications in minimized form factors without the use of additional, highly complex electronic components.
-
Product
One-Piece Optical Sensor Head
OP
-
Sciences et Techniques Industrielles de la Lumière
OP series consists of a one-piece optical sensor head for dedicated applications (e.g. long distance).The performance and specifications are dedicated to various applications in the industry.Typically integrated as OEM for measuring 3D shapes, glass thickness, autofocus, OP series fits a wide range of applications.
-
Product
Redox (ORP) Sensors
-
ORP sensors measure the oxidation-reduction potential—the tendency to gain or lose electrons when a solution comes in contact with a chemical substance. ORP measurements are used to ensure that a solution has been completely reduced or oxidized. ORP sensors are often used in tandem with pH sensors, which measure the hydrogen ion activity in a solution.
-
Product
Magnetic Field Sensors
-
Our cylinder sensors for pull rod cylinders can be integrated into many applications. They are mounted with mounting brackets on cylinders with tie rods and DUO rails. The concept is suitable for the most common types of cylinders with any piston diameter. Features: contact-free detection of the piston position, tie rod Ø up to 17 mm, reliable switching behavior, wear-free, resistant to dirt, secure grip, easy installation.
-
Product
Photodiode Energy Sensors
-
Our photodiode laser energy sensors are able to measure low energy pulses down to 10 pJ at frequencies up to 20 kHz. Silicon photodiodes for the UV and visible spectrum and Germanium photodiodes for infrared.
-
Product
Clamp type AC Current Sensor／for Power Monitor
ZCT-40P
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC 0.1A～500A*Current measurements of feeder
-
Product
Broadband Sensors
-
Offers a response between 120 sec and 160 Hz in a smaller, rugged, low power and low cost system that is easy to install and deploy. Built with ease of installation in mind, it does not require mass lock, mass centering, and has a large operational tilt range which combines to reduce installation training, time, and cost.
-
Product
Electrodes, Sensors And Measurement Cells
-
Our electrodes are used for important tasks in worldwide laboratories with high demands. What began back then with the patent for pH electrodes now includes a range of several hundred different sensors: whether ultra-pure water, jam, wine, creams or drinking water – we offer the right electrode for every conceivable application. Our extensive electrode program is as diverse as the applications.
-
Product
Vacuum Sensor, Thermocouple Vacuum Gauge for Rough Vacuum
DV-4 Series
-
Teledyne Hastings, manufacturer of the original DV-4, DV-5, and DV-6 thermocouple vacuum gauge tubes, produces vacuum measurement equipment with exceptional stability, accuracy, and reliability under the most demanding conditions.
-
-
Product
Miniature Pressure Sensor
Series 2 Mi
-
KELLER AG für Druckmesstechnik
Developed for measuring hydrodynamic and aerodynamic pressures. A silicone drum protects the measurement cell from the influence of vibrations and fast acceleration.
-
Product
Sensor Evaluation Kits
-
Panasonic Industrial Devices Sales Company of America
Accelerate prototyping and testing by utilizing Panasonic's Sensor Evaluation Kits for all your design needs. Discover today why Panasonic Sensors are the premier choice for creating unique IoT solutions.
-
-
Product
Radar・Sensor Simulation Framework
COSMOsim
-
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
Product
Dual Display Digital Pressure Sensor [For Gas]
DP-100L
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s compact DP-100L Pressure Sensor with IO-Link features an improved digital display that offers increased clarity and a wider viewing angle. Thanks to a redesign of its circuitry, the low-power-consumption DP-100L Series requires 14% less power during normal operation and when operating in ECO / FULL mode the display is completely shut off for an increased power savings of up to 50% compared to normal operation. The current value and the threshold value can be checked at the same time, so the threshold value can be set and checked smoothly without switching to another screen mode.
-
Product
Fiber Optic Sensors
-
Achieve highly reliable and precise fiber optic sensing. Advanced Energy’s Luxtron® patented FluorOptic® temperature measurement solutions and WaveCaptureTM Fiber Bragg Grating (FBG) sensing solutions feature many options to meet your application needs.
-
Product
Distance Sensors
SR50A-L
-
The SR50A is a rugged acoustic sensor for measuring the distance from the sensor to a target. It is typically used to measure snow or water depth, but it is well-suited for other uses.
-
Product
Temperature Sensors
-
The infrared sensor measures temperature at a distance without contacting the target. The integrated infrared module senses the thermal radiation emitted by objects on a 16 x 4 array of sensing points, for measuring the temperature distribution across a surface. These 64 measurement pixels are transmitted via CAN to the host controller or data logging device. The sensor is available in both 35 and 60 field of view options to suit a variety of installations. A software package is provided for viewing live temperature data from the array.
-
Product
Hyperspectral Imaging Sensors
-
HYPERSPEC® sensors are line-scanning instruments (sometimes called pushbroom) that collect reflected light through an image slit. One row of spatial pixels is collected per frame as motion occurs, with each pixel containing full spectral data. Motion can be accomplished in two ways: either as an airborne deployment (UAV, aircraft, or satellite) or stationary (where motion is accomplished beneath the sensor, such as a food inspection line). A third option is also available where pan-and-tilt or rotary stages allow a fixed-location sensor to scan a stationary object (such as a piece of artwork, or a mine face for geological applications).
-
Product
CAN Sensor/ Interface
Current
-
Reach Technologies’ CAN Current Sensors sense and digitize conductor current for collection via CAN. The module is ideal for conveniently adding current data to a distributed CAN network. The CAN Current Sensor is configurable via J1939 or CANopen stacks, and are available in Hall Effect and shunt variants.
-
Product
Quantum Sensors
-
Apogee offers two types of quantum sensors. The Full-spectrum Quantum Sensors feature an improved detector that provides accurate measurements under all light sources, including LEDs, right out of the box. The Original Quantum Sensor is less expensive and great for measuring all light sources except certain LED colors, where post-measurement correction factors need to be applied to achieve accurate readings.
