Solar Cell
Convert light to electricity.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Solar Power Meter
-
SOLAR POWER METER* 3 functions : Solar power, Power integration, Transmission* Select either W/m^2 or Btu / (ft^2xh) power units. Real time SD memory card Datalogger, it Built-in Clock and Calendar, real time data recorder.sampling time set from 1 second to 3600 seconds.Spectral 400 to 1100 nm2000 W/m^2, 634 Btu/( ft^2 x h )
-
Product
Battery Cell Surge Tester
Chroma 19311
-
Chroma Systems Solutions, Inc.
The 19311-10 has 10 channels, which can test up to 9 battery cells via scanning test, with a single unit. It can support up to 25 channels for testing up to 24 cells in a sequence by connecting with an external scanner (A190362). The test speed of the multicell scanning test by 19311-10 is extremely efficient, saving test time, and decreasing labor costs. It also increases the production capacity of the production line.
-
Product
Electrochemical Cell Accessories
-
Electrochemical cell accessories and components for laboratory and research applications, including electrode holders, sealing parts, and support systems. Designed for stable electrochemical setups and reliable experimental results.
-
Product
GTEM cells
-
Meets IEC/EN 61000-4-20, SAE J1752/3, IEC 62132-2 and IEC 61967-2. The GTEM cell is, in principle, a tapered coaxial line (offset septum plate), which is terminated by a hybrid combination of discrete resistors and RF absorbers to achieve a 50 Ohm broadband match. It is applied for Measuring of Emission, Radiated, radio frequency field-immunity test.
-
Product
PXI Mixed Configuration Relay Module - 13 Cells Populated
40-138-AA-BB-CC-DD (13 CELL)
Relay
The 40-138 2A Relay Module with 13 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Double-Layer Electrolytic Cell | Five-Neck Water-Jacket Design
DLF-1
-
DLF-1 double-layer electrolytic cell designed for temperature-controlled electrochemical experiments, electrocatalysis, and laboratory three-electrode systems. Available in single-layer and water-jacket configurations from 50ml to 500ml with five-neck structure and multiple PTFE sealing accessories.
-
Product
Solar
-
Chroma Systems Solutions, Inc.
This auto test system uses the unique test command optimization technology to prevent the repeating control commands from sending to the system hardware devices. This improves the system test speed dramatically and makes Chroma 8000, which uses open software architecture, highly efficient as a close or optimized auto test system.
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2
-
The TMO-2 Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The units provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Full scale output is specified at plus or minus 10 VDC. The TMO-2 provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability for applications such as weighing scales. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Solar Simulator (JIS AAA)
PEC-L12
-
A compact power supply box allows installation on a desktopThe irradiation direction can be freely rotated 360 degreesA 5cm square optical filter can be attachedQuiet shutter sound (equipped with a low-noise shutter)
-
Product
PXI Mixed Configuration Relay Module - 2 Cells Populated
40-138-AA-BB-CC-DD (2 CELL)
Relay
The 40-138 2A Relay Module with 2 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Scienlab Battery Test System — Cell Level
SL1002A
Test System
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Load Cell Tester
-
Xiamen Elane Electronics Company, Ltd
Large six-digit LED display < Easy to use and small in size < Accuracy of 0.005%FS/10ppm < 2 channels CH0 : -12mV/V~+12mV/V, with resolution 0.1uV/V CH1 : -1.6mV/V~+4.8mV/V, with resolution 0.01uV/V < Four user selectable output units (N, kgf, lbf and mv/V) < Peak Hold function to capture and holding the peak value for the immediate or later reference < Clear key to clear the peak value < Presence of tare key and foot switch to zero the display (tare function) < Great for monitoring and testing load cell characteristics (repeatability, linearity, creeping, temperature drift, etc
-
Product
PXI Mixed Configuration Relay Module - 5 Cells Populated
40-138-AA-BB-CC-DD (5 CELL)
Relay
The 40-138 2A Relay Module with 5 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Class AAA Steady State Solar Simulator
-
King Design Industrial Co., Ltd.
*Lamp average life 25,000 hours (We offer 1 year warranty including lamps)!*Spectrum Mis-match Class A, without filter! *Irradiance almost no decay within 10,000 hours!*Spectrum maintains stable during power adjustment!
-
Product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
-
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
Product
Heavy Duty Shear Beam Load Cells
SBL SERIES
-
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
Product
Large Volume Sealed Electrochemical Cell
LVS-1
-
Potentiolab Large-Volume Sealed Electrochemical Cell – High-capacity (1–3 L) borosilicate glass reactor with PTFE/Nylon multi-port lid, designed for sealed electrolysis, corrosion studies, battery research, electrosynthesis, and stable multi-electrode operation in demanding laboratory or industrial applications.
-
Product
Water Filler for Nickel-Cadmium Cells
MasterFiller
-
The MasterFiller is an instrument designed to deliver measured quantities of distilled water as required in the service of Aircraft Nickel-Cadmium batteries.· The MasterFiller consists of a microprocessor controlled pump with a level sensing probe, a keypad and display and an external 12VDC power supply (or optional battery).· The MasterFiller is part of a system comprising Intelligent Charger-Analyzers and Software for Battery Data Acquisition and Analysis, designed to improve the accuracy and efficiency of the process of testing batteries for airworthiness certification.
-
Product
Dry Heat Diffusion Cells
Phoenix Series
-
The Phoenix™ Diffusion Cell provides improved ease of use, high durability, and greater versatility as compared to conventional hand-blown vertical diffusion cells. Phoenix cells operate on dry heat; no water-jacketing is required, allowing construction from heavy-duty borosilicate glass held to very tight dimensional tolerances. The extract-and-replace sampling through the large diameter opening in the sampling arm accommodates standard pipette tips (~300 μL), simplifying the sampling process while reducing training and operating costs.
-
Product
Monitoring Solar Panel Strings, DC 30A, Φ10mm
CTF-30-10DC
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Compact, Space-saving, Low Cost DC Current Sensors.・Split-core type, easy to apply to existing circuit.・Easy to use by unipolar +5V power supply.・High speed responsibility – less than 10μsec. 0 rated primary current.・Suitable for monitoring solar panel strings.
-
Product
H-Type Optical Electrochemical Cell
HTO-1
-
HTO-1 H-Type Optical Electrochemical Cell is an electrochemical cell for laboratory research, designed for three-electrode testing, sealed or unsealed experiments, photocatalysis, corrosion studies, optical observation, or customized electrochemical workflows depending on the selected model.
-
Product
Robotic Cell for Testing Car Multimedia System
-
It is necessary to develop an automated system for testing a multimedia device. The system should perform functional testing: testing of physical buttons, touch screen and logic of operation.
